What should we do if the lock of our bedroom door cover is broken?

If the lock of your bedroom door sleeve is broken, you should replace it with a new lock. The simplest and most brutal way is to change the door directly, don't just think about changing the door cover. The door cover is not expensive, but I'm afraid no one can do it alone.

Because the workload is too small and the fee is low, the store will feel that it is not cost-effective. So we can reassemble the pieces of the door frame and glue them together with all-purpose glue. For cracked cracks, we can buy wood grain stickers close to the original door cover, if you are careful, you can achieve a good effect.

1.Before installing the bedroom door, check the size of the door opening, including whether the yin angle is square, and ensure that the upper edge is on the same horizontal line, so that the installed door sleeve can reach verticality and flatness. Next, a large core board should be used as a lining plate and fixed in the door opening.

If the gap is large, you can make a bracket and then fill the gap. If the gap is not particularly large, plug the gap directly with cement mortar. Next, it needs to be installed.

You need to set up a vertical liner first. After straightening, it needs to be fixed firmly with nails.

2.Depending on the degree and area of the door frame lock slot, different methods are employed. Self-maintenance repairs and new repairs.

If the part of the door sleeve (door frame) with a keyhole is broken, you can buy a larger stopper, that is, the block of the latch, and reinforce it. If the damaged area is too large, you can consider replacing it with a large slab. If the lock position of the door frame is broken, you can remove the bad part, insert a piece of solid wood, and open a lock hole.

The wooden strip on the side of the door frame lock groove is broken. Emergency treatment in the event that the door lock cannot be opened because a foreign object is stuck in the lock. Generally, there are foreign objects stuck in the door lock, which cannot be inserted with a key or finger, and it is difficult to twist it even if it is inserted, in this case we must find a way to unscrew the door lock.

3.Once the door sleeve is installed, the bedroom door can be installed directly and then fixed to the door frame by hinges. You need to make a hole in a certain position to install the hinge, and then try to open and close the door after the hinge is in place.

It's not difficult to fix the door cover yourself. It is only necessary to repair the door cover in different ways according to the degree of damage to the door cover. This person needs to check the judgment first, otherwise it is easy to get worse and worse.

The above is the answer to the question of what to do if the lock of our bedroom door cover is broken.

You can find professional workers for maintenance, so that you can get a good solution, and you can also protect yourself, you can choose some better materials. You can also go to the place where you bought the door to make the relevant repairs.

You can find a professional maintenance person to help you replace the new bedroom door sleeve lock, and also strengthen it, so as to ensure safety and practicality.

You can directly buy a new lock key to replace, or you can find some professional lock changers to replace it, so that it can be used normally.

The door lock is broken, and you are locked in the room, and there are currently two ways to save yourself:

1. If you have strong hands-on ability, you are generally locked in the room, and the lock inside can be removed by visible screws, so it is recommended to take a screwdriver in the room.

If you don't have a screwdriver, you can also use the key of the cross, take off the two screws behind the lock, take a small stick to get the spring inside, the specific part is not certain, as long as the stick is put in, turn a few times, you can always touch, and then dial it, and the door will open naturally.

2. If you can't open the door, it is recommended to call relatives and friends for help, or call 110 directly for help.

Home lock maintenance method:

1. After most friends open the door, they will always push the door to the door frame, so that it can have the most intimate hug with the door, but this is not what the door wants, after we open the door, we should rotate the handle, so that the lock tongue of the door is retracted, and then the door frame is combined, in the release of the hand, in short, it is necessary to avoid the serious collision of the door lock, otherwise it will shorten its life.

2. When we open or close the door of the lock body, it will often rotate to it, and over time it will not be so flexible, therefore, we need to ensure that the rotating part of the lock body has lubricant, so that the friction of the lock body itself can be reduced, thereby increasing the service life of the lock itself, and in order to ensure the safety of the lock, we had better check whether the lock nail is loose.

3. In addition to the lock body we will often rotate, the lock cylinder is also a place we often come into contact with, after a long time, the key will not be smooth in the process of unplugging and inserting, therefore, we need to add some items that can lubricate it for the lock cylinder, of course, the lock cylinder is absolutely not able to add lubricants or some oils.

Therefore, it is best to choose to add some graphite powder, which is the powder of the pencil lead, which can have the best lubrication effect on the lock cylinder.

If the lock cylinder of the bedroom door is broken, you can use the help of forced unlockingWrenchandScrewdriversand other tools to force unlocking.

After the lock cylinder is broken, it is definitely impossible to open the door lock through the key, in this case, we have to pry all the discs of the door lock first. Before picking the door lock, we need to prepare a wrench and a screwdriver and other tools, and after prying the door lock disc, we need to use a flathead screwdriver to unscrew the two screws inside the door lock. Finally, pull out the damaged cylinder and door lock from the outer end of the door.

Forced unlocking is a technical job, and it is recommended that you should ask a professional to help you to ensure that the lock cylinder can be used normally. If the cylinder does not open because there is a problem with the internal deadbolt, you should find out the position of the deadbolt and reset the screws fixed to the correct position from the crack in the door.

How to choose a bedroom door lock?

1. Look at the appearance

Generally speaking, all bedroom door locks need to go through the process of plating, spraying or painting before leaving the factory. These processes are beneficial to the bedroom door lock itself, because after the treatment of these processes, a protective film will be formed on the surface of the bedroom door lock, so as to play the role of anti-corrosion and anti-oxidation. Therefore, if the appearance of the door lock does not show the traces of this treatment, then it is best not to choose.

At the same time, we should also look at the appearance of the door lock and the door when choosing.

It is in harmony with the room.

2. Look at the weight and feel

** and defective products.

There are differences in weight and feel. Let's say it's a door lock that cuts corners, then it's usually made from hollow defective materials. Such a door lock is not only lighter, but also feels worse when used.

3. Look at the brand

Whether it is at home or abroad, there are very strict specifications for hardware door locks. Although some small manufacturers will not comply with the specifications in order to save costs, large brands will abide by the specifications. Therefore, when choosing a bedroom door lock, try to choose a well-known door lock.

Dear Glad to answer for you. 1. Disassemble the lock cylinder: disassemble the lock cylinder, then disassemble the lock shell, and hit the lock cylinder with a wooden stick or hammer to return it to the correct position.

2. Adjust with a key: On the right side of the lock, there is an adjusting screw, turn the adjusting screw with a small key, so that the lock cylinder can enter the lock correctly. 3. Use pliers to force unlocking:

Turn the pliers open, use the pliers to compress the cylinder, let the cylinder move clockwise, and then open slowly. 4. Use the key to wipe the lock: Wipe the key into the lock and wipe the lock cylinder vigorously until the lock cylinder is wiped open.

5. Use a hammer to unlock the lock: Put the hammer head on the lock cylinder, hit the lock cylinder hard, and wipe the lock cylinder open. 6. Use a brush or zipper to unlock the lock

Place a brush or zipper into the lock and pull slowly so that the cylinder is removed.

If the bedroom lock is broken, it can be unlocked by picking the door and locking it in the house.

Find the wire or have a small hole in the neck of the grip, insert the flat tenon grip and pull it outward, pry the cover after the handle is taken off, and there are two fixing screws to turn it open.

When the lock body is pushed out, only the oblique tongue remains, find a needle-nose pliers or a flat-mouth driver, and drive the oblique tongue to the horizontal dial without letting go, and it will bounce back after letting go, and then push the door open.

1. Pry door methodWhen people are inside: find the wire or have a small hole in the neck of the grip, insert the flat tenon grip and pull it out at the same time, pry open the cover after grasping the handle and taking it off, there are two fixing screws to turn it away, and when the lock body is pushed out and only the oblique tongue is left, find a needle-nose pliers or a flat mouth driver, and drive the oblique tongue to the horizontal dial and do not let go, and it will bounce back after letting go, and then push the door open.

2. Smashing the doorBeing locked in or out of the door, is not a good experience, I believe there must be a small partner waiting for a hurry, take violence to open the door, the lock is destroyed, although this method is not recommended, but it is indeed a way to open the door, of course, if you are not afraid of trouble to change the door or lock or something! Therefore, everyone should take it easy!

3. Seeking helpHurry up and call the property or call the locksmith. I think that such a difficult technical job as prying the door is not something that mortals of my generation can easily control, and smashing the door or something, the lethality is too great, if it is not in a particularly embarrassing or urgent time, such as in the middle of the night or before going to work in the morning, we still ask the locksmith to come over!

If the orange section of the bedroom door lock is broken and there is no spare key, you can try the following methods to force the lock: 1. Use the card: Insert a plastic card or similar sheet between the lock cylinder and the door frame while gently shaking and twisting the card to try to pop the deadbolt open.

2 Use pliers: Insert a pair of slender pliers into the lock cylinder and try to twist and grasp the deadbolt to open the door lock. 3. Use a drill or screwdriver:

Using a tool such as a drill, hand drill, or screwdriver, start at the hole or on the side of the cylinder and gradually expand the hole diameter until the cylinder is opened. 4. Use locksmith tools: You can buy some professional locksmith tools, such as lock picks, lock cylinder hooks, etc., to try to open the door lock.

It should be noted that all of the above methods may cause damage to the door lock, and special care needs to be taken when forcing the lock to ensure the safety of yourself and the door lock. If none of the above methods are feasible, we recommend that you seek the services of a professional locksmith to ensure that the door lock is fully opened.