Can sand plaster walls be painted directly? How to tile the sand plaster wall?

The sand gray wall cannot be directly painted, and the wall surface of the base layer must be treated first; Before placing the tiles on the wall, they should be soaked in water for two hours, so that they can be better fitted to the wall, and after soaking, they can be pasted directly on the wall.

No, you must shovel the wall skin first, soak the tiles in advance when pasting the tiles, and then you can choose the tile adhesive to paste.

In the process of home decoration, the sand-lime wall can not be directly painted, and the wall should be leveled with a layer of lime before it can be painted or tiled.

Gray sand walls can be painted directly with latex paint.

If the old wall is brushed with the original wall latex paint, the basic situation is better, there is no damage, the wall hair can be directly applied to the latex paint, but be careful not to destroy the integrity of the original wall paint film, and do not use latex paint The adhesion is much better than the original wall, otherwise it is easy to fall off; If the original wall at home is not good, it is recommended to redo the wall and then scrape putty on the latex paint.

And after grinding. It is not recommended to save the cost of wall decoration, otherwise various problems will easily occur in the later stage.

<> the wall base of the old house is not very good when the wall is refreshed, do not paint directly, the steps should be correct, and the old wall should be removed from the floating ash first, and the sand skin should be removed first.

After the wall is cleaned, the surface of the wall is cleaned, and then the interface agent is applied.

It can enhance the cohesion of the grassroots.

To evenly paint the wall, then blow putty, preferably twice, and then sand with finer sandpaper, after the sanding is completed, be sure to clean the wall thoroughly so as not to have too much dust and affect the adhesion of the paint.

The unevenness does not exceed 3 mm, and the primer and topcoat are applied at the end. Anyway, whether the old wall can be painted directly can not be distinguished, each household is different, the scheme of the wall is also different, combined with their own situation to judge the wall is best to directly polish the paint, paint or the whole refresh, at the same time, it is important to note that the old wall painted latex paint is a new one, need to deal with cracks and warping, for fine cracks, you can use elastic products to directly cover fine cracks.

For larger cracks, it is advisable to use primer mixed powder filling, evenly wiped and polished after low topcoat application. Please do not shovel the wall latex paint directly brush, if it is a house more than ten years ago, it is bigger, you need to shovel off the wall is to brush the paint, because the old house is used to refresh the putty, the quality of the paint is generally not very good, and the paint process also has certain shortcomings, the brush is relatively thick, and now the wall decoration is brushed with latex paint, because in the process of painting and paint water absorption, the putty of the old wall is easy to fall off, so the wall skin must have the ability to brush latex paint, Otherwise, do not apply latex paint directly, it may cause the wall paint to fall off.

It cannot be said directly, it must be brushed after the powder of the gray wall is removed, so that it can be stable, if it is brushed directly, it may not be durable enough.

No, you must first deal with the base layer, and then avoid the wall falling off and shovel off the original wall skin. After that, it is necessary to plaster and hang the net, and finally it is possible to apply latex paint.

Under normal circumstances, this is not done, because of the fear of cracking, the wall needs to be treated, and the lime sand wall needs to be removed.

There are two methods of paving: thin with tile adhesive and wet with cement mortar.

First, tile adhesive thin pasting method:

1. First of all, check whether the lime mortar wall surface is hollow and layered, and whether the lime mortar layer is firm and smooth.

2. When the above problems exist in the lime mortar layer wall, they should be eliminated and rectified in time.

3. Brush the interface agent on the base layer.

4. Paste the tiles with tile adhesive.

Second, cement mortar wet paving method:

1. Remove the lime mortar layer on the surface.

2. The uneven surface is plastered with cement mortar, and the wall is haired after drying.

3. After the chiseled wool layer is dried and fixed, sprinkle water on the chisel wool layer to moisten, and then paste it with cement mortar.

The first step is to remove the original wall skin, and the second step is to chisel the wall into a hemp surface. After cleaning, it is best to roll over the building, water the building, and then apply the tiles.

1. The wall is evenly dotted; 2. The last interface agent is then tiled.

It needs to be shoveled, cleaned, and then tiled.

There are two types of paving methods: tile adhesive thin pasting method and cement mortar wet paving method.

Tile adhesive thin lamination method:

1. First check whether the lime mortar wall of the wall is hollow and delaminated, and the firmness and flatness of the lime mortar layer;

2. If there are the above problems on the wall of the lime mortar layer, the problematic places need to be removed for rectification;

3. Brush the interface agent on the base layer;

4. Use tile adhesive for tile pasting.

Cement mortar wet paving method:

1. Remove the lime mortar layer on the surface;

2. The uneven surface is treated with cement mortar, and the wall is brushed after it is dried; (Note: Before doing cement mortar brushing treatment, the dry cement mortar plastering wall needs to be sprinkled with water to moisten it, and the purpose of sprinkling water is to prevent the dry wall from absorbing the moisture in the brushed mortar too quickly);

3. After the brushing layer is dry, sprinkle water on the brushing layer for moistening, and then use cement mortar to paste the tiles.

Remarks: The cement of the tile is ordinary Portland cement with a strength of megapascals, and the sand is medium river sand, and its ratio is proportioned according to the volume ratio, generally speaking, the ratio of cement sand paved with full ceramic tiles is about 1:2, and the volume ratio of cement sand paved with ceramic bricks is 1:3.

Steps for lime mortar wall tiling:

The first step is to remove the original wall skin, and the second step is to chisel the wall into a hemp surface.

Step 3: After cleaning, it is best to roll over the building, water the building, and then apply the tiles.

The sand-gray wall can not be directly painted, and the sand-gray wall base wall can be treated before tiling.

The mortar wall cannot be directly brushed, and the base surface must be treated first. Because sand-lime walls are more afraid of moisture than concrete walls. It should be noted that if the original sand and ash layer is loose, it must be completely eradicated.

Plastering and hanging nets on the wall again can increase the firmness of the wall, and can also avoid bulging, cracking, falling off and other phenomena when painting in the later stage. Soak the tiles in water for about 2 hours before placing them. The purpose is to allow the tile to absorb water in advance, so as to avoid the moisture in the binder after laying to affect the strength of the joint, or to make the binder shrink excessively, resulting in hollow drum transfer.

After submerging in water, remember to clean the surface with a cotton cloth and dry it before applying.

It is recommended to soak in water for two hours before tiling. It not only prevents cracking, but also allows the tiles to fit better against the wall. When pasting tiles, if you encounter the supporting parts of pipes and bathroom equipment, you must use the whole brick sleeve to cut and match, and you must not use non-whole bricks to patchwork and paste.

When buying ceramic tiles, it is recommended to buy more ceramic tiles, and there will generally be a loss of 8 to 10%. The principle of an expansion screw is that the screw expands inside the wall, creating a grip that makes the screw firm. The lime sand wall is soft, and it cannot make the screws form a grip in the wall, and it cannot play the role of expanding screws.

If the wall is uneven, then you must remember to polish it before decorating. During the polishing process, a large amount of dust is definitely generated. Therefore, construction personnel should remember to take protective measures to prevent dust from entering their respiratory tract, otherwise it will cause great harm to the body.

If you don't have any experience, it is not recommended to do it yourself. You can go to a professional for help, you can save a lot of trouble, and the effect is good. The wall decoration is relatively simple, but the details must be taken care of.

The walls of the bathroom and kitchen should be treated with moisture to avoid mold on the wall for a long time. After all, these two places use a lot of water, so they are humid all year round, and you can directly brush two layers of waterproof paint on the wall. The above is the answer to the question of whether the sand gray wall can be painted directly and how to apply tiles to the sand gray wall.

I don't think you can paint it directly, you have to brush it with a layer to cure, and then apply the tiles.

In the process of decoration, try not to apply paint directly, or should scrape putty first, so as to smooth the wall and improve the waterproof performance of the wall.

I think it can be painted directly, this kind of wall should be sanded first, and then brushed with 2 or 3 layers of curing agent, and then you can plaster cement tiles.

Check the condition of the wall. See if there are cracks or hollowing in the wall. If there is, you need to treat the wall first.

Check the waterproofing and brushing of the walls. If there is no problem, move on to the next step, if there is a problem, do it first, and it is very important to waterproof the wall. Brushing can increase the contact area between the tile and the wall.

The tiles need to be soaked in advance before pasting, and the bricks are not bubbling. Soak for at least two hours or more. If you mix it with mud and sand, be sure to pay attention to the proportions, and you don't need to soak the tiles when using them.

Sand gray wall is a common wall decoration material, which has the characteristics of good texture, durability and easy cleaning, so it has been widely used in home decoration. For the decoration of sand-plaster walls, you can choose to hang putty directly, but you need to pay attention to some details.

If you are not sure about the decoration materials on the market, you can find me to receive the local decoration cost reference standard, enter the area + city, accurately calculate each decoration cost, and also list, all kinds of main materials and auxiliary materials, the market price of construction costs and material schedules, and the owners can compare them one by one with the schedule! [Click here to get the most complete decoration schedule for 23 years (102 items attached), including main materials, auxiliary materials, construction costs, etc.**].

First of all, the sand-plaster wall can be hung directly with putty, but it is necessary to ensure that the wall surface is flat, dry, and free of oil stains. If there are obvious unevenness or cracks in the wall, it needs to be repaired before the putty is applied. After the putty construction is completed, it can be sanded to make the wall smoother.

Secondly, the decoration cost of the sand-lime wall varies from region to region, generally speaking, the decoration cost of the sand-lime wall is between 100-200 yuan per square meter. The exact cost is also affected by the following factors:

1.Wall condition: If there are many unevenness or cracks in the wall, it needs to be repaired, which will increase the cost of construction technology and materials.

2.Putty material selection: There are many different brands and qualities of putty materials available on the market, and there are also differences. Generally speaking, the better quality putty material** will be slightly higher.

3.Construction process: Different construction processes will have an impact on the cost. For example, if multiple putty applications and sanding are required, the cost will increase accordingly.

4.Construction team: Different construction teams may charge different fees, and generally speaking, experienced construction teams will charge a higher fee.

It should be noted that the above costs are for reference only, and the specific decoration costs need to be assessed according to the actual situation. When choosing a decoration company or construction team, you can make more comparisons, understand the ** and service content of different companies, and choose a cost-effective decoration plan.

Tuba Rabbit is one of the largest decoration platforms in China, with a total of more than 41 million owners, 110,000 decoration companies, covering more than 300 cities across the country, which can not only meet your decoration needs, but also provide specific decoration and decoration insurance services according to your budget (first decoration and last payment, safer funds, more bottom decoration. [If you don't want to be cheated, click here, and choose a decoration company that can be decorated first and paid later].

Kunming - [Kunming Decoration Strategy Guide].

Suzhou - [Suzhou Decoration Strategy Guide].

Hefei - [Hefei Decoration Strategy Guide].

Fuzhou - [Fuzhou Decoration Strategy Guide].

Beijing - [Beijing Decoration Strategy Guide].

Dalian - [Dalian Decoration Strategy Book].

Hangzhou - [Hangzhou Decoration Strategy Guide].

Shanghai - [Shanghai Decoration Strategy Guide].

Tianjin——[Tianjin Decoration Strategy Guide].

No, the steps of sand-gray wall decoration: 1. Clean the wall, wash the wall with water, and wait for the wall to dry before starting; 2. Prepare the materials, modulate the slurry, and mix it according to the correct proportion during debugging; 3. Formal construction, painting paste on the wall, it needs to be evenly covered, so that it can penetrate into the wall; Fourth, the slurry needs to be brushed for about half an hour, and there can be no accumulation; 5. Continue to apply the slurry, almost three times.

1. The sand-gray wall cannot be scraped directly with putty, and no matter what type of wall it is, it needs to be polished before scraping putty, otherwise it is likely to affect the effect of scraping putty. 2. After polishing the wall, the wall can look smoother and smoother, and the dust on it should be cleaned up, so that the putty effect will be better, and it can also be conducive to the later wall decoration.

Applying putty ash to a polished wall is relatively simple. It is to mix glue, talcum powder and cellulose thoroughly, scrape the wall evenly with a scraper, and wrap the sandpaper on a flat small wooden board after drying. Carefully sand the walls.

Sand and gray walls can not be scraped directly with putty, no matter what type of wall, you need to polish first and then scrape putty, otherwise it is likely to affect the effect of scraping putty.