How to wrap tennis hand glue, how to wrap tennis racket hand glue

Wrapping the handle sweatband is an important preparation for badminton, and it will fall apart after a while, which will affect the feeling and comfort of playing. The correct way is:

1. Peel off the protective film on the surface of the hand glue, this side of the hand glue is wrapped on the outside and is in contact with the palm, and the other side is wrapped inside and in contact with the handle.

2. Uncover the double-sided tape on the tip of the hand glue, which is the place where the hand glue begins, and stick it to the end of the handle to fix it.

3. Tighten the hand glue moderately to make the glue surface slightly deformed, which can make the glue surface more suitable for the handle and not easy to shift. At the same time, the thumb of the left hand presses the rubber surface to prevent rebound, and slowly wraps the hand glue on the handle.

4. Wrap the sealing strip, which is similar to the method of wrapping hand glue, press on one side, and start to pull on the other side. The finished rubber surface is very thin, and there is almost no unevenness when you touch it.

If you can ask the shopkeeper to help, you will help as soon as you do it. You can also start from the bottom of the handlebar, work your way up to the neck, and finally dip the tape of the handguard on.

Generally, it is wound from the bottom of the handle to the top (the direction of the head), and it seems to vary from person to person whether it starts from the big end or the small head of the hand glue.

Personally, I think it should be wrapped from the small head, and the bottom will look more even, but I am worried that the small piece of sticker will stain my cowhide handle, so I learned from our coach and teammates, wrap it from the big head, and then wrap it to the end and pat the throat with the small sticker, so that it will not stick to the inner stem.

It's comfortable to wrap yourself, it's okay to hold comfortably, you don't need to find any authoritative winding, everyone will care about how you wrap the ball, maybe you will learn how to wrap it, hehe.

1.Take out a roll of sweatbands or hand glue.

2.Tear off the outermost layer of white tape and leave it for later use.

3.Untie the glue and remove the inner core of the plastic tube in the middle.

4.Peel off the plastic protective film on the surface of the hand glue.

5.Find the end of the small head and tear off the double pin gel on the back of the small head.

6.Place the small head beveled.

Part of the shoot towards the end of the beat, and the double-sided tape is pasted on. Things are clear.

7.Double-sided tape is applied to the smaller one.

8.The right-hand gripper holds the racket with the left hand and wraps the glue with the right hand (the opposite is true for the left-handed gripper).

9.The end of the shoot is tightened, and the glue is wrapped along the edge at first, and then wrapped in a short section after overlapping, and then wraps downward, leaving no wrinkles. Except for the end part, the overlapping part of the other upper and lower layers of hand glue is about 2 3mm.

10.In the end, there will generally be an extra part, use scissors to cut the extra part out of an inclined plane, try to leave a little longer to avoid cutting short and not good winding.

11.Tear off the tape that was left at the beginning.

12.Glue the tape to the end of the glue, wrap it horizontally in the direction of the glue, and keep it neat.

13.Finally, put the rubber band (hand glue) for the end of the tennis racket and put it on the white tape, and it doesn't matter if you don't have this rubber band.

Basic knowledge: If you want to wrap the tennis racket hand glue, first figure out some basic knowledge about the net racket hand glue. Generally, the length of the outer stalk skin is relatively fixed, about 125 cm.

However, the handle of different beats is different. For example, the handle of the Verson "Weilun" is about 19 centimeters long, while the handle of Dunlop "Top" is about 19 centimeters long. Each racket has different thickness specifications for the handle, so the density of the outer handle should also be flexibly controlled.

Thin and short rackets with a thin handle should be slightly larger when crimping, about 2 mm.

Method steps: Start to practice the tennis racket hand glue wrapping method: the beginning part of the outer handle is narrow, and the wrapping should start from the bottom of the handle, first align the edge with the bottom of the handle, and slowly rotate the handle to make the handle around the handle.

Note: When winding, the force should be even, neither too loose nor too tight - too loose winding is not only unsightly, but also easy to loosen or wrinkle; If it is too tight, the shank will deform and the feel will be too hard. If you wrap it to the end, there are still some leftovers that can be trimmed with scissors.

2.The last and most crucial step in the tennis racket hand wrapping method: the finishing part.

Do you still remember the small Pei round strip with the logo printed on the handle that collapsed and was tied to the handle at the beginning? What, thrown?!Hurry up and pick it up!

That's the glue annihilation ribbon that plays a key fixed role, and whether it can be successfully closed depends on the little guy. Without it, all the work just done was in vain! It's like finally putting on your pants and suddenly realizing that you just threw the belt!

When tying the belt, you should pay attention to: don't be busy tearing off the adhesive paper, tear it with the sticking, and be careful not to let your fingers touch the rubber surface.

How to wrap the tennis racket hand glue is introduced as follows:

The first step of hand glue wrapping: There are two commonly used hand glues, one is adhesive hand glue with film, and the other is dry hand glue without film. If it is an adhesive hand glue, first remove the protective film on the surface of the hand glue, this side of the hand glue is wrapped on the outside and is in contact with the palm, and the other side is wrapped inside and is in contact with the handle.

The second step of the hand glue wrapping method: uncover the double-sided tape of the tip of the hand glue, this is the place where the hand glue begins, and attach it to the end of the handle to fix it.

The third step of the hand glue wrapping method: the right hand moderately tightens the hand glue, it is important to pay attention to this, so that the rubber surface is slightly deformed, which can make the rubber surface more suitable for the handle of the shoot is not easy to shift, and the right hand pulls at the same time, the left thumb presses the rubber surface to prevent rebound, and slowly wraps the hand glue on the handle. Note that it is slightly deformed, not too deformed.

The fourth step of the hand glue wrapping method: use scissors to cut the hand glue into a bevel to facilitate sealing.

The fifth step of the hand glue wrapping method: start sealing, but at this time there is still something missing, at this time another accessory of the hand glue begins to appear is the sealing strip, similar to insulating tape.

The sixth step of the hand glue wrapping method: the method of wrapping the sealing strip is similar to that of the hand glue, pressing on one side and starting to pull on the other side. The rubber surface after pulling off is very thin, and there is almost no unevenness when you touch it.

You can also choose to use strong sticky and thin insulating tape, because it is wider than the self-contained sealing glue, which is not easy to loosen, and it is very easy to use.

Generally, the length of the outer stalk skin is relatively fixed, about 125 cm. However, the handle of different beats is different. For example, the handle of the Verson "Weilun" is about 19 centimeters long, while the handle of Dunlop "Top" is about 19 centimeters long.

The handle of each racket also has different thickness specifications, and the racket with a thin and short handle should be slightly larger when crimping, about 2 mm.

The correct way to wrap the badminton hand glue is as follows:

Tools: badminton racket, keel hand glue.

1. Start winding from the bottom of the racket, tear off the double-sided tape at the end, and glue the punch stool at an angle parallel to the hypotenuse of the sweatband and the plane of the bottom bracket, and fix and compact.

2. After the end of the hypotenuse, it begins to wind upward, due to the different diameters of the bottom bracket and the wooden handle, it needs to be tightened in the first two circles, otherwise there will be folds as shown in the arrow, which will affect the appearance and feel.

3. After starting to wrap three times, enter the stage of wrapping the wooden handle, please keep a small force winding at this stage, because the elasticity of the EVA strip is limited, and pulling too tightly will reduce the expansion space of EVA and affect the shock absorption effect.

4. Similar to the second step, when winding to the front cover stage of the handle, the first large scattering force, otherwise the sweatband will also be wrinkled here because of the change in diameter.

5. For the end of the racket, we recommend wrapping it to the top of the handle before the game, and fold the last 2cm of the suction belt in half to achieve the best aesthetic effect.