What to do if the bottom of the faucet is loose? How to tighten the kitchen faucet when it is loose

The bottom of the faucet is likely to be loose because the faucet has been used for a long time, and the lower part of the gasket is aging or the connection thread is corroded, so the lower interface of the faucet should be replaced again or the new faucet should be replaced directly, and the specific disassembly and replacement steps are as follows:

1. First of all, close the hot and cold water valve under the wash basin for disassembly.

2. Use a movable wrench to remove the connecting screws between the hot and cold water pipes and the faucet.

3. Remove the two screws that fix the faucet.

4. Remove the rusted drain, and when buying the drain, ensure that the threads are consistent, otherwise the installation will not be possible.

5. Put the purchased nozzle at the installation position, and put a rubber pad on the two pipes respectively to make a waterproof seal.

6. Tighten the plastic screws under the faucet and connect the hot and cold water pipes.

7. Finally, the new installation is completed.

Reach in from under the basin and find the bottom of the faucet, there is a relatively large nut, and you can tighten it by hand.

Go to the hardware store to buy some raw material with a large valve unloader faucet (if you don't have a wrench, remember to ask the hardware store owner to borrow it), wrap the raw material belt on the thread of a circle (remember to dry it) and then turn it up and open the big valve again. . .

There is a hexagonal nut at the bottom of the faucet, you can take a relatively large activity wrench to tighten it directly, or you can change to a quick plastic holder to try, plumbing equipment stores are available, online shopping is also available!

1. If the handle of the faucet is loose, use a small driver to lift the small round cover on the handle, and tighten the fastening screws inside with a special Allen wrench.

2. If the faucet holder is loose, tighten the fixing screw from under the sink on the countertop.

3. If the faucet is loose, it may be a little slippery. It is recommended to use a very small rubber sheet or shaft gasket, cut into a small circle, dig a small hole in the middle, and then put it under the nut, and tighten it with a plate wrench, and you can tighten the loose faucet. When you use it in daily life, you also need to take good care of it.

1. The sealing gasket in the gland is worn: close the main water valve first, loosen the screws and remove the bolt head and gland, take out the sealing ring from the inside of the gland, replace it with a new sealing ring, and reinstall it.

2. Silk tooth fracture phenomenon: please ask a professional master to replace the regret.

3. Loose screws: The screws are relatively humid near the pool, the screws are easy to rust, and the daily switch causes the fixing screws to fall off is normal, and it can be fixed with a wrench after inspection.

4. Lack of raw material belt during installation: the old-fashioned faucet is reinforced with hemp rope and raw material belt, buy some raw material belt and wrap it around the interface of the sewer pipe and faucet, and try to wrap it tightly to ensure the stability of the interface. The handover between the faucet and the basin is best fixed with waterproof glass glue or double-tube resin glue.

Faucet Material:

1. Stainless steel faucet: Now the most used is the stainless steel faucet, this kind of material faucet does not contain lead, and acid and alkali resistance, no corrosion, will not pollute the tap water, will not release harmful substances, etc. Stainless steel faucets do not require plating, and can be polished to reveal their true color.

Rust, no oxidation, no wear and other advantages, the appearance is beautiful and generous, because the shell is also made of ceramic balance.

2. All copper faucet: The quality of the all-copper faucet mainly depends on its own copper content and its process level, if the faucet is made of all-copper refining, and the surface is also chrome-plated, then the gloss of the faucet will be very high, and its corrosion resistance and anti-wear performance are very good.

3. Plastic faucets: Compared with faucets made of other materials, the safety of the use of plastic faucets will be higher, because they are made of ABS plastic, and the faucets are more colorful, and consumers have more choices.

4. Alloy faucet: The alloy faucet will be much more affordable than the all-copper faucet, and it can also be mass-produced.

5. Ceramic faucet: The advantage of ceramic faucet is that it will not oxidize, rust, and not easy to wear, and the faucet made of ceramic has a beautiful appearance.

Faucets are an indispensable hardware product in our daily life, which brings us the convenience of water. However, due to frequent use, improper use can also cause the faucet to loosen. So what should I do if the faucet is loose and will sway from side to side?

What to do if the faucet is loose and will shake from side to side: First of all, the faucet shaking may be that the fixed screw is falling off or loose, and it is recommended to fix it with a wrench; Secondly, it may be caused by the wear and tear of the raw tape or the sealing ring of the faucet, so it is recommended to re-wrap the raw tape and replace the new sealing ring to ensure that the interface is stable; Finally, it may be that the silk teeth of the faucet are worn or broken, and it is recommended to find a professional master to replace them.

How to maintain the faucet daily:

1. When using the faucet daily, it is necessary to regularly wipe the surface of the faucet with a wrung out cotton cloth, if the water output of the faucet is found to be less for a period of time, it may be that the screen is blocked by less water, it is recommended to unscrew the screen cover to clear it to ensure the normal water output.

2. When using the faucet, whether it is open or closed, it should not be too forceful, just rotate it with the trend, otherwise it will damage the sealing valve of the faucet, resulting in the faucet not being closed tightly and leaking.

3. When the faucet in the bathroom is in use, the metal hose of the faucet should be kept in a natural and comfortable state, and the hose of the faucet should not be wound around the faucet, otherwise the hose will be broken or damaged.

4. Finally, when installing the faucet, it is best to ask experienced professionals to install, and when installing, do not contact the faucet with hard objects, cement, glue, etc., otherwise it will damage the gloss of the surface coating of the faucet. In addition, when installing faucets, be sure to remove the debris in the pipes before installing.

Summary: The above is the introduction of the faucet loose will shake left and right and how to maintain the faucet daily related content, I hope to help friends in need, if you need to know more about related knowledge in the later stage, welcome to pay attention to Qeeka Home.