Do you think you should soak in water before tiling and plaving?

As the main material of home decoration, ceramic tiles must be chosen by every decoration owner, kitchen, bathroom water consumption, paste wall tiles and floor tiles is a must, but for the process of pasting tiles, I believe that most people are not very clear, do you need to soak in water before the tile paste? The answer I gave is to decide whether to soak in water or not according to the material of the tile.

Reason analysis: After the installation is completed, the fine pores in the tile will not absorb the moisture in the cement mortar or adhesive material, so as to avoid the dehydration of the adhesive material, and it will not be able to achieve natural drying, which will cause the tile to fall off and other problems, so this can avoid a series of problems in the tile. For the home decoration process, do not soak in water before paving tiles, which depends on the factorsThe role of ceramic tile soaking, the type of tile, and the part of tile pavingThese three aspects.

Let's explain the specific content below, so that you can understand this knowledge more clearly.

Ceramic tiles from a wide range, divided into full ceramic tiles and half tiles, usually the water absorption rate of the whole tile, it can be said that basically does not absorb water, this kind of brick does not need to soak in water, several households do not absorb water, so there is no need to do useless work, but this kind of brick in the wall when it is necessary to add tile adhesive or brush adhesive to prevent falling off! This is mainly due to the fact that there are many subtle voids inside the tiles, so they have a certain amount of water absorption. If you don't soak in water or soak in water enough, you can pave it directlyThe tile will absorb the moisture of the cementThe tile and cement connection part appear void, the bond is not firm, resulting in hollowing, tile falling off and other problems.

Tile soaking is a common construction phenomenon in the decoration process, some tiles need to be soaked in water, some tiles do not need to be soaked in water, and some tiles can not be soaked in water when they are laid, which is mainly related to the tiles themselves and the construction process. Therefore, we must specifically understand the reasons for ceramic tile soaking, the material types of ceramic tiles, and the construction process. Because ceramic porcelain belongs to ceramic tiles with high water absorption, there are many small gaps on the back of the brick, which is easy to absorb water, if it is not fully soaked so that the tile absorbs enough water, this kind of tile will quickly absorb the water in the cement mortar used for paving, resulting in the lack of water and incomplete solidification of cement mortar, and eventually lead to the hollowing and falling off of the tile.

Soak in water. Because the tiles can only be used longer after soaking in water, and they are not easy to hollow, so I think they should be soaked in water.

Not all tiles have to be soaked in water. According to the water absorption, ceramic tiles can be roughly divided into porcelain tiles and ceramic tiles.

Among them, the porcelain tile has a high density, small pores, and the water absorption rate is below, and it will not absorb too much water of the cement mortar after paving, so it can not be soaked in water before paving. The water absorption rate of ceramic bricks is less than 20%, and it must be soaked in water before paving.

You need to soak in water in advance so that the tiles can be more tightly attached. Won't let the tiles warp. Anyone who understands will soak in water.

It needs to be soaked in water, because there are many fine voids inside the tile, and these voids have a certain water absorption. If you don't soak in water or soak in insufficient water, you will pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm.

Generally, the floor is not needed, and if it is a tile used in the kitchen and bathroom, it is recommended to soak in water in advance. Because there are many small gaps inside the tile, it has strong water absorption, which can make the tile stick firmly. Tiles that have not been soaked in water are prone to problems such as tile falling off.

Need to soak in water. Because it is similar to the watering principle of red bricks in the past, it is necessary to avoid too much water absorption in the cement mortar, which will cause the tiles to deform and hollow, so it needs to be soaked in water and then paved.

Yes, this can increase the viscosity of the tile and the floor, so that the tile can be better laid on the ground.

Generally speaking, the wall tiles and floor tiles of the kitchen and bathroom belong to the glazed stoneware bricks, which are absorbent and need to be soaked in water before paving, and the "wet paste" method is used to pave the living room *800 large tiles generally belong to porcelain polished tiles, and the "dry paste" method is used when paving, no need to soak in water, and can be paved directly with cement Before paving the tiles, he will be soaked in water to allow the pores in it to fully absorb water, and the service life will be greatly reduced if it is too dry. It is not easy to absorb the moisture in the cement mortar and denature the cement, so that the paving quality can reach a certain standard, and it is not easy to appear hollow, fall off and even cracks

It is necessary to soak in water in advance, because this can make the tile more solid, and the specifications will be better, and the effect of water absorption is also very good, so it will be like this.

It is necessary to soak in water in advance, if you soak in water in advance, it is not easy to fall off after the tile absorbs the water, and it is very easy to fall off if you do not soak in water.

You can soak in water before pasting tiles, so that the water absorption of tiles will be particularly strong, and it is not easy to fall off after pasting.

Introduction: I believe that people who have not been decorated, do not know that the tiles are to be soaked in water before pasting tiles, many people think that the tiles can be spliced directly with cement, in fact, it is not the case, the ceramic tile soaking is mainly to prevent the absorption of moisture in the cement mortar caused by hollow drum falling off or even cracks, especially when the wall is paved, it is necessary to sprinkle water on the wall, because the tiles will more or less have some gaps in the water before paving, This will also help to keep these crevices well hydrated. Therefore, when using general glazed tiles or porcelain tiles, you must do a good job of soaking water before paving, like porcelain tiles with high water absorption, and the time you need to soak will be longer.

How to soak tiles in water.

Like the tile with a relatively low water absorption rate does not need to be soaked in water, then the tile with a relatively high water absorption rate must be soaked in water, before soaking in water, it is necessary to immerse the tile in all the water, of course, some people will directly pour water on the tile, so that the tile can only be soaked, and can not make the tile fully soaked, and it is very likely that various problems will occur after paving, so be sure to prepare in advance.

What are the precautions for soaking in water for tiles?

When soaking in water naturally, we must pay attention to the time of soaking, the color will become darker after soaking in water, and it will be different compared with the new tile, so you can use a few pieces to soak a few pieces before soaking in water, so that you can effectively avoid waste, otherwise after soaking all at one time, if you can't use up later, it will be easy to cause waste. It is generally difficult to determine the soaking time, mainly depending on the air humidity and wet water rate, generally dozens of minutes or even several hours. The floor tiles can be soaked in water for more time, which can also avoid problems in the later stage of the tiles.

Summary. Finally, after soaking in water, it is necessary to ensure that the tile is facing up, so as to avoid damage to the surface of the tile caused by excessive extrusion. It cannot be taken out immediately after soaking in water, and if it is not clean, it can be dried before the surface moisture is spread.

In this way, there will be no warping, and there will not be a lot of gaps, because it has some water absorption, if it is directly paved, it may let the tile slowly absorb the moisture in the cement, and finally there will be a lot of gaps, and it will not be firmly cemented.

It is because the tile can enhance water absorption after soaking in water, so that the tile becomes elastic, and the viscosity will be stronger and more complete when laying, and it is not easy to peel.

Because this can ensure the adsorption of the tile, it can avoid hollowing, or falling off, and can also avoid the situation of tile cracking.

The purpose of soaking the ceramic tile is to allow the tile to absorb a certain amount of moisture, and to prevent the tile from absorbing the moisture of the cement mortar after the tile is pasted, resulting in hollowing, falling off and cracking. In addition, the wall tiles will also be sprinkled in advance before the tile, the reason is the same. Since it is said to "soak in water" in advance, then the tiles must be fully immersed in water, and the construction party will generally prepare a large basin.

However, there are also some irresponsible construction teams who stack up the tiles and pour water on them with a water hose, so that they can only soak the tiles, and cannot let the tiles.

Vitrified tiles are not used, and tile adhesive is not used. Whether to soak in water depends on the water absorption rate of the tile, the best simple way is to try to take a piece of brick before pasting, such as the bubble brick has a small bubble bubble out and the bubble brick and the bubble brick is not soaked compared with the color darkened or different, such as the cement sand in which the pores fully absorb the water, too dry if the service life will be greatly reduced, after absorbing sufficient water, smeared with cement mortar, so as not to absorb the moisture in the cement mortar is easy to denature the cement, so that the quality of the paving can reach a certain level.

Be sure to soak the tiles in water. There are two ways to lay tiles, one is dry paving, that is, cement yellow sand with a small amount of water, twisted into wet sand to pave tiles, and the second kind of wet paving, that is, cement sand twisted into a paste. Both methods need to be soaked in water.

After more than 10 years of experience, the wall tiles in the kitchen and bathroom are soaked in water, because these bricks need to absorb water so that they will not fall off due to hollowing. Some merchants sell this kind of wall tiles and say that his *** does not suck.

If it is the wall and floor tiles of the kitchen and bathroom balcony, because of the high water absorption, it must be soaked in water. Otherwise, the tile will absorb the moisture of the cement mortar, causing the tile to hollow and fall off. And polished tiles can not be soaked, because they have a very low absorption rate.

What is easy to know the water absorption of this brick? Teach you an easy way, the more intuitive way is to drip water on the back of the tile, to see if the water will be soaked by the tile, that is, to completely soak the tile in the water, it is generally recommended to use a larger capacity basin for soaking; It should be noted that do not use a water hose to simply sprinkle the tiles, because this soaking method can not make the tiles fully soaked, and it is very good after paving.

If you use the traditional method of tiling, that is, the cement mortar pasting, the tile must be soaked in water, and the role of soaking water is to let the tile absorb enough water in advance. This is because this method of tiling relies on mechanical mating. If the tile is not soaked in water in advance, the pores behind the tile will absorb a lot of water, which will cause the cement mortar to lose water and lose its effect, and eventually the tile may be hollowed out and fall off.

Therefore, if you use the traditional pasting method to paste tiles, the tiles must be soaked in water.

Yes, there will be no bulging, falling off, cracking, and it is conducive to absorbing the moisture of the mud well and deepening the firmness.

Of course, it is necessary to soak in water, because after soaking in water, it can ensure the adsorption of tiles and prevent them from falling off.

Must be soaked in water. In order to allow the tile to absorb a certain amount of moisture, prevent the tile from absorbing the moisture of the cement mortar after the tile is pasted, resulting in hollowing, falling off and cracking.

Yes, this is because the tiles soaked in water are relatively strong against the wall, and there will be no warping or falling.

Under normal circumstances, tiles do not need to be soaked in water, because the tiles need to be cemented, and if the tiles are soaked in water, it is not easy to paste.

It needs to be soaked in water, and it needs to be soaked for about an hour, which is also very beneficial to the tiles, and the tiles are also very strong.

Need. Soaking in water can avoid the tile absorbing the components in the cement mortar, resulting in hollowing and falling off, especially for the tile paving of the wall, soaking in water is an indispensable step.

Just bought tiles, more or less there will be a certain gap, the first tile soaked in water, you can let the tile fully absorb water, after absorption, the gap will reach saturation, and then when paving, it will not absorb cement mortar.

Before the tile stickers are sure to soak in water. Because there are a lot of tiles in the interior.

Microscopic voids, which have a certain amount of water absorption. If you don't soak in water or soak in insufficient water, you will pave it directly, and the tile will absorb the moisture of the cement, so that there will be a gap between the tile and the cement, and the bond will not be firm, and it will cause the problem of hollowing or tile falling off.

Tile soaking is to prevent the absorption of moisture from cement mortar, so as not to cause hollowing, falling off, and even cracks, especially for wall paving, before wall paving, it is necessary to sprinkle water on the wall, which is also the reason. Ceramic tiles will have more or less certain pores, soaking in water before paving, in order to make its pores fully absorb water, and porcelain tiles due to the density is larger, the porosity is much smaller, which makes the water absorption rate very low.

Which tiles need to be soaked in water?

The main purpose of soaking the tile is to make the tile "drink" full of water, so that it will not absorb the moisture of the cement mortar, and not all tiles need to be soaked in water. If the water absorption rate of ceramic tiles is very low, then, there is no need to soak in water, such as porcelain tiles, polished tiles and vitrified tiles that are water absorption, and some manufacturers of antique bricks also belong to porcelain tiles, such tiles, there is no need to soak in water. In addition, we don't need to soak the ground tiles in water, and the glazed wall tiles used in the kitchen and bathroom generally have a water absorption rate of more than 10%, so they need to be soaked in water before paving.

The right way to soak tiles in water?

1 Use a large plastic bucket.

2 tiles stand up for soaking.

3 Tiles must be completely submerged in water.

4 Until there are no bubbles.

The bricks are erected and completely soaked in a plastic bucket filled with water.

The porcelain tiles must be soaked for more than 2 hours until there are no bubbles. After drying, go to the wall: Dry the porcelain pieces soaked in water for 15 minutes in a dislocated way, and dry them for later use.

The incorrect soaking method is: lying flat in the barrel, not fully soaked, sewage soaking, and the wall will appear yin and yang.