Should you use red bricks or light bricks as the material for building walls? Is it stronger to use

Judging from the raw materials of bricks, the hardness of red bricks is higher than that of light bricks.

Walls built with red bricks will be stronger than walls made of light bricks, but large-scale red brick high-rise residential buildings are forbidden in our country due to the very heavy net weight. If every homeowner is free to use the house, who will bear the responsibility if something goes wrong? The walls were built with little bearing capacity, the wooden floors were supported by concrete columns and beams, and the new walls were only filled with material.

As far as the whole house is concerned, you're more or less good.

From the perspective of national industry standards again, residential building codes.

Above the home improvement norms, the house is built with lightweight bricks, so why shouldn't we interior decoration? Decorative design: The place where red brick is applied at home is the bag pipe and side beam, and the bathroom wall is regarded as an application, and it is enough to apply lightweight bricks elsewhere. It is not clear who invented the treatment of building a layer of light bricks on top of two rows of red bricks.

No one has tested whether the wall is stronger than a wall made of lightweight bricks. Why do people say it's a better way to build walls?

Scared away. If you want to see a wall, there are many ways you can look for it online. In order to attract people's attention, take out the air to clean the mobile phone, open the national industry standard, this specification is the result of experts and scholars according to the data information, this specification has authenticity, and it is not easy to build according to this standard.

Red bricks are also known as gangue sintered bricks (commonly known as red bricks). Red bricks should be clay, diabase.

And coal gangue bricks are commonly used materials, through crushing, mixing and pinching, using artificial or equipment to inhibit, at a temperature of about 900 degrees of air oxidation flame, caused by calcined building bricks. The red brick production process is relatively simple, can be manufactured by machinery and equipment, with high production efficiency and wide application, due to the selection of hollow bricks.

Manufacturing, red bricks have the characteristics of moisture-proof, not afraid of moisture, and good fire resistance. Many of the early engineering buildings were made entirely of brick and concrete.

building structures, so they are often built with red bricks, but contemporary high-rise residential frame structures.

The house also has a lot of flaws.

It is better to use lightweight bricks, because red bricks are heavy, lightweight bricks, high strength, light weight, can be used for most walls of non-load-bearing structures, and have good thermal insulation and sound insulation effects.

It must be red bricks, because it is stronger, and it looks better, and it also has that kind of patriotism.

Generally, you choose to be lightweight, this kind of brick will make the space rate of the whole house larger, although the red brick is stronger, but it is a bit expensive.

If you look at the material of bricks, the density of red bricks is higher than that of light bricks.

Walls built with red brick will be stronger than walls made of light brick, but in high-rise buildings with large areas of red brick.

, the state prohibits its use because of the heavy weight. If every homeowner is free to use the house, who will be responsible in case something goes wrong? The walls we built had little bearing capacity, the floors were supported by concrete columns and beams, and the new walls were just fillers.

As far as the whole house is concerned, you are more or less fine.

<> again from the national standard, the building standard is higher than the home decoration standard, and the house is built with lightweight bricks, so why can't we decorate? The place where the decorative red brick is used at home is the bagged pipe and the bottom beam, the toilet wall is considered to be used, and the use of lightweight bricks elsewhere is sufficient. It is not known who invented the practice of building a layer of light bricks in two rows of red bricks in turn.

No one has tested whether this wall is stronger than a wall made of lightweight bricks. Why do people say it's a better way to build a wall?

Now a lot of homeowners are scared away by these ** on the internet. If you want to see a wall, you can find many ways on the internet. This is to attract attention, to take out the effort to scrub the phone, to open the national standards, these standards are the conclusions of experts through data, these standards are credible, and there will be no problem in building according to these standards.

Red bricks are also known as solid clay bricks (referred to as red bricks). Red bricks are made of clay, shale and gangue.

It is the main material, which is crushed, stirred and kneaded, and pressed manually or mechanically at an oxidizing flame temperature of about 900 degrees.

Below, it is made of sintered building bricks. The production process of red bricks is relatively simple, can be manufactured by machinery, has high production efficiency and is widely used, because of the use of solid brick production, red bricks have the characteristics of waterproof, not afraid of moisture, and good thermal insulation performance. Many of the early buildings were brick and concrete structures.

So they are always built with red bricks, but modern high-rise frame structures.

Houses also have a number of drawbacks.

It is better to use red bricks, red bricks are not easy to crack, the waterproof effect is particularly good, the load-bearing properties of red bricks are particularly good, very stable, it is indeed stronger to use red bricks, but now many places do not sell red bricks.

I think it is a very good light brick, the quality of this brick is very lightweight, and it is very good to use, the price is cheap, the warmth effect is also very good, although the red brick is more strong, but the performance is not particularly good in other aspects.

Personally, I think it's better to lightweight bricks, because they are safer and won't hurt people. It seems that the red brick is indeed a little stronger.

Hello, you can choose to use lightweight bricks to decorate the interior partition wall. Lightweight bricks do not increase the gravity of the floor, as the porous sound insulation is also top-notch. Coupled with some special chemicals, it also has good fire performance, and it is a new generation of all-round products, which can not only meet the decoration requirements, but also reduce the waste of resources.

Due to the use of fly ash and gravel as raw materials, the shrinkage value of lightweight bricks is small, which ensures that the wall will not crack. Moreover, lightweight bricks are porous structures that have a significant impact on permeability. Lightweight bricks are environmentally friendly, shock-resistant, fire-resistant, durable, and easy to process.

Lightweight bricks can increase the usable area, and at the same time, due to the aerated concrete insulation, the insulation effect is good. The introduction of lightweight bricks used in decoration is as follows: lightweight bricks have good construction performance, convenient and simple construction, because of the large block and light weight, it can reduce the labor intensity of workers, improve construction efficiency and shorten the construction period.

The standard bricks are clay sintered red bricks, the standard brick size: 115mm*240mm*53mm, there are also gray bricks of the same size. Lightweight bricks are relatively light, aerated concrete blocks, the strength of bricks is not high, lightweight bricks can be broken, but the plastering strength is still very good.

In addition, the thermal insulation effect of lightweight bricks is good, and the thermal insulation effect of lightweight bricks is 5 times that of sticky leather bricks and 10 times that of ordinary concrete bricks.

The use of lightweight brick walls in rural housing should pay attention to the key points:

1. The mortar mix ratio is not accurate, and the cement and sand should be weighed. Measurement should be accurate. The stirring time should be guaranteed to meet the specified requirements.

2. Mortar without cement shall not be used in winter.

3. The three-seven wall must be double-sided and the two-four wall must be hung with backhand; The ash of the tongue should be scraped with the masonry.

4. Horizontal ash joints: the ash joints should be evenly mastered at the corners, each layer of bricks should be level with the leather number rods, and the pull line should be tightened. When masonry, it is necessary to take care of the left and right to avoid uneven joints.

5. Leather number rod: be careful and careful when copying and laying off the line, and the wooden stake of nailing the skin number rod should be firm to prevent collision and loosening. After the pith rod is erected, a horizontal elevation re-inspection should be carried out to ensure that the height of the pirate rod is consistent.

6. The position of the tie bar embedded in the masonry is not accurate: attention should be paid to the position indicated by the skin number rod of the masonry at any time, and the exposed part shall not be arbitrarily bent in the construction, and its length shall be guaranteed to meet the requirements of the drawings.

7. Liucha: The corners and junctions of the masonry should be masonry at the same time, otherwise it should be masonry.

8. Structural masonry: The brick wall of the structural column should be built into a large horse tooth, and the tie bar should be set up from the foot of the column on both sides should be retreated and then advanced, and the floor ash and brick slag debris in the structural column should be cleaned up to prevent slag inclusion.

9. Mortar strength: pay attention not to use expired cement, measure accurately, ensure the mixing time, and the production, maintenance and pressure test of the mortar test block should meet the regulations.

10. The top surface of the wall is not straight: the hollow brick wall is not good to pull the line when it is built to the top, and the wall is easy to go in and out of the uneven line.

11. Hollow brick wall chiseling: holes and embedded parts should be accurately reserved or buried according to the location, elevation and size of the design drawings, so as to avoid chiseling and opening holes afterwards and affecting the quality.

12. The tie bar does not fit the brick row: the embedded tie bar in the concrete wall column often does not coincide with the ash joint of the hollow brick row, and the brick row modulus should be calculated in advance to ensure that the tie bar is consistent with the hollow brick row, and the tie bar should not be bent and used.

13. Attention should be paid to the protection of the tie bar in the wall and column when it is bent or cut off.

From a safety point of view, light bricks are generally used for home decoration partition walls. Even if you choose red bricks for the sake of a strong partition wall in the living room, the property will not agree. In fact, lightweight brick partition walls are already a common practice in the industry, and the firmness is not bad compared with red brick walls.

There are many varieties of light bricks, by reducing the area occupied by the material, increasing the holes and gaps, reducing the weight and improving the strength of the product, the use is very wide, generally there are clay hollow bricks, clay porous bricks, concrete hollow bricks, ceramsite bricks and other new wall materials.

Compared with red bricks, light bricks have quite a lot of advantages as partition wall materials. If you don't believe it, Bai Gong will count it for you:

The heat retention of lightweight bricks is very good. When the lightweight brick is used as the peripheral decoration structure, it can meet the requirements of thermal insulation and energy saving without auxiliary insulation materials, and the insulation effect of 24 brick walls can be achieved with lightweight wall tiles with a thickness of 4cm, providing a comfortable and comfortable family living environment.

More impermeable than red bricks. The internal structure of the light brick is evenly closed, which effectively prevents the diffusion of water molecules, and the impermeability is 85% higher than that of sintered clay red brick masonry when the exterior wall is painted for home decoration.

From the perspective of fire protection, the fire resistance of lightweight bricks is very good. The raw materials and products of light bricks are inorganic, which is an ideal fireproof material, and the fireproof capacity of the new wall with a thickness of 100m reaches more than 4 hours, which can be used for firewall engineering;

Compared with red brick walls, lightweight bricks are more sound-absorbing and have good sound insulation. According to tests, lightweight brick walls can insulate 30-50 decibels.

Therefore, there are many advantages to building walls with lightweight bricks. Although it looks light and fluttering and the weak wind looks, the strength is not as high as the red brick, but the strength can be significantly improved after the plastering of the wall, coupled with the advantages of sound insulation, heat preservation, fire prevention, etc., now use the light brick as the material of the partition wall, and its effect and cost advantage are obvious. There is no one to build partition walls with red bricks anymore.

Bathroom walls are generally made of red bricks. Compared with lightweight bricks, red bricks are dense, not easy to enter water, not easy to deform, have better water insulation, and are more suitable for toilet use.

Can lightweight bricks be used as sanitary partition walls?

Lightweight bricks should not be used as sanitary partition walls, because lightweight bricks are not waterproof. If you want to use lightweight bricks to partition the wall, you need to hang a steel wire mesh on the partition wall, then paint it and apply waterproof paint before you do it. Lightweight bricks can be used to build brick walls, it can be used indoors, and in the case of partition walls, the floor will not be loaded, and it can also play a role in sound insulation.

However, it is not very convenient to use in the kitchen and bathroom.

What are the advantages of lightweight bricks?

1. Lightweight bricks can be used on the exterior wall structure, and it can play a role in thermal insulation without increasing insulation materials. If you use it in the case of a search hand, it is very comfortable in the home. And the internal structure of lightweight bricks is particularly uniform, which can avoid the phenomenon of water diffusion.

Moreover, when painted as an exterior wall in a home, its impermeability is higher than that of clay red brick masonry.

2. And the fireproof effect of lightweight bricks is particularly good. If a 100-meter-thick lightweight brick wall can be fire-resistant for more than 4 hours, it can be used as a firewall. and soundproofing of lightweight bricks.

Able to reach about 30 to 50 decibels, it is a particularly good material for absorbing false sound.

What are the uses of lightweight bricks?

The leak-proof effect of lightweight bricks is particularly good, and its range of use is also relatively wide. In the summer, it can insulate the outdoor heat. Lightweight bricks can be used not only in homes, but also in large quantities in cities.

And it can reduce the overall cost of the building.

<> "Generally use red bricks, because the material of red bricks will be more solid than light bricks, and it is less prone to water ingress and deformation, and the water absorption rate will be lower than that of light bricks, so red bricks will be more suitable for building bathroom walls, and the waterproofness of lightweight bricks is worse, and it is also prone to deformation, once the lightweight bricks are deformed, they are easy to crack and leak, which affects the waterproof effect and stability of the wall.

Lightweight bricks are not suitable for masonry bathroom and kitchen walls, because under normal circumstances, lightweight bricks are only suitable for masonry indoor partition walls that need to be waterproofed, which can not only effectively reduce the load of the floor, but also play a good sound insulation effect. If you must use lightweight bricks to build the bathroom wall, you must hang a net on the wall for plastering construction, and after the plastering construction is completed, you must also paint waterproof paint on the wall.

Second, what should be paid attention to when building the bathroom wall with red bricks.

1. In the process of masonry, we must strictly control the thickness of the masonry of the wall, if the house is a self-built house, then the thickness of the bathroom wall is best set at about 240 mm, if it is an ordinary commercial house, then the wall thickness is generally only 150 mm.

2. After the completion of the masonry pants of the bathroom wall, the surface of the bathroom wall should also be plastered for construction, in order to strengthen the firmness and stability of the wall, effectively avoid cracking and leakage of the wall, before the plastering construction, it is best to carry out the net treatment, after hanging the net, and then carry out the plastering construction, and then paint the waterproof coating, and finally pave the tiles, these sequences can not be wrong, so as to avoid affecting the construction effect.