If you want to lay ceramic tiles at home, take the method of dry paving, do you need to soak in wate

Introduction: Many people choose to use tiles when decorating their homes, because it is also very convenient to clean, but they don't know if they need water before laying tiles if they use the dry paving method. Today, I will tell you about the ceramic tiles in the home, the method of dry paving is adopted, do you need water before paving?

The tiles are relatively smooth, and it is also very convenient to drag. It is recommended that if you don't want to sweep the floor if you have tiles in your home, you can buy a sweeping robot for mopping the floor, so that the sweeping robot can replace you with housework. It is recommended that there be such a sweeping robot,In fact, it is very convenient to clean。

What I want to tell the mourning family is that we must look at the material of the tile, for some polished tiles, it is recommended that water is not needed. However, if you want to lay ceramic tiles on the surface of the home, you must use water, because in this way, the tiles can be more compliant with the ground and are not prone to cracks. If the tile is not on the ground with the ground, then there will be a lot of problems in the future life, and it will be too late to regret it at this time.

I want to tell you that if you want to paste tiles at home, it is recommended to use some better cement, so that it is not only very convenient to paste, but also the tiles are not easy to get up. I want to tell you that if you find that the tiles have cracks or some gaps in the surface of the house, it proves that you did not pay attention when pasting. What we tell you is that you must be careful with the supervisor when applying tiles, so as to ensure that there will be no problems in life.

It must be soaked in water before paving, and only then may the tiles be smoother.

When laying tiles in the home, it is best to put water on the wall first, which can enhance the adhesion of the tiles. In this way, the tiles are more firm and flat. It is also not easy to damage when in use.

If necessary, you can better protect the tiles by doing so, and you can do better when laying them.

Yes, this is to better protect those tiles, it is more convenient when laying, and it is very good.

Need. There are many things that can be avoided and there are no water leaks in the home. So it has to be done in this way.

There is this method, but it is still necessary to use cement.

Dry tiling is generally used for the paving of ground tiles: after watering and wetting the base layer, remove floating sand and sundries. Wipe the bonding layer, use a one-to-three dry cement mortar, pave it according to the horizontal line, put the tiles on the mortar and use a rubber hammer to vibrate, remove the ground tiles and pour the cement slurry, and then put the ground tiles on the ground to vibrate and flat.

The dry paving method effectively avoids the occurrence of bubbles, hollow drums and other phenomena caused by the ground tile in the paving process, but because the dry paving method of the ground tile is more labor-intensive, and the technical content is higher, the cost of the general dry paving method is higher than that of the wet paving method, and the thickness of the dry paving will be relatively large, so it is generally used for the laying of ceramic tiles of relatively large size.

How to lay tiles (dry paving).

1. Spread the mixed mortar on the ground. It should be noted here that the ground must be clean, and if it is not clean, the cement mortar cannot be tightly bonded to the ground.

2. Before paving, the baseline of the height of the floor tiles should be set in order to maintain the overall smoothness of the floor tiles. Some well-known brand manufacturers are designed with arrows on the back of floor tiles, and the same direction of the arrows is followed when paving, so that the neatness of the dark pattern on the ground will not be produced. Place the floor tiles on top of the mortar and knock it with a rubber hammer to make the floor tiles and the mortar tightly combined.

The problem of this strength is that the master can know, if the technology is not good, it is easy to cause the floor tiles to be hollow.

3. Plaster the cement slurry on the back of the floor tile, the thickness is about one centimeter, and the floor tile is bonded by this layer of cement slurry and the dry mortar below.

4. In addition to using a horizontal ruler when paving, you must also use a long ruler, so as to keep the entire ground flat. In the place against the aluminum alloy door, leave a slight gap. Pay attention to the small picture in the lower right corner, the corners of the floor tiles, the flatness is good, and the four corners are on one plane.

Another problem is that the four corners are flat, but the middle is uneven, which means that the floor tiles are distorted. So pay attention to this when buying.

5. In addition to using a level, you must also use a long ruler when paving, so as to keep the whole ground flat. In the place against the aluminum alloy door, leave a slight gap. Pay attention to the small picture in the lower right corner, the corners of the floor tiles, the flatness is good, and the four corners are on one plane.

Another problem is that the four corners are flat, but the middle is uneven, which means that the floor tiles are distorted. So pay attention to this when buying.

6. You can see that the pedal is erected in the walking area for walking. Once the floor tiles have been laid, they should not be stepped on immediately. If the cement mortar is not dry and is trampled on, this is the main cause of hollowing of the floor tiles, which should be taken extremely seriously.

Dry paving is to mix the mortar of the floor tiles relatively dry, pinch the ball by hand, and bloom on the ground. The mortar that is wet is more watery. Generally, the wall tiles are wet pasted, and the floor tiles are dry.

However, the kitchen and bathroom floors should be wet to avoid water seepage. Dry laying can reduce the hollowing rate more than wet laying, but dry laying is more expensive than wet laying (in fact, it mainly involves a sand-to-stone ratio).

Generally speaking, dry paving has high technical requirements, mortar thickness, so that the cost is high, of course, the floor tiles after dry paving are regular, not deformed, not easy to hollow drum and line edges are flat, the effect is good, so the floor tiles should be dry paved.

Floor tile dry paving construction technology (taking 800*800 vitrified bricks as an example).

1- First clean the ground with a broom and moisten it with water;

2- Measure the horizontal line (about 1000mm from the ground) with a water level pipe, and then use the ink fountain to play the line;

3- Determine the thickness of the brick (starting from the highest point of the ground), such as: the difference level is more, and the mortar can be leveled;

4- Place the sand. Cement is adjusted into dry mortar (1:5 a little water), and cement is used to make wet slurry with a separate regulator;

5- The quality of the brick selection depends largely on the quality of the brick, and the selection of the brick is an indispensable step (the brick is taken out after comparison, and the color difference is large, the flatness and the lack of corners and edges are taken out).

6- After preparing the construction tools, first spread the dry mortar on the ground, scrape it flat (the height is appropriate to remove the thickness of the bricks under the horizontal line), and then put the bricks on it, and beat it flat;

7- Take down the brick separately and smear the cement grout on its back, and place it on the towel (note: dark lines) and beat it flat;

8- Wipe the paved bricks clean and pour an appropriate amount of water on them (to ensure that the wet cement and dry mortar are fully integrated).

9- After the brick is stable, use caulk to scrape and level the gap.

10-2 days later, you can do other work on it!

There are two ways of laying vitrified bricks in the paving, divided into "dry paving" and "wet paving", the method of wet paving is more in the nineties of the last century, but because of the moisture of the wet paving mortar, the water evaporates during the solidification process, forming small bubbles, creating a gap between the floor tiles and the mortar, resulting in a hollow drum after the floor tile paving. With the improvement of the requirements for the quality of floor tile laying, dry paving has gradually replaced wet paving and has become the main method of floor tile paving.

Dry paving has high technical requirements, because the mortar layer is thicker, and the cost is of course a little higher. Generally, the thickness of dry floor tiles is about 5 cm, including the thickness of vitrified tiles (about 1 cm).

Cement and sand are mixed with water, and the main points are:

1. Don't have too much water! If there is too much water, the cement mortar will detach from the floor tiles during the drying process, forming a hollow drum. (The difference between dry and wet is here, more water is wet.) ）

2. The ratio of cement and sand, if there is more sand, it is usually said that the cement mortar is very "fake", and the bond strength will be very poor.

Hope it helps your family!

It is to use a little damp fine sand, in the northeast of this lot, is to clean the bottom plate first, and then spread fine sand on the floor, tile paving, when all are pounced, and then a layer of fine puff is used to fill the gap, and then sweep it, you can.

cement and sand 3; 1 ratio, which is called dry paving is not prone to hollowing.

This depends on the material of your tile, which is generally determined by the water absorption of the tile. For example, the ceramic tiles that need to be soaked in water have ceramic tiles, and the water absorption rate is less than 20%, because there are some gaps in the tile material, and the ability to absorb water when paving is better, so the state of absorbing enough water is the best, I hope it can help you!

This depends on what material you use to attach the tiles. If you use ordinary cement oil for construction, you need to soak in water. However, at present, the construction materials have improved, and the use of special adhesives for ceramic tiles does not need to soak in water.

Due to the different scenes of permeable brick laying, it is usually laid on the ground, and some are laid on the construction project. At the time of construction, dry paving is usually more common, so what exactly is dry paving?

Dry paving is relative to wet paving, which means that the volume of cement and sand should be blended into dry and hard cement mortar in the ratio of 1:3-1:2, and it is used as a binding layer to lay permeable bricks and stones.

Construction process: First of all, the acceptance of the work is made with 1:3 cement mortar, the thickness of the primer is 5-7mm, and then the bottom ash reaches six or seven into dry, according to the requirements of the drawings, the elastic line and bricks are arranged. When there is flooding on the ground, pay attention to the arrangement of flooding.

To put it simply, this is the base treatment, the approximate steps: plastering the bottom ash, elastic line brick arrangement, brick invasion, inlay, and wiping the joints.

Puyang permeable brick tells you that you must pay attention to: when the dry paving permeable brick, the ratio of cement and sand is adjusted to adjust the mortar, according to the drawings to pave, before paving, do a good job of the treatment of the base, paste in accordance with the order, after pasting, pay attention to the seams.

The kitchen and bathroom wall floor is paved with glazed bricks, and the soaking time of the bricks is enough for 30 minutes, because the glazed tiles have a high water absorption rate, and the surface is dried after soaking for 30 minutes (generally 20 minutes), so it is necessary to soak in water because it prevents the tiles from absorbing the water in the cement slurry and causes the tiles to be hollow.

The whole brick (all tile) should not be soaked in water, because it is all porcelain and does not draft.

Before the tile stickers are sure to soak in water. Because there are many fine voids inside the tile, these voids have a certain water absorption. If you don't soak in water or soak in insufficient water, you will pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm, and it will cause the problem of hollowing or tile falling off.