After half a year of soaking tiles, it was found that there were several hollow and torn phenomena,

We first have to consider whether it is a problem of tile quality, and then we can know how to solve this thing, the reason why the tiles appear hollow and torn after half a year, may be the reason why the tiles are paved before the tiles are paved to do a good job of soaking water, so that each piece must be carried out in all directions, enough time to soak in water due to insufficient soaking water, then in this case, the tiles pasted to the wall will appear hollow and tear after 3 to 6 months.

The best thing to do is to remove the hollow and torn tiles and reattach them with new ones. The cost of this is not very large, and it does not pose a security threat.

It is recommended to remove the tiles from the position of the hollow drum first to avoid sudden falling off and causing injury. Then replace it with new tiles. Fixing with structural adhesive is fine.

1: tile soaking water is not sufficient, wall tiles are mostly ceramic tiles, this kind of tile is easy to absorb water, before paving to fully soak with water before paving, if the soaking is not sufficient, it will quickly absorb the moisture in the cement mortar, resulting in the cement mortar can not be well coagulated, thus causing the tile hollowing.

2: Cracking of the wall structure causes cracking of the tile. Due to the construction technical problems of the secondary structure wall in the decoration, there is no very strong connection with the main body, and the wall will crack after a long time, and the wall cracking will cause the tiles paved on the wall to be cracked.

3: The mixing ratio of cement mortar is not appropriate, when paving the quality tile, the mixing ratio of cement mortar used is incorrect, and there is more sand and less cement, so that it is easy to cause the cement mortar to be hollow due to insufficient solidification force. The cement is more sand and less sand, and it is easy to hang when paving, resulting in hollowing of tiles.

It may be that the effect of this tile is not too good, or it may be that the quality of the tile is not particularly good, so it will lead to hollowing and tearing.

If you need to re-repair, you must pay attention to the condition of the wall, pay attention to the falling off of the tile, and avoid serious problems with the tile.

The reason why the soaked tiles are found to be hollow and torn after half a year: because we first have to understand whether it is a problem with the quality of the tile, and then we can understand how to deal with this matter The floor tile occurs after half a year The wall is hollow and torn. The tiles that stick to the wall will hollow and tear after 3 to 6 months.

For the application of soaking bricks, it is necessary to ensure that the soaking bricks are carried out for a sufficient period of time before paving, so that each piece needs to be carried out in a multi-directional way to make tea for a sufficient time, and then the soaked floor tiles are taken out before paving, and the surface layer can be dried to the surface without flowing water. If there is no guarantee that the tiles will be soaked in water before the floor tiles, in other words, there is not enough time for water to enter the tiles, then the tiles on the wall will be hollowed out and torn after 3-6 months.

For the paving of soaking bricks to the wall, the paving raw material used is mixed mortar, but the mixed mortar is normally mixed evenly according to the ratio of 1:3. If there is a mistake in the proportion of cement slurry and the proportion of concrete is increased, then there is a probability that the soaked bricks will tear the floor tiles and accompany the hollowing of the wall due to the strong cement model.

For the soaking bricks paved on the wall, it is necessary to do immediate maintenance at the end of the paving, so that the mixed mortar of the paving can be quickly closed to ensure that everything is dried normally, so as to ensure the quality of the paving. If it is not sprinkled immediately, especially in the hot summer, there is no early sprinkling maintenance, then the soaking bricks will accelerate the digestion and absorption of the concrete in the mixed mortar, resulting in the quality of the floor tile parquet products, followed by the soaking bricks The wall is hollow and torn.

For the hollow tiles, you can take the hollow drum part as the center, break the hollow drum tile and one or two tiles around it, and then re-paste the tiles.

There is little remedy. You can only let the master bricklayer re-apply the bricks, and you must pay attention to the humidity and quantity of the cement, and do not empty the drum again.

In this case, the tiles should be lifted again, and then re-laid, and should also pay attention to the quality of the problem, please ask a more professional construction team to construct.

Then leave it alone, if you do, you'll have to smash that wall and re-stick it.

Summary. Hello dear! Glad for your question!

After the soaked tiles are pasted in the summer, some are hollow, some are not hollow, or the tile is still a problem, or a workmanship problem; As a soaking brick, if the back of the cloth is brushed clean and not sealed by the adhesive of the tile, it is generally pasted with cement and sand ash will fall off, which is mainly a tank that has been soaked in water, on the back of the tile, many small holes in the eyes have been. Dust impurities and other debris have been closed, so it is said that there will be a very thin film when bonding, although it can not be seen when brushing clean, but it still exists, so it is said that it is pasted with cement and sand ash, and it will fall off after a long time, and even after pasting dry, there will be a hollowing phenomenon, so if this kind of soaking brick is still used, it is recommended to use tile glue to paste, which will avoid the occurrence of this phenomenon.

After the soaked tiles are pasted in the summer, some are hollow, some are not hollow, or the tile is still a problem, or a workmanship problem;

Hello dear! Glad you had your questions! After the soaked tiles are pasted in the summer, there are empty drums of Lacha, and some are not empty, which is still a tile problem or a workmanship problem; As a soaking brick, if the back of the cloth is brushed clean and not sealed by the adhesive of the tile, it is generally pasted with cement and sand ash will fall off, which is mainly a tank that has been soaked in water, on the back of the tile, many small holes in the eyes have been.

Dust impurities and other debris have been closed, so there will be a very thin film when bonding, although the brush can not see the noise, but it still exists, so it is said that the cement and sand ash are pasted, and it will fall off after a long time, and even the hollowing phenomenon will occur after the paste is dry, so if this kind of soaking brick is still used, it is recommended to use tile adhesive to paste, which will avoid the occurrence of this phenomenon.

Hello dear! Glad you had your questions! After the soaked tiles are pasted in the summer, there are empty drums of Lacha, and some are not empty, which is still a tile problem or a workmanship problem; As a soaking brick, if the back of the cloth is brushed clean and not sealed by the adhesive of the tile, it is generally pasted with cement and sand ash will fall off, which is mainly a tank that has been soaked in water, on the back of the tile, many small holes in the eyes have been.

Dust impurities and other debris have been closed, so there will be a very thin film when bonding, although the brush can not see the noise, but it still exists, so it is said that the cement and sand ash are pasted, and it will fall off after a long time, and even the hollowing phenomenon will occur after the paste is dry, so if this kind of soaking brick is still used, it is recommended to use tile adhesive to paste, which will avoid the occurrence of this phenomenon.

Because of its beautiful and easy to care for the advantages of ceramic tiles, in our daily decoration, the use rate is very high, and the quality problems of paving tiles have become very common. Tiles will have cracks and hollows after a long time, if this is the case, we haven't remedied them? Here you will ask:

What remedy is used? Of course, there is a way, today I will share a remedy for you, I believe that after you see it, use such a trick to return your tiles to the previous luster.

First of all, the corner hollow: if you find that the edge of the tile is hollow, you can water the part of the edge hollow, smash the gap between the tiles with a small shovel, and then pour the cement with water into the gap, and the hollow drum will be automatically sucked in until it is filled and solidified, so as to avoid overall replacement.

Secondly, local hollowing: a small amount of local hollowing of the tiles on the wall and floor, without affecting the cabinets, mirror cabinets, cherry blossoms, showers and water heaters and other furniture and household appliances installed steadily, can not be treated, but if it affects the installation and daily life, it is recommended to knock off the local tiles and re-pavement.

Third, 2 3 area hollow drum: it is recommended to remove it and re-pave, at this time the adhesive used in the paving is particularly important, a single tile is pasted on a flat plane, hungry hands can use tile adhesive or tile paste, if it is a small area of multiple tiles, it is recommended to use Yi Glue Cement is more appropriate than the use of cement.

Fourth, there is a small trick for black cracks: you can use tile paste to fill in the obvious cracks, which plays a role in disguise and cover-up. This remedy should not be used immediately, and can be applied every hour or two.

How to deal with the hollowing of the tiles and the unevenness of the tiles during the decoration? In our usual life, decoration is very important, and in the process of decoration, tiling is the most basic work, of course, it is also the most important work, if the tile is not flat or hollow down, there are three main solutions:

1) Flattening with a heavy object.

Because most of the uneven tiles are cement that is not evenly smeared, at this time we can use heavy objects to flatten, in those difficult places, you can press buckets, bricks and other heavy objects in time before the cement is completely dry for one night, and it will generally improve a lot the next day.

2) Flatten the top with wooden strips.

If the tiles in our home are pasted, there are a lot of uneven places, and it is more serious, at this time it is recommended that we take advantage of the cement is not solidified, use some wooden dragons, one end against the uneven part of the tile on the ground, and one end on the roof of the house, which also has a certain effect.

3) Knock out all the tiles and replace them with new ones.

Since the tiles are not paved and the gaps are large, there is no need to repair them, because the number is not very large, so it is better for us to knock out the tiles again and replace them with new ones. The original poorly paved tiles are cut off with a cutter to prevent damage to other surrounding tiles, and then a few pieces of tiles of the same model from Olek are purchased and re-paved. If it was previously due to the worker's technology caused by the paving problem, then ask for free rework, if it is caused by the quality of the tile itself, then it is good to negotiate and solve.

These three methods above can be said to be the best way to solve the problem of tiles are not paved, of course, when laying tiles, we are best to do a good job with the master before paving is the best solution, tiles should be paved well, before paving should be noted:

1) When laying tiles, it is uniformly paved according to the bottom blank arrow; This allows for maximum control of tile unevenness and a smoother overall paving. Some manufacturers use the direction of letter sign paving, but you have to look carefully.

2) Leave joints to pave tiles; You know, in our daily life, even if the best tiles have a concave and convex qualification standard, the seam paving can not only weaken the concave and convex feeling, but also reduce the arch or cracking caused by the cold shrinkage and thermal expansion of the tiles in the future; Grouts can be used for grouting, which is both aesthetically pleasing and functional.

3) Divide the whole into parts and lay tiles; Select bricks with a small difference in unevenness and pavement next to each other, and cut the bricks that are really difficult to deal with into small pieces for use in the corners.

The above is all the solutions after the tile is uneven, although the tile is uneven, there are some remedies, but the problem of uneven tiles still requires us to be prepared in advance for such a problem. This is the only way to prevent problems during home inspections. Even if there is a master who can help us remedy, it is still time-consuming and laborious!

I don't know if you've learned?

It shows that the tiles inside are not very consistent, and at this time you should get up and re-paste the tiles, otherwise after the decoration, it will definitely fall off after a few years.

The best thing to do is to clean up where the tiles fell and reapply a new one.

At this time, I think you should buy some tile adhesive, and then re-stand this tile, or go to the previous decoration master **.

Hello dear! I'm here to answer your questions, and I'm glad you asked! What can be done to remedy the hollow tiles pasted; First, if the corner of the tile is hollow, if the corner of the wall is hollow, we must now shovel the gap around the tile, and then use relatively thin cement to pour and knock on the tile while pouring, so that the cement slurry can be completely penetrated.

This treatment saves time and effort, and is not easy to cause damage to the tiles. Second, the middle of the tile hollow drum tile in the middle of the hollow drum situation, this situation needs to pry down the tile and re-lay. Specifically, it is necessary to smash from the middle part of the tile, but not directly from the middle, you can use a small rhinestone to open a hole first, and then use a tool to slowly spread to the surrounding way to pry open the tile, to avoid damage to the surrounding tiles.

3. If there is a hollow drum in a large area of more than 1 3 pavement area, it is necessary to pry off all the tiles on the whole surface and re-pavement. Usually this large-area hollowing drum is caused by improper construction, and the construction party should bear the cost of tile damage and labor accessories. Fourth, if the hollow drum is more serious, the tile has been completely loosened or even falling off, indicating that the cement mortar layer under the tile and the wall base (or ground base) have also been loosened "delamination", at this time, you can use a shovel and other tools to clean up the cement mortar layer, re-apply the cement mortar and then pave the tile.