Is it better to use red bricks or light bricks to build walls? Is it stronger to use red bricks?

If you look at the material of bricks, the density of red bricks is higher than that of light bricks.

Walls built with red brick will be stronger than walls made of light brick, but in high-rise buildings with large areas of red brick.

, the state prohibits its use because of the heavy weight. If every homeowner is free to use the house, who will be responsible in case something goes wrong? The walls we built had little bearing capacity, the floors were supported by concrete columns and beams, and the new walls were just fillers.

As far as the whole house is concerned, you are more or less fine.

<> again from the national standard, the building standard is higher than the home decoration standard, and the house is built with lightweight bricks, so why can't we decorate? The place where the decorative red brick is used at home is the bagged pipe and the bottom beam, the toilet wall is considered to be used, and the use of lightweight bricks elsewhere is sufficient. It is not known who invented the practice of building a layer of light bricks in two rows of red bricks in turn.

No one has tested whether this wall is stronger than a wall made of lightweight bricks. Why do people say it's a better way to build a wall?

Now a lot of homeowners are scared away by these ** on the internet. If you want to see a wall, you can find many ways on the internet. This is to attract attention, to take out the effort to scrub the phone, to open the national standards, these standards are the conclusions of experts through data, these standards are credible, and there will be no problem in building according to these standards.

Red bricks are also known as solid clay bricks (referred to as red bricks). Red bricks are made of clay, shale and gangue.

It is the main material, which is crushed, stirred and kneaded, and pressed manually or mechanically at an oxidizing flame temperature of about 900 degrees.

Below, it is made of sintered building bricks. The production process of red bricks is relatively simple, can be manufactured by machinery, has high production efficiency and is widely used, because of the use of solid brick production, red bricks have the characteristics of waterproof, not afraid of moisture, and good thermal insulation performance. Many of the early buildings were brick and concrete structures.

So they are always built with red bricks, but modern high-rise frame structures.

Houses also have a number of drawbacks.

It is better to use red bricks, red bricks are not easy to crack, the waterproof effect is particularly good, the load-bearing properties of red bricks are particularly good, very stable, it is indeed stronger to use red bricks, but now many places do not sell red bricks.

I think it is a very good light brick, the quality of this brick is very lightweight, and it is very good to use, the price is cheap, the warmth effect is also very good, although the red brick is more strong, but the performance is not particularly good in other aspects.

Personally, I think it's better to lightweight bricks, because they are safer and won't hurt people. It seems that the red brick is indeed a little stronger.

1.What is the difference between lightweight brick and red brick?

1.There are some differences in performance between lightweight bricks and red bricks. Both have very good sound and heat insulation. However, in terms of load-bearing effect, the dead weight of red bricks is obviously heavier than that of light bricks, so the bearing capacity of red bricks is greater than that of light bricks.

2.Both lightweight bricks and red bricks have a tiny pores inside, and there is a certain difference in the bearing capacity of the two. If it is used for indoor masonry, it is better not to use lightweight bricks, because lightweight bricks are not as strong and hardness as red bricks.

3.There is a certain difference in the environmental performance of red bricks and lightweight bricks. Lightweight bricks are a very environmentally friendly material that does not cause much pollution during production and transportation.

The main material of red brick is clay, which is very easy to cause potholes in the ground. Moreover, red bricks will also cause a lot of air pollution during the firing process.

Judging from the raw materials of bricks, the hardness of red bricks is higher than that of light bricks.

Walls built with red bricks will be stronger than walls made of light bricks, but large-scale red brick high-rise residential buildings are forbidden in our country due to the very heavy net weight. If every homeowner is free to use the house, who will bear the responsibility if something goes wrong? The walls were built with little bearing capacity, the wooden floors were supported by concrete columns and beams, and the new walls were only filled with material.

As far as the whole house is concerned, you're more or less good.

From the perspective of national industry standards again, residential building codes.

Above the home improvement norms, the house is built with lightweight bricks, so why shouldn't we interior decoration? Decorative design: The place where red brick is applied at home is the bag pipe and side beam, and the bathroom wall is regarded as an application, and it is enough to apply lightweight bricks elsewhere. It is not clear who invented the treatment of building a layer of light bricks on top of two rows of red bricks.

No one has tested whether the wall is stronger than a wall made of lightweight bricks. Why do people say it's a better way to build walls?

Scared away. If you want to see a wall, there are many ways you can look for it online. In order to attract people's attention, take out the air to clean the mobile phone, open the national industry standard, this specification is the result of experts and scholars according to the data information, this specification has authenticity, and it is not easy to build according to this standard.

Red bricks are also known as gangue sintered bricks (commonly known as red bricks). Red bricks should be clay, diabase.

And coal gangue bricks are commonly used materials, through crushing, mixing and pinching, using artificial or equipment to inhibit, at a temperature of about 900 degrees of air oxidation flame, caused by calcined building bricks. The red brick production process is relatively simple, can be manufactured by machinery and equipment, with high production efficiency and wide application, due to the selection of hollow bricks.

Manufacturing, red bricks have the characteristics of moisture-proof, not afraid of moisture, and good fire resistance. Many of the early engineering buildings were made entirely of brick and concrete.

building structures, so they are often built with red bricks, but contemporary high-rise residential frame structures.

The house also has a lot of flaws.

It is better to use lightweight bricks, because red bricks are heavy, lightweight bricks, high strength, light weight, can be used for most walls of non-load-bearing structures, and have good thermal insulation and sound insulation effects.

It must be red bricks, because it is stronger, and it looks better, and it also has that kind of patriotism.

Generally, you choose to be lightweight, this kind of brick will make the space rate of the whole house larger, although the red brick is stronger, but it is a bit expensive.

Hello, you can choose to use lightweight bricks to decorate the interior partition wall. Lightweight bricks do not increase the gravity of the floor, as the porous sound insulation is also top-notch. Coupled with some special chemicals, it also has good fire performance, and it is a new generation of all-round products, which can not only meet the decoration requirements, but also reduce the waste of resources.

Due to the use of fly ash and gravel as raw materials, the shrinkage value of lightweight bricks is small, which ensures that the wall will not crack. Moreover, lightweight bricks are porous structures that have a significant impact on permeability. Lightweight bricks are environmentally friendly, shock-resistant, fire-resistant, durable, and easy to process.

Lightweight bricks can increase the usable area, and at the same time, due to the aerated concrete insulation, the insulation effect is good. The introduction of lightweight bricks used in decoration is as follows: lightweight bricks have good construction performance, convenient and simple construction, because of the large block and light weight, it can reduce the labor intensity of workers, improve construction efficiency and shorten the construction period.

The standard bricks are clay sintered red bricks, the standard brick size: 115mm*240mm*53mm, there are also gray bricks of the same size. Lightweight bricks are relatively light, aerated concrete blocks, the strength of bricks is not high, lightweight bricks can be broken, but the plastering strength is still very good.

In addition, the thermal insulation effect of lightweight bricks is good, and the thermal insulation effect of lightweight bricks is 5 times that of sticky leather bricks and 10 times that of ordinary concrete bricks.

The use of lightweight brick walls in rural housing should pay attention to the key points:

1. The mortar mix ratio is not accurate, and the cement and sand should be weighed. Measurement should be accurate. The stirring time should be guaranteed to meet the specified requirements.

2. Mortar without cement shall not be used in winter.

3. The three-seven wall must be double-sided and the two-four wall must be hung with backhand; The ash of the tongue should be scraped with the masonry.

4. Horizontal ash joints: the ash joints should be evenly mastered at the corners, each layer of bricks should be level with the leather number rods, and the pull line should be tightened. When masonry, it is necessary to take care of the left and right to avoid uneven joints.

5. Leather number rod: be careful and careful when copying and laying off the line, and the wooden stake of nailing the skin number rod should be firm to prevent collision and loosening. After the pith rod is erected, a horizontal elevation re-inspection should be carried out to ensure that the height of the pirate rod is consistent.

6. The position of the tie bar embedded in the masonry is not accurate: attention should be paid to the position indicated by the skin number rod of the masonry at any time, and the exposed part shall not be arbitrarily bent in the construction, and its length shall be guaranteed to meet the requirements of the drawings.

7. Liucha: The corners and junctions of the masonry should be masonry at the same time, otherwise it should be masonry.

8. Structural masonry: The brick wall of the structural column should be built into a large horse tooth, and the tie bar should be set up from the foot of the column on both sides should be retreated and then advanced, and the floor ash and brick slag debris in the structural column should be cleaned up to prevent slag inclusion.

9. Mortar strength: pay attention not to use expired cement, measure accurately, ensure the mixing time, and the production, maintenance and pressure test of the mortar test block should meet the regulations.

10. The top surface of the wall is not straight: the hollow brick wall is not good to pull the line when it is built to the top, and the wall is easy to go in and out of the uneven line.

11. Hollow brick wall chiseling: holes and embedded parts should be accurately reserved or buried according to the location, elevation and size of the design drawings, so as to avoid chiseling and opening holes afterwards and affecting the quality.

12. The tie bar does not fit the brick row: the embedded tie bar in the concrete wall column often does not coincide with the ash joint of the hollow brick row, and the brick row modulus should be calculated in advance to ensure that the tie bar is consistent with the hollow brick row, and the tie bar should not be bent and used.

13. Attention should be paid to the protection of the tie bar in the wall and column when it is bent or cut off.

The ingredients are different:

Lightweight bricks: high-quality tabular corundum and mullite are used as aggregates for strength products, with sillimanite composite as the matrix, and special additives and a small amount of rare earth oxide mixed torches are added, which are formed under high pressure and fired at high temperature.

Red brick partition wall: a sintered building brick made of clay, shale, gangue and other raw materials, which has been crushed, mixed and refined by manual or mechanical pressing, and dried at a temperature of 900 degrees Celsius and fired by an oxidation flame.

Lightweight bricks are mostly used now:

Lightweight bricks have aerated concrete blocks, light aggregate concrete blocks, ceramsite concrete blocks and other light blocks, which have the characteristics of heat preservation, sound absorption, light quality, etc., and are suitable for use in the construction of secondary structure masonry and indoor partition walls. There is no need to worry about the firmness, and now the walls in the concrete frame structure are made of the above-mentioned lightweight blocks.

In the mandatory provisions of construction works, it has been expressly prohibited to use red machine bricks as masonry materials, because it is made of clay and should be considered from environmental protection and other aspects.

Lightweight brick partition walls.

Red brick partition wall.

Lightweight brick partition walls and red brick partition walls have their own advantages and disadvantages, the differences are:

Lightweight brick advantages:

The weight is very light, the load-bearing pressure of the house can be reduced a lot, and the structure of the house is not easy to deform.

2.The sound insulation effect is better, and it is more economical and cost-effective while increasing the usable area.

3.No need to paint, after using special binder masonry, the flatness is better, you can do not need to do painting, which can save the next part of the cost.

Lightweight brick disadvantages:

1.If you build a house by yourself, the amount of money will not be much, and there are relatively few factories and homes, so the freight will be relatively high.

2.Poor secondary utilization. The overall strength of the wall is formed after masonry, and the bricks are not very reusable after dismantling.

3.The strength of lightweight bricks is relatively poor, and it can be broken with one punch.

Advantages of red bricks:

After the bricks are built, you only need to apply putty on top to create the same effect as the rest of the walls of the house, which is conducive to the overall beauty of the house. (njhongniu decoration).

The partition wall made of red bricks is stronger and the sound insulation effect is also very good.

Disadvantages of red bricks:

Relatively high;

It also occupies a relatively large amount of space, which will reduce the usable area of the house.

Gypsum board partition wall refers to the wall with gypsum board as a closed wall, and it is also a kind of "lightweight partition wall".

Lightweight partition wall, which includes gypsum board partition wall, cement board partition wall, lightweight block brick partition wall, etc.

If it is good, it is still good brickwork, and the sound insulation effect is good, but the construction is troublesome, and it is also troublesome when it is dismantled in the future, if it is a short-term partition, it is not recommended to use this method. The construction of light steel keel gypsum board is convenient, but the sound insulation effect is slightly worse.

Gypsum board is a material made of building gypsum as the main raw material. It is a kind of building material with light weight, high strength, thin thickness, convenient processing, sound insulation, heat insulation and fire resistance, etc., and is one of the new lightweight boards that are currently focused on development. Gypsum board has been widely used in the interior partition walls of various buildings such as residences, office buildings, shops, hotels and industrial plants, wall cladding panels (instead of wall plastering layers), ceilings, sound-absorbing panels, ground base panels and various decorative panels.

The gypsum board produced in China mainly includes: paper gypsum board, decorative gypsum board, gypsum hollow strip board, fiber gypsum board, gypsum sound-absorbing board, positioning point gypsum board, etc.