Car fender dent repair, how much does fender dent repair cost?

CarsFendersThe steps to repair the depression are as follows:

1. Sheet metal repair: mainly apply putty in the sunken places.

It is then smoothed and then touch-up is applied to the repaired area.

2. Traceless repair: Repair the sunken place to its original appearance without traces, which is relatively cheap.

The function of the fender is mainly to prevent small stones and sludge from splashing under the carriage, so as to protect the carriage and improve the service life of the vehicle to a certain extent.

Fender dent repair **300-500 or so, the step is to dig and repair and paint, this little injury insurance next year you will not have preferential treatment 4S shop is very expensive, estimated to be about 700.

If you are insured, it is less than 1,000 yuan. If you apply for insurance and go to a 4S shop, you don't need to care about it, like in our small car repair shop, 200 to 260 is about the same.

It depends on the model and where to repair, as well as the damage, according to the market ** on August 5, 2021From 300 yuan to 3000 yuan.

If there is only one fender, plus sheet metal and paint, the repair shop only needs about three or four hundred yuan, but the cost of working hours and materials in the 4S shop will be higher, and many models are only replaced without repair, ** will be higher.

Precautions for vehicle maintenance.

1. Don't park the broken car in the middle slope for maintenance.

Some car owners will park the broken car directly in the half-slope position for repair, and forget to pull the handbrake, and finally cause a serious accident. The correct way is that when the owner parkes, he should pay attention to whether the parking place is a slope, and it is best to find a flat place without a slope to park. Check that the car is still in gear and pull the handbrake.

If it is in a place with a slope, it is better to place an obstacle under the wheels to prevent the vehicle from sliding suddenly.

2. Warning signs must be placed on roadside maintenance vehicles.

Repairing a car on the side of the road is quite risky, and passing vehicles can pose a danger to you at any time. Therefore, when the owner repairs the car on the side of the road or waits for rescuers on the road, he must set up a warning sign about 50 meters behind the car. If there are no warning signs on the car, you can find some branches or obstacles around to mark them to warn the vehicles behind you to avoid traffic accidents.

Judging from the **, the iron sheet has leaked out, and you can only do sheet metal painting, otherwise it will rust. Sheet metal painting is about 400 to 600 on one side.

1. Look at the appearance damage from **: the right front fender, the right front bumper, and the surface of the right headlight have slight scratches (the right front fender seems to have been repaired before). It is necessary to disassemble and check whether there is any damage to the internal accessories, and the internal accessories may be damaged: right front guide, right front headlight seat.

2. If it is only repaired and does not involve the replacement of accessories, the cost of sheet metal painting in the repair shop is about 500 yuan, and the 4S shop is slightly more expensive.

3. If you want to replace the right front fender plus maintenance, it may be more than 1000 yuan, and the specific maintenance cost is recommended to go to the repair shop to find the maintenance master to disassemble and inspect it for you.

Hello. Judging from the **, your fenders are more damaged, and the paint has fallen off. And putty should have been scraped once. Traditional sheet metal repair will do. Or you have to spray paint after the dent is repaired.

For these different repair construction, in different regions, different models, the charges are different, generally depending on which part is the specific, how big the depression is, generally 100 to 400 yuan, or according to the specific situation to decide.

Hello, if I don't replace it, it's about 300.

Remove the rubber strip under the front windshield with a movable socket wrench and screwdriver, then remove the screws of the fender sequentially, and remove the liner of the fender after 20 minutes. The iron plate is not thick, do not use a hammer, otherwise it will backfire, use a small rubber hammer to cushion the cushion, otherwise it will damage the paint surface. There is no rubber mace, and the same goes for a towel wrapped in a stick.

After hammering, it takes 60 minutes to put it back in place. Remove the liner and use the tire as a fulcrum, make a small wooden block to clear the groove and carry the stick on it.

Pull out with a trimmer or electric suction cup. Find a paint shop for sheet metal spray paint. If there is a depression, sheet metal machining is required.

If the paint in the dent has been damaged, anyone who knows knows that it is difficult for technicians to find the point when repairing. The most important and crucial point in repairing dents is to find points. Not being able to find the point will only make the dent repair worse and worse.

Without extensive experience in repairing cars, technicians who are not as pure as fire can do nothing about this dent. Paint repair is also very technical, but it seems to be very unskilled.

Many car owners are getting worse and worse when spraying paint, because they don't know the skills of spray paint maintenance, the technician who has completed the painting can repair the damaged paint to 80%, and on the line where the paint falls, due to excessive pressure, the metal plate is folded into two ridges of nearly 90 degrees. Fixing these two ridges is not easy. The sharper the depression, the higher the requirements for finding points, and inaccurate finding will lead to obvious pitting after repair, which is a big challenge for technicians.

The area of the depression is the size of two palms. Such a large depression is very sharp, which not only takes a long time to repair, but also tests the patience of the technician. In the process of repairing car dents, there is a knack for fixing large dents.

As long as you find the self-pressure point and exert force after finding it, you can calm down about 50%. After that, the depression was decomposed and repaired. The large depression will break down into several small depressions, and the small depression will break down into smaller and smaller depressions.

Eventually, it will be broken down into an infinite number of points, each of which is little by little. The work after the dent repair is touch-up. Of course, not all dents need this step, only those that have lost some paint are necessary, and as long as it is the original paint, the possibility of paint falling off is very small.

There are two ways to repair it, one is sheet metal painting, and the other is dent and traceless repair. Sheet metal painting is the use of a machine to suck out the recessed part and restore the flattening. The dent without trace repair is purely manual repair by pulling, pulling and prying.

Fenders can now be repaired by sheet metal painting, and a more aesthetically pleasing way is a non-marking repair, which can be repaired by a dedicated technician.

Summary. Hello, I am your car master exclusive elite technician, I wish you a happy life and a prosperous Year of the Tiger. We promise to be attentive, careful and attentive to answer your car problems, and find solutions and solutions to the corresponding problems for you!

Hello, the left front fender depression repair of this modern famous map, if the depression is more serious, the repair cost is between 450 550, if it is a slight depression, the repair cost can be repaired at about 400 yuan.

Hello, I have seen your inquiry, please wait for a moment and answer it for you immediately.

The left fender of the modern map is more seriously dented, how much does it cost to repair?

Hello, I am your car master exclusive elite technician, I wish you a happy life and a prosperous Year of the Tiger. We promise to be attentive, careful and attentive to answer your car problems, and find solutions and solutions to the corresponding problems for you! Hello, the left front fender depression repair of this modern famous map, if the depression is more serious, the maintenance cost is between 450 550, if it is a slight depression, the maintenance cost can be repaired at about 400 yuan.

If the body is depressed and painted, it is recommended to paint sheet metal, about 300 to 500, but if there is no paint off and you are very concerned about the original paint, you can try the paint-free car dent repair technology, no need to destroy the original car paint for body concave repair, the principle is actually very simple, it is based on optics and mechanics, and the use of the lever principle to slowly restore the pits of different depths to the original appearance, look at the following picture You can see it at a glance.

Similar to the one in the picture, it is generally about 300 yuan.

The picture below is the repair effect of our sharkskin car dent repair direct store**, the first one**The black border area on the left is the appearance of the original painted body, and the right is the appearance of the body after repair, how can you feel the specific effect, but after all, there are so many stores in the country that the car dent repair can not be generalized, so I recommend that you still go to the regular brand store to repair, so that the technical level will be *** and**fixed, unlike small shops, which will only shout prices all over the sky.

You can try the paint-free car dent repair technology, no need to destroy the original car paint for body concave repair, the principle is actually very simple, that is, based on optics, mechanics, the use of lever principle to slowly restore the pits of different depths to the original appearance.

If the sheet metal is not good, the putty will have to be scraped thicker, so that the thick ash will fall off after the paint is baked, so it must be sheet gold. It's best not to touch up the paint, the whole fender should be sprayed, the fender is on the front of the car, if you touch up the paint (no matter what the technique, how good the paint color jumps) will be easy to see!

Remove it and soak it in water, and it will return to its original state, which is what the garage does.

If the area is large and deep, it is recommended that you go to a 4S shop or repair shop to do sheet metal repair. If you do not have professional sheet metal tools and appropriate techniques and strength, you may not meet your expected appearance requirements after repair, which will have a certain impact on the regular repair in the later stage.

It is recommended to carry out repairs, and now there are traceless plastic surgery in many places, as long as it is not a dead fold, it can be shaped without spray painting.

The cost is about $200,300. If you spray paint, it will cost about 300 yuan, but the value of not spraying and spraying paint is different.

You can go to the repair shop to have plastic surgery and paint, is the car insured?It's okay to go with insurance.

It's simple·· Sheet metal is fine...

The repair of the rear fender dent is very simple. First, you should go to a 4S shop or a very professional sheet metal repair agency. With the help of professionals and professional tools, general dents can be repaired successfully.

After the dent is repaired, it is time to repair the body paint. Restoring the paint surface is more round and difficult than repairing the depression. If the paint color is not adjusted correctly, a color difference will appear later.

If the painting process or environment is not good, the paint surface will be flawed. If the quality of the paint used is not good, the color will be different or even fall off after a period of use.

Automobile paint is composed of four layers, from the inside to the outside, it is the electrophoresis layer, the middle coat, the color paint layer, and the varnish layer.

1.Electric Orange Hall Swimming Layer: After the body assembly is completed, the entire body is soaked in the center of the electric swimming pool to form an electrophoresis layer. The electrophoresis layer is used to prevent rust.

3.Color paint layer: This layer of paint is the various body colors that we can usually see. The paint layer plays an aesthetic role.

4.Varnish layer: This is the outermost layer of car paint. The varnish layer can improve the gloss of the body paint and protect the body paint.

Millions of car purchase subsidies.