Do you need to soak in water for the middle plate paving of horn tip tiles? How long to soak in wate

Updated on healthy 2024-07-14
23 answers
  1. Anonymous users2024-02-12

    If you want to lay the bricks, it will take two or three hours to soak them, so that the effect will be better, and the paving will be more hygroscopic.

  2. Anonymous users2024-02-11

    There are many details in the decoration that we do not know, among which there is a small detail but a very important link in the tile - tile soaking, this small detail is estimated that most owners will not know, today we will talk about why the tile paste before soaking in water! From buying a house to moving in, Issue 70 "1, why soak in water" because tiles will have a certain degree of water absorption, and if you don't soak in water, you will absorb the water in the cement sand. "2. How long to soak" is generally about 30 minutes, and the specific time is subject to the naked eye observation of the tile is not bubbling.

    3. How to soak in water "Put the tiles into a basin or bucket filled with water, and the operation is very simple; You can let the master paste the bricks while soaking in water to improve the construction efficiency alternately. "4. Do all tiles have to be soaked in water?" Vitrified tiles, polished tiles, etc. have a very low water absorption rate (less than can not be soaked, but soaking water does not seem to have much trouble, it is recommended to soak as much as possible, it is inevitable that there will be a quality of one or two bricks is not up to par (gas is a cheap tile) The water absorption rate is higher, and there will be trouble in the future.

    5. How to judge the water absorption rate "A more intuitive way is to drip water on the back of the tile to see if the water will be absorbed. "6. What will happen if you don't soak in water" If the tile with a high water absorption rate is not soaked in water, there will be problems such as hollowing and falling off after pasting. "7. Precautions" When soaking in water, handle it gently to avoid bump damage.

    The dividing line--- the dividing line--- the dividing line--- pay attention to the WeChat of the design hall, 10 minutes a day, from buying a house to moving in".If you like our article, scan **** WeChat, more dry goods are waiting for you!

  3. Anonymous users2024-02-10

    The soaking time of the brick is 30 minutes is enough, because the glazed brick has a high water absorption, and the surface is dried after soaking for 30 minutes (generally 20 minutes).

  4. Anonymous users2024-02-09

    The soaking time of the brick is 30 minutes, because the glazed tile has a high water absorption rate, and the surface is dried after soaking for 30 minutes (generally 20 minutes), so it is necessary to soak in water because to prevent the tile from being absorbed.

  5. Anonymous users2024-02-08

    [Kitchen and bathroom wall floor paving bricks for glazed tiles] The soaking time of the brick is 30 minutes is enough, because the glazed tile has a high water absorption rate, and the surface is dried after soaking for 30 minutes (generally 20 minutes), so it is necessary to soak in water because it prevents the tile from absorbing the water in the cement slurry and causing the tile to be hollow.

    The whole brick (all tile) should not be soaked in water, because it is all porcelain and does not draft.

  6. Anonymous users2024-02-07

    Look at the bricks and the bricks. All-porcelain bricks don't need to be soaked in water! The general brick 300*450 should be soaked for about 3 hours, and the 330*250 soaked for an hour can be done! That's not a comprehensive question.

  7. Anonymous users2024-02-06

    Now only the semi-porcelain wall tiles pasted on the wall need to be soaked in water, and the all-ceramic vitrified tiles do not need to be soaked in water, and you can't soak them. The wall porcelain soaking time is about 20 minutes, just don't bubble, and it's not easy to construct if you soak it for too long. This is what I learned from the people.

  8. Anonymous users2024-02-05

    It doesn't have to be soaked in water, and if you soak in water, you can generally see that it doesn't bubble much.

  9. Anonymous users2024-02-04

    The soaking of tiles needs to be divided into the water absorption rate of bricks.

    Water absorption rate "There is no need to soak in water when paving, and the glazed wall tiles and floor tiles used in the kitchen and bathroom, the water absorption rate is generally greater than 10%, and it is necessary to soak in water when paving (if it is said to be porcelain wall tiles, the water absorption rate is lower, of course, there is no need to soak in water). As the consumer asked in the morning, there can be the following answer: the water absorption rate of Yinuo polished tile is below, which can be ignored as no water absorption, and the anti-fouling wax on the surface will be washed off if it is soaked, and the brick surface will be polluted or scratched if the protection is not good during construction.

    How to soak the tiles in water: find a large basin and let the bricks be completely immersed. However, you must pay attention to handling with care to prevent the tile from falling off.

    Tile soaking is to prevent the absorption of water cement mortar moisture, so as not to cause hollowing, falling off, and even cracks, especially for wall paving, before the wall paving, it is necessary to sprinkle water on the wall, which is also the reason. Ceramic tiles will have more or less certain pores, soaking in water before paving, in order to make its pores fully absorb water, and porcelain tiles due to the density is larger, the porosity is much smaller, which makes the water absorption rate very low.

    Since different tiles have different water absorption, there is no specific standard. But the end result is that the tiles will "drink to their heart's content" until they no longer bubble. If the water absorption rate is high, it will be soaked for a longer time.

    During the rainy season, the air is humid and the time is shortened. When the weather is dry in the hot summer, the time increases accordingly.

  10. Anonymous users2024-02-03

    Before the tile stickers are sure to soak in water. Because there are many fine voids inside the tile, these voids have a certain water absorption. If you don't soak in water or soak in insufficient water, you will pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm, and it will cause the problem of hollowing or tile falling off.

  11. Anonymous users2024-02-02

    The time for ceramic tiles to soak in water is affected by two factors: the water absorption rate of the tile itself and the air humidity.

    Pre-construction preparation - material handling should be done properly, the so-called "three armies have not moved, grain and grass first", to complete the work excellently, we must make preparations in advance. Pre-construction preparation needs to pay attention to the preparation of materials and the preparation of tools.

    A large pot of tiles on the balcony, when the tiles are paved, the fit between the tiles and the wall is greater than the gravity generated by itself. Because the tile itself has many small holes and strong water absorption, the dry tile will absorb the moisture of the cement, reducing its fit, and it is easy to hollow and fall off after paving. Therefore, the tiles must be soaked for 24 hours until there are no blisters, and then they must be dried before being paved.

    Classified by ingredients and manufacturing process:

    It can be made into flat, linen, rough, polished, polished, textured, embossed and embossed surface, non-slip surface, as well as screen printing, set flowers, seepage flowers and other varieties; Among them, the technology of polished tiles is becoming more and more mature, and the market is respected and popularized.

    2. Classification according to surface decoration: wall and floor tiles are divided into unglazed and glazed according to different surface decoration methods. The surface is not glazed, which is called monochrome brick; The surface glaze is called colored glazed bricks.

    The glazed bricks can be subdivided according to the different types and colors of glazed decorations. For example, three-dimensional color glazed bricks (forked line bricks), imitation granite tiles, spotted glazed bricks, crystalline glazed bricks, bright color glazed bricks, imitation stone glazed bricks, pattern bricks, glazed tiles, etc.

    The above content reference: Encyclopedia - wall and floor tiles.

  12. Anonymous users2024-02-01

    Soak for half an hour to 2 hours, visible to the naked eye without bubbling.

    1.Tiles are fired at high temperatures, and when the cement is laid, it will absorb water and cause expansion, and if it does not absorb water first, it may lead to uneven paving or even squeezing each other and cracking.

    2.There is also the need to wash off the dust on the surface.

  13. Anonymous users2024-01-31

    Don't wait long until it's full of water and it won't bubble.

  14. Anonymous users2024-01-30

    Soak in water for a few hours. The key depends on what type of tile.

    Precautions for tiling:

    1. If you need to level the composite floor, you should do it as early as possible, otherwise it will delay the check-in time.

    2. Make the wall as rough as possible before tiling, so as to increase the contact force area between the cement and the wall. The specific method is to use an electric drill to drill more pits on the wall, the more the better. Now some decoration companies call this brushing.

    3, kitchen and bathroom wall and floor tiles laying is more important, slow work out of fine work, good workers, in addition to the ink line, find the level, but also carefully select bricks, due to the best reasons, the advantages and disadvantages of bricks are quite obvious (in the eyes of the master), and the same bricks will have a difference in size, paved out of the obvious which is big and which is small, once there are different specifications, to immediately change (paved within a day can be replaced), it is best to warn workers in advance, before the shop to choose bricks, the size of the difference as far as possible to the corner or top. (The same applies to other rooms with floor tiles).

    4. Before paving, the line should be played, and the reference line at right angles to the door entrance should be popped up on the ground, and the line should start from the door to ensure that the entrance is the whole brick, and the non-whole brick is placed under the corner or furniture, and the elastic line should be popped out of the vertical and horizontal positioning control line.

    5. When laying bricks, the bricklayer must be required to pull the line, and supplemented by a level, no matter how good the bricklayer boasts of his craftsmanship and how good he feels, it is recommended that he still insist on using tools to control the quality.

  15. Anonymous users2024-01-29

    How long does it take for tiles to be soaked? The correct way to soak tiles in water, how long should tiles be soaked in water?

  16. Anonymous users2024-01-28

    According to the survey of professionals and tilers, the tiles are soaked: the minimum time to soak in water is half an hour, followed by one hour, and two hours, and four hours (half a day) if it is long.

    Master Hu, a bricklayer with more than 10 years of experience, revealed to the author that this question is the same as how long it takes to stew chicken soup. However, as long as the principles are mastered, the clouds can be cleared: until the water is full, as long as the tiles do not bubble in the water.

    The water absorption rate of glazed bricks produced in Guangdong is generally lower than that of other real estate, so the soaking time does not need to be too long, and two hours is almost enough.

    Due to the quality of the soil in the place where Jiajiang bricks are produced, the water absorption rate of the fired products is generally high, and the soaking time is slightly extended, but 3-4 hours is enough. As for the porcelain wall and floor tiles, there is no need to soak in water.

    Chengdu's rainy days and winter are shortened due to their humid air; When the weather is dry in the hot summer, the time should be increased accordingly, and the tiles should be paved.

  17. Anonymous users2024-01-27

    The tile stickers were preceded by bai

    Be sure to soak in the water. Because there are many subtle voids inside the tile, these voids have a certain degree of water absorption. If you don't soak in water or soak in water is not enough, you can pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm, and it will cause the problem of hollowing or tile falling off.

  18. Anonymous users2024-01-26

    The soaking time is based on the time when the tiles are completely soaked in water without bubbles, generally speaking, it is only twenty or thirty minutes. The floor tiles are also to be soaked.

  19. Anonymous users2024-01-25

    Generally, tile stickers must be soaked in water before they are used.

    But there are also some that do not need to be soaked in water. Some tiles have a very low water absorption, so there is no need to soak in water. The water absorption rate of porcelain tiles, polished tiles and vitrified tiles all belong to porcelain tiles, and the embryo body of antique bricks also belongs to porcelain tiles, and such tiles do not need to be soaked in water.

  20. Anonymous users2024-01-24

    Haha, the wall tiles should be soaked, the floor tiles can not be soaked, I am about to paste the tiles, the wall tiles are soaked, whether the soaking is not soaked and the brick seller and the tiling master will tell you.

  21. Anonymous users2024-01-23

    The water absorption rate of ceramic tiles needs to be divided into bricks, and the water absorption rate is not required to soak in water when paving, and the glazed wall tiles and floor tiles used in the kitchen and bathroom, the water absorption rate is generally greater than 10%, and it is necessary to soak in water when paving (if it is said to be porcelain wall tiles, the water absorption rate is lower, of course, there is no need to soak in water).

  22. Anonymous users2024-01-22

    Wild grass and flowers by the Vermilion Bird Bridge, and the sunset at the mouth of Wuyi Alley.

  23. Anonymous users2024-01-21

    I thought I was going to soak it, but if it's 800*800, I can't find anything to put it.

Related questions
11 answers2024-07-14

First of all, it proves that you still have a lot of ideas for yourself. But you may not be thinking so much that you are on the wrong path and cannot extricate yourself. It's good to have your own thoughts, but it is recommended that if you have a situation in the future, let yourself calm down first, don't think about it, do something else, wait for a while, and then rethink this matter, maybe there will be a more mature understanding. >>>More

7 answers2024-07-14

1) Trying to be friends with him.

Talk to him about life, life, friends, family, relationships, etc., to see how he reacts and what interests him. Once you find a topic that interests him, he will be more willing to talk about it. His attitude towards you and the way he speaks to you will also change. >>>More

14 answers2024-07-14

It is very painful to learn to be on the tip of the bull's horns, but it also makes me feel very satisfied, because only when I drill the horns of the horns can I really understand these problems.

17 answers2024-07-14

Then communicate more with your parents. You have to say what you think about something, and you have to make a lot of sense about it. Even if your parents dig into the horns, you will analyze every word he says and find a point of refutation. >>>More

25 answers2024-07-14

Everyone will encounter endless difficulties and ups and downs in their lives, for some problems, we can solve it with personal ability, but many problems may also be, the vast majority of problems are beyond our personal ability, which will cause us a huge psychological burden, if your mentality is not adjusted well, you will feel pain and sorrow, your whole person may also be defeated by difficulties, and even from then on, then in the face of difficulties and ups and downs, what should we do? The key is to look at the personal mentality, when you maintain a mentality full of positive energy, in the Internet language, the gods and horses are floating clouds, so tell yourself, facing the sea, spring blossoms, from tomorrow to be a person full of positive energy Everyone will encounter endless difficulties and ups and downs in their lives, for some problems, we can solve it with personal ability, but many problems may also be, most of the problems are beyond our personal ability, This will cause us a huge psychological burden, if your mentality is not adjusted well, you will feel pain and sorrow, your whole person may also be defeated by difficulties, and even from then on, then in the face of difficulties and ups and downs, what should we do? The key is to look at the personal mentality, when you maintain a mentality full of positive energy, in Internet language, the gods and horses are floating clouds, so tell yourself, face the sea, spring blossoms, and be a person full of positive energy from tomorrow.