-
How to paint:
1. First, the steel plate is surface treated, dust-free, oil-free, dry, rust-free, non-scale, and the roughness adhesion is better if it is polished.
2. If the finished paint is mixed with thinner according to the instructions, the paint will be used 10-15 minutes after the paint is adjusted.
3. Primer: pre-coat the edges, corners, holes and other positions of the steel plate, because the paint has the characteristics of shrinkage when curing, and the film thickness at these positions will be thinner if you do not pre-coat, which will affect the anti-corrosion.
4. Brush a large area with a flat paint brush, and the original pre-painted parts should also be followed. When brushing, pay attention to the direction, generally brush horizontally and then vertically, and be careful not to leave brush marks.
5. The general anticorrosive primer is brushed twice, and the pre-coating should be done before the second brush. There is a time interval between the first and second brushes in the manual, and the surface is generally dry.
6. If there are defects such as brush marks or sagging after the paint surface is dry, there is a fine sanding paper to lightly sand.
7. Brush the topcoat according to the above method.
8. Pay attention to environmental conditions during the construction process.
What to do with the brush that paints the paint:
Step 1: Remove any excess thinner from the brush where the paint is applied. Squeeze the brush into the container by hand and use a clean paper towel to absorb the remaining thinner that cannot be squeezed out.
Until you know that the thinner no longer appears on the tissue. If there is still paint on the paper towel in this step, go back to the second one.
Step 2: Slowly tap the palm of your hand with a paint brush inside the large cardboard box until no paint splashes out. Wipe it with a paper towel again.
Next step: Dispose of the brush to brush the paint off the used thinner. Put the thinner in the three cans into one can, close the lid, and dispose of it properly.
-
First to batch putty, grinding, then you can brush the paint, to a small number of many brushes, the last time dry brush the next time, too thick wrinkles, need to be apprenticed first, full of teachers before they can operate alone. The workplace should be ventilated, avoid open flames, and wear gas masks.
-
In terms of tool selection, it is recommended that you choose a tool with better quality, so that the coating we brush out will be thicker and the texture will be better.
The original bottom color can be covered, which can ensure the durability of the paint film and can withstand repeated scrubbing. Painting is a more important link, and the painting process is more, the construction period is longer, if you don't brush well, the overall effect is very poor.
If you encounter some bad decoration team construction, it is easy to cut corners and other problems. Prepare in advance, first protect windows, doors and other places that will come into contact with paint, and use things to avoid paint falling off and affecting the appearance.
The color is uniform
Adjust the color of the paint well, so that the color of the paint is uniform, and avoid water stains. After the roller is painted, the corners of the wall should be repaired with a brush, especially at the joints of the chain stalls and the corners of the walls. Sand the wall, and when the paint is dry, you can use sandpaper.
This is to reduce the wall brush marks, make the wall smooth, and after sanding, the wall should be thoroughly cleaned.
After the paint is completely dry, you can carry out acceptance and check whether the wall paint color meets the requirements and whether the paint color is consistent. Whether the paint surface is uniform, whether there are quality problems such as blistering. Paint should pay attention to the base layer putty is not scraped flat, and pay attention to cutting corners when carrying out base treatment.
In order to save time and workload, some construction teams shouted that the grassroots putty was not scraped flat, and then they were in a hurry to do the follow-up construction period.
-
Share some practical tips for brushing paint, and learn that it is definitely not a loss, and it can always be used in life.
-
Wall base treatment, coating interface agent, waterproof treatment, anti-crack treatment, batch scraping putty, grinding and repairing, primer, topcoat. The most important thing for painting is to do a good job in the base treatment, including leveling, waterproofing, caulking and so on.
-
The methods and tips for brushing paint are as follows:
1.Prepare the tools: Choose the right brushes, rollers and paints, and choose different models and materials of brushes and rollers according to your needs.
2.Preparation: Before you start painting, clean the surface of the wall or furniture to remove dust and debris and make sure the surface is smooth and flat.
3.Painting sequence: Paint the corners and edges first, then the large areas, so that you can avoid missing and repeating the brush.
4.Painting skills: When applying oil concealment paint, it is necessary to keep the arms and wrists stable, and use even force to avoid brush marks and dripping. When painting, it is necessary to pay attention to the thickness and uniformity of the paint to avoid uneven thickness.
6.Cleaning tools: After the painting is completed, clean the brush and roller in time to avoid the paint drying and fixing on it, which will affect the next use.
It should be noted that it is necessary to pay attention to safety when brushing paint, avoid splashing paint on the eyes and **, and at the same time maintain good ventilation to avoid the impact of paint smell on the body.
-
The methods and tips for brushing paint are as follows:
1.Preparation: Deeply clean the area that needs to be painted and ensure that the surface is dry and free of grease, dust, etc., to ensure that the paint can adhere.
2.Choose the right brush: Choose a tanned brush head and keep the bristles neat and not falling off. The size and shape of the brush should be selected according to the area and shape of the brush, so as to better complete the painting job.
3.Stirring the paint: Stir well after opening the paint bucket to ensure that the texture of the paint is uniform, and before brushing, you can dip the brush with a small amount of paint and remove excess paint from the edges, these operations can help to avoid run-out and combing the paint to avoid irregularities.
4.Start brushing: from top to bottom, from the outside to the inside or from left to right to paint, if necessary, you can carry out a second coating, when painting oil which old leakage paint, be careful not to paint too thick or too much, so as not to cause outflow and plaque formation, after the painting is completed, pay attention to the paint brush, ensure that the paint and brush are clean and tidy before the next use.
-
Brushing paint is a job that requires skill and experience, and here are some methods and tips to help you do the job:
Preparation:1Clean the surface: Before painting it, the surface must be cleaned. Use a detergent and water mixture to wipe down the surface to ensure it is clean, dust-free, and smooth.
2.Repair surfaces: If there are cracks or dents, they need to be filled with filler first. Wait until the filling is completely dry before sanding the surface with sandpaper.
3.Protect the surrounding area: When painting, you need to protect the surrounding walls, floors, and other furniture. Use plastic sheeting or newspaper to cover areas that do not need to be painted and secure them with tape.
Choose the right tool:
1.Brushes: Choosing the right brush can make your job easier and more effective. For smaller details, a small brush is an option; For large areas of coating, a large brush should be chosen.
2.Rollers: Rollers are better suited for coating large areas than brushes. They can be applied more quickly and the thickness of the coating can be controlled more easily.
3.Spray guns: If you need to paint a large area, it's best to use a spray gun. They can be applied faster and it is easier to control the uniformity of the coating.
4.Paint buckets: Choosing the right size paint bucket will make it easier for you to mix and store paint.
Choose the right color and type:
1.Choose the right color: When choosing a color, you should consider the light and ambiance of the room.
Dark tones can make a room look smaller, while bright tones can make a room look bigger. At the same time, consider the color and style of the furniture in order to harmonize with them.
2.Choose the right type: Choose the right type of paint based on the desired application. For example, easy-to-clean latex paint can be used for interior walls, while wood paint or varnish can be used for wooden furniture.
Tips:1Be regular when painting: Do it regularly when painting and don't overdo it every time. This helps to avoid dripping and blistering.
3.Apply a few more layers: For better results, you can apply the second layer after the first layer has dried. Applying a few more layers can make the coating more robust and durable.
4.Pay attention to ventilation: Keep it well ventilated during painting to avoid inhaling harmful gases. It is best to do the painting work outdoors or in a well-ventilated area.
5.Pay attention to safety: Pay attention to safety during painting, wear appropriate protective clothing and gloves to avoid damage to ** and health. At the same time, keep unwanted paint out of the reach of children.
-
The methods and tips for brushing paint are as follows:
1.Choose the right brush. When used for indoor painting, it is generally recommended to use a natural bristle brush with moderate hardness, good volume and flexible texture.
2.Prepare the paint. After stirring well, take out the content and bring it out, and filter out the possible impurities through the strainer.
3.Treat the surface. Treating surfaces usually requires preparation in advance, such as cleaning grease on the walls, polishing uneven parts, etc.
4.Start painting. Before you start painting, make sure that a smaller brush or airbrush is used to complete the details. Large, simple areas can be brushed with a medium bucket brush.
5.Control the amount of paint. In order to ensure the thickness of the coating and the effect of the coating, it is recommended to control the coating not to exceed millimeters at a time.
6.The direction should be smooth. The paint should be applied in the same direction as the date shed. For wooden items, it is best to brush in the direction of the grain. However, in the actual situation, the cross diagonal method can be used in the rapid large-area construction.
7.Avoid station marks. In order to avoid producing transverse brush marks, it is best to apply the same part once to ensure that the coating changes evenly and evenly.
8.Fix the holes in due course and gently remove the paint container and the remaining miniatures.
It is important to note that the paint must be brushed in a well-ventilated environment. If you have any questions or skills about brushing, consult an experienced designer or professional construction agency.
-
The methods and tips for brushing paint are as follows:
1.Preparation:
Before painting, the surface of the wall or woodwork needs to be cleaned and the uneven surface smoothed with sandpaper.
2.Select Brush:
Choose the right brush, it is recommended to use a roller brush or a short-handled brush with a large brush head width for large-area brushing; For small areas, it is recommended to use a long-handled brush with a moderate brush head size.
3.Stirring the paint:
Stir the paint before applying it so that it mixes evenly and achieves the best results.
4.Painting Order:
5.Adjust the paint thickness:
When applying paint, you can choose different paint coating thicknesses and brush sizes according to your needs to achieve the best application results.
6.Avoid dripping:
When applying paint, it is important to take care to avoid over-painting and dripping to avoid unnecessary waste and unsightly appearance.
It is important to note that when applying paint, you should follow the appropriate safety regulations, such as using respirators, gloves and goggles, etc., and keep the room well ventilated. Before applying paint, you should also choose the right paint type and color to suit your needs and preferences. At the same time, according to the area and needs of the brush, choose the appropriate brush and painting technique to achieve the best painting effect.
-
When renovating a house, painting is a very common step to rent. However, many people have paint peeling and uneven brushing when brushing, which affects the aesthetics of the house. To this end, this article will introduce some methods and tips when brushing paint to help you achieve an aesthetically pleasing effect.
First of all, preparation is essential. Before you start painting, make sure that the surface of the wall or furniture is dry and clean. If the paint has been left unused for a while, it should be stirred well to prevent the pigment from settling.
Also make sure you have enough paint and try to avoid adjusting the color multiple times or blending different styles of paint.
Secondly, the choice of brush is very important when it comes to painting. For larger areas, brushing can be done using a flat brush or a roller roller. For smaller areas, you should choose some smaller paint brushes, taking into account the brushing of the corners.
Typically, paint is poured into a tray and the paint is dipped in with a brush before the walls are painted, and the roller can be used to evenly cover a large area.
Secondly, the square footage of the paint is also very important. When brushing the surface, the wall should be painted in the same direction as much as possible, supplemented by small details. If a roller is used, the wet edges should be kept on the surface of the paint that does not dry.
If you need to paint the corners of the walls, you need to brush the delicate corners and corners with a slender brush to avoid plaque.
Finally, pay attention to the order in which the paints are placed. When painting a lattice shed, you should start brushing from top to bottom to prevent missing some details. When painting to a corner or ceiling, you can first paint straight lines and then use a fine brush on both sides of the contact point to delicately paint the corner.
To sum up, when brushing paint, we should pay attention to the full preparation of the preparatory work, choose the right brush and painting equipment, and master the skills and methods of brushing, so that the painting can be beautiful, uniform and the effect can achieve the desired effect.
First of all, it must be polished, then cleaned, and then used putty to make up the place of Kenwa, be sure to use putty, and then polish it after the putty is dry, this time it is to smooth the place where the putty is made, and then use a brush to clean up the table (the place to be painted), and then brush it with white paint, brush it 3 times, brush the paint once to grind it once, and grind off the particles on the table, because there must be that kind of particles when brushing the first 2 times, and you must find a relatively closed place when you paint for the third time, It's best to clean it up first and then put it in, and then brush the last paint, the program is so much, precautions: don't use water when cleaning, the paint shop has the kind of rag that specializes in cleaning the floor, you can buy some, brush it with a brush first, and then check it to be clean, when grinding, you must grind the place you want to paint, don't have too much paint on the brush when you paint, because you are a layman, you can't master the skills, so you have to be less, brush a few more times, take your time, and then you can have more when you brush the desktop, But the first 2 sides are not too much, it is not easy to dry, and it is not good to paint too much on the desktop, and it will crack after a long time. There is white paint in the paint spot, and you can brush it directly when you open it, how can you accompany the putty? >>>More
Paint is a more common decoration material when decorating, it has a lot of functions, can be used to brush walls, brush furniture, etc., but experienced friends know that paint is not easy to smooth when brushing, so how to brush it will be more smooth and beautiful. Next, I will introduce you to how to brush the paint to be smooth and paint purchase tips. >>>More
In general, the wall skin will be shoveled off (batch putty layer) for the decoration of old houses, and the surface of the wall will be damaged due to the aging of the wall skin surface or the demolition and vibration in the early stage of decoration. After shoveling, the surface dust should be washed off with water, and the wall should be brushed after drying. >>>More
With my many years of experience in painting, I have the following two ......First, the paint must be good (such as the Heavenly Maiden, Pentium) Second, the paint base should be scraped with putty (that is, putty prepared with paint).
One year is bright, and three years are somewhat old.