After the toilet flush is full, it is still trickling water and fine inlet water, and it takes a lon

Your water level is set too high, and the water will flow out of the toilet if it goes through the overflow hole next to the drain valve. Rotate the screw of the inlet valve counterclockwise to lower the water level, and the water will not pass through the overflow hole after the water is loaded, and it will be fine.

After the toilet flush is full, if the water still enters the west of the trickle, then the valve in this one is broken, and you can recheck it.

Hello, 1. Check whether the inlet angle valve is blocked 2. If there is no filter device on the toilet bowl, after a long time, the hose and both ends from passing through the angle valve to entering the toilet tank will also cause blockage. 3. It may be blocked by scale, or it may be caused by aging. Buy a brand new ** directly at 100-200, and there are dozens of cheap water pieces.

Specifically, you may have to ask a professional master to take a look at it, and then solve it according to the situation, so don't try it yourself for the sake of safety.

Generally, the float valve is broken, and there are several possibilities: the valve stem is broken, the water inside the float is ingress, and the rubber gasket of the valve is damaged. As soon as you open the lid, it will be clear at a glance.

Can't be continuously watered:

1. Whether the water inlet angle valve is blocked.

2. If there is no filter device for the water on the toilet, it will also cause blockage from the hose and the two ends from the angle valve to the toilet tank after a long time.

3. The water part on the left side of the figure is damaged. It may be a clogging of limescale, or it may be caused by aging. Buy a brand new ** directly at 100-200, and there are dozens of cheap water pieces.

In addition, I saw a mineral water bottle in **. It is estimated that the landlord wants to save water, and the idea is good, but this method does not work well. First of all, the water bottle can only reduce the total amount of water in the tank, and it is not effective in reducing the amount of water per flush.

This is because it is the amount of water that is set to determine the amount of flushing water.

Water-saving toilets are first of all pipe treatment, followed by water treatment, and many other reasons, water-saving is a series of transformation processes, adding water bottles has a general effect, and some toilets are easy to cause waste of water.

The toilet does not flush down, and the water is full when you press it.

Generally, the float valve is broken, and there are several possibilities: the valve stem is broken, the water inside the float is ingress, and the rubber gasket of the valve is damaged. As soon as you open the lid, it will be clear at a glance.

Can not be continuously watered: 1. Whether the inlet angle valve is blocked 2. If there is no filter device on the toilet bowl, after a long time, it will cause blockage from the hose and both ends from passing through the angle valve to entering the toilet tank. 3. The water part on the left side of the figure is damaged.

It may be a clogging of limescale, or it may be caused by aging. Buy a brand new ** directly at 100-200, and there are dozens of cheap water pieces. In addition, I saw a mineral water bottle in **.

It is estimated that the landlord wants to save water, and the idea is good, but this method does not work well. First of all, the water bottle can only reduce the total amount of water in the tank, and it is not effective in reducing the amount of water per flush. This is because it is the amount of water that is set to determine the amount of flushing water.

Water-saving toilets are first of all pipe treatment, followed by water treatment, and many other reasons, water-saving is a series of transformation processes, adding water bottles has a general effect, and some toilets are easy to cause waste of water.

Okay, I've also used hot water, and it doesn't work to sell dredging devices.

The toilet does not flush down, and the water is full when you press it.

Hello, I am happy to serve you and give you the following answers: it may be that the water tank inside the toilet is not drained, resulting in the water in the water tank and the hall not being discharged, and the water in the shed is full. The workaround is:

1. Check whether the drainage pipe in the water tank is blocked, if it is blocked, it can be cleaned with pipe cleaning agent; 2. Check whether the drain valve in the water tank is out of order, if it fails, you can replace the drain valve with a new one; 3. Check whether the water level control valve in the water tank is out of order, and if it fails, you can replace the water level control valve with a new one.

The toilet bowl will remain after flushing because the toilet flush valve is not closed tightly, and it can be repaired by the following methods.

Materials required: slotted taper, rubber sheet, double-sided tape.

1. Remove the drainage components first, and then you can remove them by turning them.

2. Pull up the top part of the water inlet assembly, there is a red clip on the pole, reach in and touch it up and down, and the blue part at the top can be rotated and dialed up.

3. The buckle on the blue lid should be pried open first, and the upper one can be pulled out.

4. There is a special sealing ring in the middle of the bottom of the float, which can inject water inside and bulge up, and finally close the water inlet valve.

5. Remove the rubber gasket at the bottom of the float, paste the rubber sheet to the bottom of the gasket with double-sided tape, trim it and then install it back, so that there will be no water leakage.

Open the water storage cover, and the position of the water outlet valve link, generally with a rope link, with a hand to pull the rope, will flush the part, this should be the cause of the problem, due to improper operation caused by the rope is too tight, press the tight rope to adjust to the appropriate position can be recovered.

The reason why the toilet does not stop flowing after use is that the plastic gasket on the outlet hole of the pumping system is aging and elastic enough to be sealed.

The solution is to open the toilet tank cover, find the water outlet hole, remove the rubber gasket, replace it with a new gasket, and then install and restore, and it's good to go. If you can't buy gasket accessories, you have to replace the entire flushing equipment. **Not expensive, generally around 50 yuan.

Gaskets are generally available in wholesale markets for household appliances in the city.

The whole set of flushing equipment is generally sold in hardware stores and plumbing equipment stores.

The replacement is simple, and it can generally be replaced by yourself. Some merchants can replace it on their behalf.

The plug in your toilet tank is aging! I suggest you go and change the water plug!

The quality of the water parts is not good for a period of time, and it will be like this for a while, and replacing a good water part is the bottom of the kettle.