Is it necessary to paint the wall solid? What is the function of wall reinforcement?

It is necessary to brush the wall solid, and the role of the wall solid: seal the wall dust. As long as it is removed, it is difficult to avoid causing a lot of dust, if this dust is mixed in each step of the wall solution, it will immediately cause the plastering layer behind to be unable to be firmly pasted with the original wall, resulting in the wall powder, and even cracking, so there must be a strong permeability like the interface agent and the wall solid, and the dust curse is tightly printed on the surface of the wall.

In addition to the unsealing solid dust, because the interface agent has the composition of glue, it can also improve the adhesion of the gypsum screed, which can make all wall projects stronger. Therefore, it is indispensable to brush the wall with an interface agent. The wall solid has excellent water permeability, which can very well infiltrate the surface of the wall base layer, make the base layer close through gluing, improve the adhesion of the page, improve the adhesion of mortar or putty powder and the wall surface, and prevent the wall from hollowing.

In fact, wall solidification is a kind of interface agent, which is mainly used to connect the previous and the next, tamping the substrate and allowing the covering of other components. If there is some dust on the page, it is okay to use it on the title page. However, if the ratio of cement mortar on the wall of the owner's home is moderate, or the quality of the plaster leveled on the ground is qualified, each process is in accordance with the construction standard, and the wall can actually be fixed.

Nowadays, more and more people apply colored wall solids, there may be some people who think that it will harm the adhesion, in fact, this is not the case, often the application of colored wall solids, mainly has the effect of facilitating management, for example: the interface agent is light yellow, so that it can detect putty powder, wall paint is not qualified.

If the quality of the wall is unqualified, the page is too smooth or the base layer is not clean, etc., it will continue to lead to the situation of wall hierarchy. Therefore, everyone should leave more quality of wall solidification, whether it is cleared. To put it bluntly, the wall is dry and solid, a kind of interface agent, which has excellent water permeability, can fully infiltrate the surface of the raw materials of the wall base layer, make the base layer compact, improve the adhesion of the page, the bonding strength of mortar or putty powder and the wall, and avoid the hollowing of the wall.

Applicable brick-concrete structure wall batch putty, the density of the base layer before the batch of putty is solved, and the adhesion of the smooth base can also be improved, that is, the bonding of the wall cloth and wallpaper is more flat, and it is not easy to cause wrapping and dead folds. Generally speaking, the wall is a contracting effect, which solidifies the industrial base and makes it easier to solve the wall behind it. In addition, wall painting can reduce the probability of wall cracking.

It is necessary to brush the wall solid; The wall solid is mainly to stabilize the base, so that there will be no hollowing or blistering, which can increase the permeability of the wall, and the wall solid is also a green and environmentally friendly product, and the overall practicability is particularly strong.

It is necessary to brush the solid wall; The function of the wall protection is to effectively enhance the adhesion, but also to make the wall more firm, so as to effectively prevent cracking, but also effectively prevent moisture, but also prevent mold.

It is necessary. wall solid.

It is a green and environmentally friendly material for wall curing, which can achieve the curing of the wall, enhance the adhesion of the foundation, and inhibit the anti-alkali of the wall.

1. Wall solidification is a wall curing adhesive, which is a substitute for 108 glue and interface agent, and is a green environmental protection and high-performance interface treatment material. It has excellent permeability, can fully infiltrate the surface of the wall base material, make the base layer dense through gluing, improve the interface adhesion, improve the bonding strength of the mortar or putty and the wall surface, and prevent hollowing. It is suitable for the dense treatment of the base layer before plastering and scraping putty on brick-concrete walls.

Wall solidification can improve the adhesion of smooth base layers, and is an alternative product of traditional building interface agents. It is also suitable for the bonding of wallcovering and wallpaper. Due to the easy coating, thin adhesive film and suitable initial tack, it is especially suitable for the smooth bonding of wallcloth and wallpaper, and it is not easy to produce dead folds and bulges.

It can also be used on substrates"Hairmaking"。

2. The wall solid has excellent permeability, which can fully infiltrate the surface of the substrate, make the base layer dense, and improve the adhesion of the smooth interface. The wall solid is non-toxic, tasteless, and is a green and environmentally friendly product. The surface of the base layer should be solid and free of floating ash and oil stains.

Substrate interface treatment: dilute the wall solid with 50-60% water, apply it to the substrate with a roller brush, and apply it 1 to 2 times. Hairmaking

Mix cement and wall solids into a paste, and apply it to the base layer with a tool.

Because the floor and wall of most of the new houses are not in place during the painting construction, not to mention the hollowing, cracking, and sanding in the future. After the owner takes over the house, he generally rarely removes the screed layer and stucco layer of the ground and wall (the cost is very high and the construction period is extended), but it is necessary to repair the original ground and wall. This is also the only way to solve the problem of the embryonic room that can be found at present, and the causes of this kind of problem are mainly in three aspects:

First, the cement in the mortar is not marked enough and the structural force is insufficient;

second, the proportion of cement in the mortar is insufficient;

Third, the soil content of the mortar used is too high, which affects the structural force of the stucco layer;

Wall solidification - that is, cement wall and ground curing agent, suitable for the curing treatment of cement wall and ground in the early stage of home decoration or engineering decoration, which is convenient for ground cleaning. Generally speaking, the cement floor of home improvement or tooling is not solid, and there is a phenomenon of running sand.

Causes of sand running:

1. The cement label used in the mortar is insufficient.

2. The proportion of cement in the mortar is low.

3. The soil content in the mortar is too high.

If there is a phenomenon of running sand, the cement floor is loose and difficult to clean, and a large amount of floating dust will appear every time it is cleaned. This not only causes pollution to the environment, but also adheres to the dust particles of the cement floor on the working surface during the subsequent construction process, thereby reducing the quality of batch scraping putty and latex paint.

The appearance of wall solidification can avoid the above problems, wall solid.

The imported polymer is compounded through multiple processes, and the polymer can penetrate the cement floor, firmly block the loose particles of the cement floor, so that the ground forms a close integration, which is convenient for the close combination of decorative materials and the ground, and effectively prevents the hollowing of the floor tiles.

The wall is resistant to water and moisture, which can avoid the deformation of the wooden floor due to moisture erosion, and at the same time avoid "dusting" from the cracks of the floor in the future.

Wall solid products do not contain formaldehyde and other harmful substances, are green and environmentally friendly products, and are harmless to the human body.

How to tell if the wall is good or bad?

1. First of all, open the barrel to observe whether the wall is uniform, there should be no delamination, agglomeration, and pungent odor.

2. During the construction process, the wall should not produce a large number of pungent odors, and the smell should not remain for a long time after the construction is completed.

3. Wall solid is a kind of permeable curing agent, the firmness of the wall should be significantly improved after the construction is completed, and the wall solid penetrates the base but there should be no obvious film formation on the surface.

4. The wall should have water resistance, and the water will not fall off or fade after the construction is completed. If the glue type wall is thick and thick, there will be obvious film formation, and the coating film is not water-resistant, and there is a great risk of bleeding and peeling of the late tiling or batch scraping putty powder.

5. In addition to the above performance, it should also have bright colors. As for adding powder to the wall solids for better coverage, this product will significantly sacrifice the curing ability of the wall solids to the base layer.

The function of wall brushing: improve the adhesion, avoid hollowing and cracking, and inhibit the anti-alkali of the wall. Round beams

1. Improve adhesion: wall solidification can improve the adhesion of the wall and help the subsequent construction. Its function is equivalent to adding an extra layer of glue between the wall base treatment and the next process to improve the adhesion, but it does not have the effect of waterproof and moisture-proof.

2. Avoid hollowing and cracking the phenomenon: before brushing putty and latex paint, the wall should be treated locally, and the use of wall solidification can reduce the probability of sand particles or unevenness when scraping putty in the future, and can also reduce the hollowing and cracking of the wall after painting latex paint, so that the wall base is more firm.

3. It has an inhibitory effect on the anti-alkali of the wall: the wall solid can also play a corresponding inhibitory role in the alkali return of the cement wall.

How to use wall fixing

1. Scrape putty: Before scraping putty, you can use gypsum to level the wall, and then scrape putty on the wall, you can choose a delicate putty material, and the putty material should be evenly smeared on the wall, so as to form a better decorative effect.

3. Brush latex paint: After the putty is scraped, you can brush the wall with latex paint, generally brush the latex paint twice, and when brushing the latex paint, it should be in accordance with the order and evenly smeared, so that the wall is more flat and smooth.

4. Cleaning and inspection: After the latex paint is brushed, you can check the wall to see whether the color of the wall is consistent, whether there is powder, blistering, etc., if these situations occur, they should be dealt with in time.

1. Prevent hollowing.

The wall solid has good permeability, can well infiltrate the surface of the wall base layer, and makes the base layer tight through gluing, improves the interface adhesion, improves the adhesion between the mortar or putty and the wall surface, and avoids hollowing. In fact, wall solidification is a kind of interface agent, which is mainly used to connect the previous and the next, consolidate the substrate and allow the coverage of other substances. If there is some powder on the interface, it is also possible to use it for the back cover.

However, if the ratio of cement mortar on the wall of the owner's home is appropriate, or the quality of the leveled gypsum is qualified, each step is in accordance with the construction standard, in fact, the wall can not be solidified.

2. Inspect the wall treatment process.

Nowadays, more and more people use colored wall solids, and some people may feel that they will affect adhesion, but this is not the case, and the reason why colored wall solids are used is mainly to facilitate management. For example, the interface agent is yellow, which can detect whether the putty and wall paint are up to standard.

However, it should also be noted that if the quality of the wall is not up to standard, the interface is too smooth or the base layer is not clean, etc., it will also cause the phenomenon of wall delamination. Therefore, we should leave more to see if the quality of the wall is passed.

Different uses, the use of wall solids is different. For example, if the wall is brushed, the wall can be fixed and the water according to 1:

Avoid hollow drums. In fact, wall solidification is a kind of interface agent, which mainly plays the role of connecting the upper and lower levels, consolidating the substrate and allowing the coverage of other substances. If there is some powder on the interface, it is also possible to use it for the back cover.

When we carry out interior decoration, we need to use a variety of decoration materials for the curved bridge, and in general, the owner does not know much about the decoration of building materials, and does not know that these materials are not necessarily used. For example, if the decoration company recommends the owner to buy wall solids, is it inherently necessary to paint the wall? Next, I will briefly introduce it to you.

1. Wall solidification refers to wall curing adhesive, which is an environmentally friendly and high-performance interface treatment material. Before plastering and scraping putty on the brick-concrete wall, people will first paint the wall with curing glue. Because the wall curing adhesive plays the role of connecting the upper and lower levels, it can improve the adhesion of the base layer, make the base solid, and prevent the wall from hollowing and cracking to a certain extent.

2. Whether you need to use wall fixing to paint the wall mainly depends on the wall situation of our interior. If the cement mortar of the wall and the plaster of leveling are appropriate, the quality is qualified, and each step of the construction is carried out in accordance with the standard, then there is no need to use the wall solid. If the walls in our interior are cement mortar walls, then it is better to use wall solids.

3. In the process of indoor construction, we can wait until the water and electricity renovation of the house is completed, and then brush the wall before leveling the buried imitation wall. The construction environment is dry and well-ventilated, and the temperature should not be lower than 5 degrees Celsius. After you clean the base layer, you can debug the product according to the instructions for use, and you can brush the wall once or twice.

We can mix the wall solid and cement in a certain proportion, and then apply it to the base layer.

When we carry out interior decoration, it is best to use wall reinforcement base, if the quality of the cement mortar layer is excellent, you can not use it. When using wall fixing, we need to pay attention to the fact that the thicker the wall reinforcement product, the better.

Ground solidification and walls are inherently not necessary to paint depending on the specific situation:

1. If the wall of the home meets the needs of subsequent decoration, such as the wall is hard, the feel is stable, there is no loose structure, no dust, you can do not need to brush the wall. However, if the cement splash layer is loose, the silt is severe, or the wall of the old house is renovated, it is better to brush the wall.

2. If there is no sand on the ground at home, the ground leveling has been done, in fact, it can be fixed without brushing. However, if the ground sand is serious and the ground leveling is not done, it is best to brush the ground.

1. Wall solid contains some harmful substances, especially formaldehyde. Formaldehyde is more harmful to the human body. Long-term exposure may cause ** problems, and in severe cases, it may also cause cancer, which may induce leukemia.

2. There are still many manufacturers who produce wall solids, and if you choose products produced by small manufacturers, there are still many hazards. First of all, the toxicity is still very large, if it is absorbed by the human body, it will have an impact, and more importantly, small manufacturers will definitely cut corners in the production process, so the quality of this product is not particularly good, and it does not meet the requirements of waterproofing.

3. In fact, the material of the wall hanging is actually very good, and the waterproof penetration function is also good, and the performance itself is also very good, mainly because everyone must be clear about the brand when buying, and it is best to buy a regular wall solid brand, so the impact will be slightly smaller.

With the use of wall solid, there is no need to hang the net anymore. After the wall is painted with wall solid, an interface layer will be formed, so that some loose places on the wall will be connected, so that it will become more firm, so that there is no need to worry about cracking when scraping putty or leveling in the later stage, and the construction is more convenient.