Can glue be used to apply tiles? What to pay attention to?

The mortar can also be applied to the tile, but it must be noted that the tile and the mortar are tightly adhered to, and at the same time, after the tile is glued, it must be pressed for a period of time, so that the tile can be installed very tightly.

It can be pasted. First of all, we should pay attention to the mixing ratio and consistency of the glue, and secondly, the base surface of the wall should be kept flat and clean, otherwise there will be a danger of falling off.

1. Use an electric mixer for the best mixing effect;

2. The proportion of gouache can be appropriately adjusted due to different substrates, weather, construction conditions, etc.;

3. During construction in rainy days, it is necessary to take sheltering and protective measures, and ensure that the construction area is not wet by rain within 24 hours after tiling;

4. The glue should be used within 2-3 hours according to the weather conditions;

5. Do not mix the dried glue with water before use;

6. The scraping of ceramic tile adhesive should be uniform and full, and the thickness of the adhesive layer should be about half of the tooth pitch of the tooth scraper used.

7. After the brick laying is completed, the next step of the caulking process can only be carried out after the glue is completely dried (about 24 hours).

Of course, we must pay attention to the consistency of the rubber paddle is not very strong, and we must pay attention to the indoor temperature when pasting, so that we can decorate the home very well.

1. What glue is used for tiling?

1. Tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting decoration materials such as surface tiles, tiles, floor tiles, etc., and is widely used in decorative places with architectural finishes such as ground, interior and exterior walls, bathrooms, kitchens, etc. Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material.

Tile adhesive is suitable for pasting all kinds of floor tiles or small bricks on the wall surface of ordinary mortar surface.

Tile adhesive has strong adhesion and anti-falling performance, and is suitable for the pasting of wall tiles, non-mortar surfaces such as wood plank surfaces or old finishes with large adhesion requirements.

Tile adhesive has large adhesion, more flexibility, can resist the stress caused by thermal expansion and contraction of the adhesive layer, and is suitable for pasting ceramic tiles on gypsum board, fiberboard, plywood or old finishes (tiles, mosaics, terrazzo), etc., as well as pasting various stone slabs of larger sizes. In addition to gray, tile adhesives are also available with a white appearance, suitable for light or translucent marble, ceramic tiles and other natural stones.

Second, tile adhesive construction method.

1. Clean the construction surface first, and keep the surface to be firm, dry, clean, and stain-free;

2. Stir the tile glue into a paste in the water, the proportion is 25 kg and add about 6 kg of water, after stirring sufficiently, wait for about ten minutes and then stir it slightly to use, and use it in about 2 hours, do not reuse the dried glue glue.

3. The toothed scraper will apply the mortar on the wall, evenly distribute about one square meter, and knead the tile on it in fifteen minutes. If it needs to be adjusted, it needs to be before the tile adhesive is not fixed.

4. Pay attention to retaining the expansion joint, the product is suitable for use in the environment of 5 40, and can only be stepped into or filled after 24 hours after completion. If it has been cured for more than 24 hours, the stains on the surface of the tile can be cleaned with a tile and stone cleaner (do not use acidic cleaners).

5. Before use, the verticality and flatness of the substrate must be confirmed. Do not mix the dried glue with water for reuse. Take care to keep the expansion joints.

When we decorate, we generally use glue when laying wall tiles, on the one hand, we can use wall tiles to stick to the wall more firmly, and if there are some gaps, glue can effectively maintain the aesthetics. Therefore, it is also very necessary to choose glue, although it is a relatively small thing, but its role is very large, so what glue is generally chosen, let's introduce to you what glue is used for wall tiles? How to use wall adhesive?

Let's take a look.

Tile adhesive introduction

Tile adhesive, also known as tile adhesive or binder, adhesive and other names, is a new type of material for modern decoration, replacing the traditional cement yellow sand, the adhesive force is several times that of cement mortar, can effectively paste large ceramic tiles and stones, and avoid the risk of falling bricks. Good flexibility to prevent hollowing in the production of drums. It is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, floors, bathrooms, kitchens and other building finishing decoration places.

Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material.

Tile adhesive classification

Tile adhesives are generally divided into ordinary type (model 1), strong type (model 2) and tough type (model 3). Among them, ordinary tile adhesive is generally used for the bonding of a variety of floor tiles or small wall tiles on the ordinary mortar surface; Strong tile adhesive has stronger adhesion than ordinary glue, and has the ability to prevent falling, and is suitable for wall tiles and wood boards with relatively large adhesive requirements; Strong tile adhesive has excellent flexibility, very large adhesion, better than strong type, can effectively prevent the damage of thermal expansion and cold contraction to ceramic tiles, usually used for fiberboard, gypsum board, plywood or old finishes and other bonding.

How to use tile adhesive

The first step: wet the construction wall and ground, the inside of the wall and ground must be kept dry, the surface of the wall and ground needs to be kept flat, and the uneven or rough surface can be smoothed with cement mortar;

Step 2: Remove the base layer of floating ash, oil and other stains, otherwise it will affect the adhesion of tile adhesive;

Step 3: Adjust the binder, the water-cement ratio is about 1:4, and stir well. The binder should be used up within 5 to 6 hours (when the temperature is relatively high and the light is sufficient, it should be used up in a shorter time);

Step 4: Apply the mixed adhesive to the back of the tile to be laid, press firmly until the tile surface is flat, and the tiles laid in 15 minutes can be corrected by moving.

What we have introduced to you above is about what glue is used for wall tiles? How to use the wall adhesive related issues, we should have some understanding of these problems. In fact, we know that although this glue looks relatively small, but its role is very large, so we should also pay attention when choosing, if the choice is not suitable, not only will it affect the appearance, but also make the wall tiles not firm, so if we want to choose, we also need to know more about the relevant knowledge.

With the improvement of the decoration quality of modern people, more and more vitrified bricks and stones are pasted on the wall, but it is difficult to paste the wall firmly with traditional cement mortar, and there are often hollow drums and bricks. In order to achieve better construction results, the use of back coating glue and tile adhesive is becoming more and more frequent.

The function of tile adhesive is to strengthen the occlusion between the tile and the wall, the tile adhesive has strong adhesion, is not easy to fall off, and can effectively prevent the occurrence of empty bricks, falling off and other phenomena.

If it was placed ten years ago, there was not much difference between the tile paving and the use of tile adhesive, but at present, the popular semi-vitrified bricks in the home improvement market or even the full vitrified bricks, the surface of the tiles is dense, the water absorption rate is very low, and the pasting principle of the traditional cement mortar mechanical occlusion has lost its effect.

In contrast, the intermolecular forces generated by polymer additives in tile adhesives can enhance the bond strength, easily reaching 2 to 4 times that of cement paving.

The use of ceramic tiles on the wall will greatly improve the quality and reduce the hollowing and falling off phenomenon after the tile is paved! Porcelain tiles belong to clay tiles, it stands to reason that as long as they are soaked in water before paving, if the construction is done properly, even if it is paved with pure cement, there will be no difference between tiles and porcelain, although porcelain tiles and tiles are only one word, material, specifications, textures are not the same, and the paste position is not the same. The surface of the tile and the bottom of the embryo are pure full-body bricks of the same material, and the tile material and density are very high.

The tiles used in the decoration of our homes, if they are divided according to the parts used, I personally think that they are actually two categories. The first category is the common tiles on the ground, which we commonly call floor tiles. The second category is that the cost of sticking on the wall is relatively low, but if the ceramic porcelain is pasted in a porcelain way, it not only costs more, but also gets the opposite effect, resulting in faster bursting of the porcelain piece!

The porcelain tiles of the porcelain body are different, and they must be paved with tile glue, and it is best to add a brick back.

The use of tile adhesive can only be used when the surface is very flat, and if it is not flat, it also needs to be leveled manually with cement mortar and other materials. This not only adds more manpower and material resources to the construction, but also if the base layer after leveling has floating ash and the like, however, this paving method can often only be used for ground tile paving or wall porcelain paving, the reason is very simple, the tile (floor tile) size is large, the weight is heavy, the water absorption rate is low, and the cement mortar is paved on the wall, and the consequence is that the tile and the cement mortar are not bonded.

When the wall cement mortar is leveled, you can use tile glue to paste porcelain, and the tile adhesive adhesive can not be greater than the centimeter, otherwise the adhesive surface gap is too large and easy to fall off. Copper wire to pave, ordinary cement to paste will have a lot of problems in the later stage. Although ceramic tiles and porcelain tiles have a porcelain character, there is a big gap in thickness, and the thickness of porcelain tiles is relatively thin and lightweight.

But the tiles are thicker and heavier.

It is necessary to use tile adhesive, because the tiles on the wall are easy to fall off, so it is necessary to use such an adhesive to assist.

It is because tile adhesive is needed when you want to paste tiles, and ceramic tiles are not the same as porcelain tiles, porcelain tiles are usually thinner and lighter, so they are not suitable for tile adhesive.

You can use tile adhesive or cement mortar, which will be a little more expensive with tile adhesive, and you can save decoration costs with cement mortar.

Of course, it is needed, because when the wall is covered with these porcelain tiles, there is a high chance of falling off, so you need to use tile adhesive to ensure the quality.

Summary. OK! Must be used.

It is necessary to use tile adhesive, and can you use tile adhesive on the wall tiles?

OK! Tile adhesive must be used, tile adhesive must be used, because tile adhesive is stronger than cement mortar, and the construction is simple, and it can be laid directly on the dry wall. However, it is necessary to soak the tiles in advance, and stir the tile glue in proportion and leave it for 10 minutes, and then use a gear scraper to evenly wipe the wall, and then knead and press the tiles that have been placed.

What are the precautions for the use of tile adhesive 1, the base should be kept clean, the floor surface is the surface of the wall or floor in direct contact with the tile adhesive, and the dirt and oil stains should be cleaned so as not to affect the bonding effect of the tile. 2. Uniform scraping, if the thickness of the tile adhesive is uneven, the edge position may be bent, and the tile may be hollow. 3. Tile adhesive can not be immersed in water, tiles paved with tile adhesive do not have to be immersed in water, for some tiles with low water absorption, it is not easy to absorb water when soaked in water, so you can directly use tile adhesive to wrap tiles.

However, vitrified tiles, tiles, etc. should not be immersed in water, otherwise the adhesive strength of the tile adhesive will be reduced, causing the tiles to fall. 4. The tile adhesive that has been prepared must be used up in time. The tile adhesive that has been mixed evenly should generally be used within 2 hours, otherwise it is easy to cure and dry, and the cured and dry tile adhesive cannot be used to paste tiles.

OK. Mortar and water in accordance with: water = 100:

20--25 ratio stir evenly, into a paste, electric stirring effect is better, let stand for 5-10 minutes and then stir to increase the strength. The base treatment is clean and coarse, and the smooth surface of the toothed spatula is scraped on the surface of the base layer, and the construction thickness is 2 3mm, and then the tooth surface of the tooth spatula should be scraped out of the concave and convex grooves, and then the tile is pasted, and leveled and compacted, and the tile can be adjusted within 10 minutes. The prepared glue should be used up within 2 hours.

The use of ceramic tile tiles on ceramics can greatly improve the quality and reduce the hollowing and falling off phenomenon that occurs after the tiles are laid! Ceramics belong to clay tiles, it stands to reason that they are soaked in water before packaging, and if the construction is good, there will be no quality problems when paved with pure cement? Wouldn't it have a big impact if you didn't add a ceramic tile binder?

But ceramic tiles are more adhesive, so it will be better to use ceramic tiles to lay tiles! When we lay porcelain, we often add ceramic tile binder to the mud to save the cost of accessories and achieve good quality results! However, if the ceramic tile adhesive is added to the cement, it will cause a chemical reaction, and it is doubtful that it will affect the quality of the paste.

But since there are ceramic tiles, this kind of operation has been done, and there is no problem, right?

Walls on ceramic are a bit safer than walls on floor tiles, but the quality is further guaranteed by using ceramic tile stickers! I'm just a renovation worker, don't I sell ceramic tile adhesives? Don't I use advertising ceramic tile adhesive either?

From my practical experience, I can see that tiles that use ceramic tile adhesive are of better quality than those that do not! Can't you ruin more than 20 years of credibility and reputation for the sake of advertising ceramic tile adhesives? It's all a matter of experience!

Ceramics are wall tiles, new home decoration, balcony, kitchen, bathroom sticker wall tiles. The so-called ceramic. Porcelain is thin and small, 300*600 is the largest specification.

This is because the ceramic surface and the bottom of the embryo are not the same material. The ceramic surface does not absorb water. The bottom of the embryo is rough and has many small pores.

Tile 2, tile, tile has differences. There is only one word for tile and tile, but the material, specification, texture is different, and the position of the paste is also different. The surface of the tile and the bottom of the embryo are pure all-body bricks of the same material, the tile material and density are very good, and they can achieve zero absorption rate.

The tiles are made using the corresponding embryonic material. It is generally clay, but there are many types of clay. Roasting, pressing, sanding, cutting these clays and eventually making them our common tiles.

The tiles used in the decoration of my home are divided by the parts used, and I personally think that there are two main categories. The first big category is tiles that are attached to common floors, which we usually call floor tiles. The second category is tiles that are attached to the wall, which we usually call wall tiles.

The upper wall of the above-mentioned floor tiles is to paste the floor tiles on the wall surface and use them as wall tiles.