Can the old wall be strong if it is directly glued to the tile?

Yes, but the premise is that the old wall needs to be treated on the surface, there can be no oil, impurities, floating dust, etc., and on the old wall to brush a layer of glue, brush a layer of glue on the surface of the tile, and leave it horizontally for about 10-20 minutes. The adhesive should also be applied thin on the back of the new tile, and the thickness should be subject to the back pattern of the covered tile, so that the new tile will be more firmly glued. When paving new tiles, use a rubber hammer to tap the new tile edge to adjust the edge, you need to pay attention to the reserved expansion joint, 24 hours later, wait for the tile adhesive to dry thoroughly, and use the grout to hook the joint.

Tips: Individual seriously bulging or damaged tiles need to be removed, after shoveling, repair with mosaic surface tile surface treatment agent, and after the surface of the old tile is as smooth as the old tile, then paste the new tile with tile adhesive, which is more firm.

As we all know, cement mortar is generally used for tiling, but in recent years, there have been more tile adhesives on the market, and I don't know which one is better to use!

Let's look at the cement mortar first, that is, it is mainly cement, add yellow sand and some waterproof additives, and then stir with water, which is basically zero pollution, high adhesion, and preferential treatment.

But the bad thing is that cement mortar is affected by many external factors and is easy to fall off. In addition, the hardness of tiles on the market is getting higher and higher, and the focus is on poor water absorption, so the tiles often fall off.

From the appearance, tile adhesive and cement are almost the same, mainly mixed with water, and then directly used to paste tiles. However, tile adhesive has an advantage that cement does not have, that is, it is less affected by external factors, and it is resistant to low temperature and water. The bad point may be that it is expensive, and there are many bad tile adhesives on the market, and there may even be the problem of excessive formaldehyde.

Compared with cement and tile adhesive, the adhesive performance of ceramic tile adhesive will be better, the point is that you don't need to run the tile in advance, you can paste it directly. There is no need to paint a thick layer on the wall, and it is basically very firm when pasted on.

Of course, good things are generally expensive, so there is no need to use tile adhesive in all places, you can use it in the kitchen and bathroom, because these places are often wet, and it is easy to fall off with general cement.

Use tile adhesive.

Yes, but it is not recommended to do so in actual construction, because the surface of the tile is very smooth, and it is not easy to stick it firmly when the tile is pasted; In addition, whether the original tile is firmly attached remains to be investigated, and then the tile will increase the load of the original tile adhesive layer, increase the gravity of the brick and the possibility of occurrence. When we pave tiles, we should hang wires on the wall and ground to confirm the height of the tile paste, so we are less likely to have uneven tiles when paving tiles. When laying tiles, pay attention to leveling with a ruler, if there are raised tiles, you can use a rubber hammer to knock on the surface of the tiles.

<> in order to reduce the hollowing of the tiles.

Rate, users may wish to soak the tiles in advance, before laying the tiles, dry them in a dark place. Tiles that have been soaked in water can not be dried, otherwise it is still easy to cause tile hollowing. Or you can use tile adhesive to pave, this glue has a good adhesive ability, and at the same time resistant to moisture and low temperature, it can stick the tiles firmly.

Whether you are laying tiles or laying ground materials such as wooden floors, the ground must be leveled before construction, otherwise there will be tile inequality. When laying tiles, you can use special tools to separate the gaps of the tiles, otherwise the gaps of the tiles are too small, the tiles will expand after heating, and they will shrink when they are cold, causing problems such as hollowing and falling off.

The most important thing is to re-lay the new bricks on the old floor tiles, this method is only suitable for houses where the previous ground base layer was relatively good and the house is not very old. If there is different degrees of water seepage and falling off on the ground, it is necessary to remove the original tiles and waterproofing in advance, and retreat the base layer. Finally, for the newly painted wall, in principle, tile adhesive can also be used to pave the tile, but for the old painted wall, the topcoat and putty must be removed in advance.

layer, to be cemented mortar.

After the layer is exposed, it can be treated with a surface treatment agent for the face brick, and the tile adhesive is used to paste the brick again. In addition, since laying new bricks on the old floor tiles is not a simple matter, it is necessary to find a reliable professional construction personnel to undertake it, so as not to cause unnecessary trouble in the later stage.

Definitely not, such an operation is meaningless, and it will also lead to serious damage to the wall, which may cause the original tiles to fall off.

It is impossible, even if it is pasted now, it will fall off after a while, so that the damage to the tile and the front is very large, and it is not recommended to have such an operation.

1.Old tile walls can be used tile glue, and then tiled. Can be glued with tile glue. It is a special glue for smooth tiles, and the bonding strength is also very good. Porcelain glue, also known as adhesive.

clay, etc. It is a new type of modern decorative material that replaces the traditional cement sand. Adhesion is cement mortar.

Several times, it can effectively paste all kinds of stone and avoid the risk of tiles falling off. Can be glued with tile glue. It is a special glue for smooth tiles, and the bonding strength is also very good.

Porcelain glue, also known as adhesives, clay, etc. It is a new type of modern decorative material that replaces the traditional cement sand.

2.The adhesion is several times that of cement mortar, which can effectively paste all kinds of stone and avoid the risk of tile falling off. If you don't want to break it up and repaint it at this time, it is recommended to use special enamel paint to paint and beautify the tile to restore the luster and smoothness of the tile in the past.

However, it is important to avoid painting the gaps in the wall so as not to affect the overall appearance. After the wall adhesive is completely dry, the next process can be carried out. Before laying the tile, it needs to be blistered, so that the tile can absorb enough moisture and no longer blister, so as to prevent the tile from absorbing the moisture in the cement mortar, so that the tiles will not fall off.

3.At the same time as shoveling off the tiles, the cement mortar layer of the tiles is also shoveled clean, and the base layer is cleaned. Follow the renovation process.

From bottom to top, from left to right, the overall tile paving effect is good. Once the tiles have cured and dried thoroughly, use caulk to evenly distribute the gaps in the tiles.

For freshly painted walls, in principle, it is also possible to lay tiles with tile adhesives. But for old whitewashed walls, it is necessary to remove the topcoat and putty in advance.

layer, after the cement mortar layer is exposed, it can be treated with tile surface treatment agent, and finally paste the tile with tile adhesive.

4.Due to the tiles in the old floor.

It is not a simple matter to lay new bricks, so be sure to find a reliable and professional construction party to do it, so as not to cause unnecessary trouble in the later stage. The requirements for flatness are not high, but the requirements for glue are: durable and firm. Construction glue, marble glue.

Glass glue, cement. Their requirements for the base layer are different, such as glass glue with glossy surface, and other textured surfaces, all of which must be dust-free. Prevent collapse during installation. The reflective adhesive does not collapse.

No; Because there will be a lot of oil stains and impurities on the old tiles, if you directly use tile adhesive to paste the tiles, it will cause the tiles to be not firmly pasted, or to shovel off the old ones, and then do a good job of the base and then paste them again, so that the tiles can be well pasted and can also reduce the cost.

No. Because the way of sticking tiles in this way is not firm, it will fall off in the later stage, and it will also affect the appearance.

No, as this will affect the overall effect and may cause the tiles to be very uneven.

Stick the wall tiles directly with tile glue, pro! Hello, I am very happy to answer for you<> you can directly use tile adhesive for wall tiles 1, tile adhesive for ceramic tiles, which has great viscosity, waterproof, anti-aging, convenient construction and other advantages. 2. Before pasting tile adhesive, clean up the dust stains on the surface of the original tile.

3. Then evenly brush the tile adhesive on the surface of the original tile, and then evenly apply the tile adhesive on the back of the new tile. 4. Press the new tile on the old tile and gently tap it with a rubber hammer to ensure that it remains sticky. 2. What are the precautions for tiling 1. Before paving the tiles, the base surface must be soaked in advance until there is no blistering.

And clean up the base surface in time to ensure that the base surface is kept clean, no hollowing, and the flatness is up to standard, and only after the strength reaches the standard can the follow-up brick arrangement, elastic line, paving and other work be done. 2. When the construction is formally paved with tiles, it is necessary to pay attention to the drainage slope to avoid water accumulation. Moreover, when tiling and paving, it is necessary to pay attention not to damage the original waterproof layer, otherwise the waterproof problem will be re-treated.

When pasting tiles, the cement mortar should be evenly applied to the back of the tiles to exhaust the excess mortar and the bottom air. Moreover, when laying tiles, expand joints are reserved to avoid hollowing of tiles in the later stage. 3. After 1 hour of ceramic tile paving, the dirt on the tile should be cleaned up first, so that it can be cured naturally, the temperature is relatively high in summer, and you can walk after 24 hours of paving, the temperature is low in winter, and the curing time can be extended appropriately, when the coagulation strength of the mortar reaches the standard.

Hope mine can help you <>

Do you have any other questions?

Hello dear. If you stick all the tiles on the wall with cement and cement, it will fall off for a long time. Now the all-ceramic tile due to the hard texture, does not absorb water, attached to the wall sail is not easy to close with the cement structure, a long time will fall down, if it falls down not only affects the appearance, but also affects the safety, has to prevent.

The common causes of the type are as follows: There is a problem with the mixing ratio, resulting in the adhesion force cannot meet the requirements; 2.The quality of the tile is better, the water absorption rate is reduced, and the difficulty of bonding increases when the size increases, and the cement strength does not meet the requirements; 3.

The porcelain cracked bricks are not soaked in enough water, or the wall surface is not sprinkled with water, and the wall tiles are not fixed and supported after they are paved; 4.The quality of the cement used is defective, the label is too low or it has been opened for too long and has expired; 5.When paving, the thickness of the cement is not up to standard, and it cannot meet the requirements of adhesion force; 6. The wall is not clean and rough cement, with white ash or lightening.

Dear, <>

The above is the answer I summarized for you, I am very happy to serve you, please give me a thumbs up, thank you very much for your <>

Hope mine is helpful to you.

Stick all the tiles on the wall with cement and cement, and if you stick them for a long time, they will yard and fall off.

Now all-ceramic tiles due to the hard texture, do not absorb water, late liquid staring on the wall is not easy to stick with the cement structure, a long time on the buried pin will fall down, if it falls down not only affects the appearance, but also affects the safety, has to prevent. Common causes are as follows:

There is a problem with the blending ratio, resulting in the adhesion force cannot meet the requirements;

2.The quality of the tile is better, the water absorption rate is reduced, and the difficulty of bonding increases when the size increases, and the cement strength does not meet the requirements;

3.The tiles are not soaked in enough water, or the wall is not sprinkled with water, and the wall tiles are not fixed and supported after they are paved;

4.The quality of the cement used is defective, the label is too low or it has been opened for too long and has expired;

5.When paving, the thickness of the cement is not up to standard, and it cannot meet the requirements of adhesion force;

6. The wall is not clean and rough cement, with white ash or lightening.

Dear friends, what kind of glue should be used to put the marble bricks on the wall so that they will not fall off for a long time.

dao My workers replied like a superglue.

tile adhesive.

When using, you only need to apply a layer of glue on the wall and the back of the tile, wait for a few minutes, touch the glue surface with your hands, if the glue surface is not sticky, you can stick the tile on the wall and compact.

Tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, grounds, bathrooms, kitchens and other building finishing decoration places.

Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material.

Tile adhesive has many advantages, such as the use of tile adhesive can save more space than the use of cement, and only a thin layer of tile adhesive is OK. If the construction process is up to standard, the tile is very firm; It can also reduce waste, no toxic additives, and meet environmental requirements.

Tile peeling off can be pasted back with tile adhesive, the current market is divided into ordinary tile adhesive, reinforced tile adhesive and heavy brick tile adhesive, different tile adhesive its construction requirements are also different, so when using it must be clearly understood.

1. Ordinary tile adhesive. Ordinary tile adhesive is a product that is more suitable for pasting various floor tiles or small bricks on the wall of ordinary mortar surface.

2. Reinforced tile adhesive. This kind of product has a relatively strong adhesion and anti-falling force, this product can be used to the adhesion requirements of the wall tile and non-mortar surface paste to play a good role, such as wood board is more suitable.

3. Heavy brick tile adhesive. This type of glue has a large adhesion force, and this product is also flexible, which can resist the stress caused by the thermal expansion and contraction of the adhesive layer, so it is more suitable for the pasting of various stone slabs with large areas such as gypsum board, fiberboard, plywood or old veneer. Adhesive is strong, more flexible, and can resist the stress caused by the thermal expansion and contraction of the adhesive layer, in addition to gray, tile adhesive can also provide a white appearance, suitable for light or translucent marble, tile and other natural stone.