How do you fix a toilet suck? How to fix a broken toilet drain

1.Lift the floating arm upwards. If the water stops flowing, the problem is that the float cannot be lifted high enough to press the valve plunger into the float valve. One of the reasons for this may be the friction between the float and the wall of the tank, and if this is the case, bend it slightly.

2.If the float is not touching the tank, hold on to the float arm and then turn the float counterclockwise to remove it from the end of the float.

3.If none of the above methods solve the problem, check the tank ball plug at the flush valve seat. Chemical residues in the water can cause ball plugs.

4.If there is still an excess of water flowing through the flush toilet, it may be that the steel rope of the ball plug of the lifting tank is not in the right position, which can lead to.

If the toilet is backfilled, it can be solved by installing a toilet overflow prevention device. This device is a flushing valve in the field of drainage.

The toilet anti-backfill device can be installed between the fecal pipe and the porcelain ring under the toilet, so that the sleeve mouth can be blocked to death, and there will be no backflow problem, the effect is remarkable, and it is very suitable for high-rise or multi-storey second and third-floor residents.

This e, this may be this, it may be that you are pretending to be pregnant, you may be pretending to be pregnant, you remove it, and then do it again.

If the toilet at home fails, you need to find a way to solve it. How do you fix a broken toilet flush? PChouse will take you to find out.

First of all, we need to determine whether the closing valve of the toilet is in a closed state, in some cases, the upper closing valve may be closed, at this time, how you open the toilet can not have water flow, or some parts of the closing valve are faulty, which will also cause the water to continue to flow out, there is a gasket inside, if there is damage, it needs to be replaced in time, and at the same time to ensure that the float valve of the toilet is sealed, or it must be completely replaced, so as to effectively solve the problem of toilet pumping.

If the toilet flush is damaged, it will not be able to flush properly. First of all, close the main valve of your house and drain all the water in the toilet. Then use a pipe wrench to loosen the nut of the union, and the valve can be removed directly.

Then the connection place of the water inlet pipe is wound through the raw meal belt to ensure that the water inlet is normal. Finally, the flush should be replaced, and after replacing it with a new one, it should be wrapped in a raw meal bag to ensure that it is tightly wound, so as to ensure normal flushing.

1.Start by turning off the water source: Find the water pipe at the bottom of the toilet bowl and turn it clockwise to close the valve to stop the water flow.

2.Empty the toilet: Drain the toilet with water using a suction or by pouring it into a bucket.

3.To remove the toilet seat: Remove the toilet seat and place it in a safe place.

4.Check the inside of the toilet: Check the inside of the toilet for blockages or breaks, and repair or replace them if necessary.

5.Replace the internal parts of the toilet: If there is a problem with the internal parts of the toilet, it needs to be replaced. For example, if there is a problem with the float inside the tank, a new float will need to be replaced.

6.Clean the toilet: Use detergent and brushes to clean the inside of the toilet bowl to ensure that the toilet bowl is clean and hygienic.

7.Installing the toilet seat: Install the toilet seat back in place. File blind accompaniment.

8.Turn on the water source: Turn the valve clockwise to turn on the water source and check if the toilet is working properly.

9.Test the toilet: Flush to test if the toilet is working properly, if there is a problem that needs to be re-inspected and repaired.

Summary. Dear, hello, 1. Check whether the toilet tank is clogged:

Open the toilet tank first, because the toilet tank is a part that many people will ignore, so after long-term use, there may be more impurities in the water tank, resulting in the water tank being blocked, so that the toilet tank does not water. In this case, it is necessary to clean the water tank with a partially used toothbrush or a partial cleaning tool, and attention should be paid to the regular cleaning of the water tank in daily life.

The toilet does not suck: how to repair the water when it goes out.

Hello dear! I'm Mr. Liang, and I'm glad to serve you. The cumulative consulting service has exceeded 1,000 people, let me destroy the fight to answer for you to change the socks is sorting out the answer, please be patient and wait for a nuclear aftermath to get under it! 

Dear, hello, 1, check whether the toilet tank is blocked: first open the toilet tank, because the toilet water fuel tank is a part that many people will ignore, so after long-term use, the impurities in the tank may accumulate more skin knowledge, resulting in the water tank blockage, so that the toilet tank is not water. In this case, the tank needs to be cleaned with a partially used toothbrush or a partial cleaning tool, and attention should be paid to regular cleaning of the tank in daily life.

Dig up the button of the toilet tank: When the skin is vertical, the toilet tank does not pump due to the failure of the button in the toilet tank. If the spring of the button inside is no longer elastic, then you only need to buy a button of the same size to replace it, so that the toilet tank can pump and use the liquid properly.

Than the heart] [than the heart].

What should I do if the dirty water in the toilet can't be sucked away?

You press it with the toilet seat, and the pressure will suck the sewage away, so try it.