Is it difficult to paint the wall by yourself, and how to paint the wall by yourself

Is it hard to paint the wall yourself? Many people agree that it is not difficult to follow the steps of brushing the wall, follow the following steps: clean the wall, repair the wall, scrape putty, brush the first latex paint, brush the second latex paint, brush the third latex paint, and easily do it yourself.

1. Clean the wall to remove the peeling and loose parts of the wall, and use cement mortar to repair it, shovel the residual ash clean, and then sweep the wall.

2. Repair the wall with plaster to level the wall bumps and potholes, etc., and grind off the protrusions with sandpaper after drying to sweep away the floating dust.

3. Scraping putty The number of times of scraping putty can be determined by the flatness of the wall, generally three times, polyvinyl acetate emulsion for kitchen, toilet and bathroom: cement: water = 1:

5:1 water-resistant putty. The first time with a rubber scraper transverse full scrape, a scraper followed by a scraper, the joint shall not be left behind, each scraper at the end of the end to be clean and neat.

After drying, sandpaper, polish the floating putty and stains, and then clean the wall. The second time with a rubber scraper vertical full scrape, the materials and methods used are the same as the first putty, after drying, the sandpaper is smoothed and cleaned. The third time use a rubber scraper to find the putty or scrape the putty with a steel scraper, scrape the wall flat, and then smooth and polish it with fine sandpaper after drying, and the putty shall not be omitted or worn through.

4. The first time to brush the latex paint, the order is to brush the top plate first and then the wall, and the wall is first up and then down. Clean the wall first, and use a cloth to wipe off the dust on the wall. The latex paint is painted with a pen, and when you use a new pen, remove the floating hairs and unstable hairs on the pen.

Latex paint should be stirred evenly before use, and diluted with water appropriately to prevent the paint from not opening all over the head. After drying, the putty is replenished, and then dried and polished with sandpaper and cleaned.

5. The operation requirements of brushing the second time latex paint are the same as the first time, fully stirring before use, if it is not very thick, it is not appropriate to add water to prevent penetration. After the paint film is dried, use fine sandpaper to polish off the small bumps on the wall and the brush bristles, and clean them after grinding them smooth.

6. The method of brushing the third latex paint is the same as that of the second latex paint. Due to the rapid drying of the latex paint film, it should be operated continuously and quickly, starting from one end and gradually brushing to the other end, and the upper and lower brushes should be connected with each other, and the latter row of pens should be followed by the previous row of pens to avoid the appearance of dry rear joints.

Hello, what are you referring to painting the wall, big white powder, or wall paint, these two samples are not difficult, you can do it yourself, but you must not be proficient if you do it for the first time.

First clean the wall, then scrape the putty, and be sure to polish it after scraping the putty. The next step is to brush the primer, after the primer is brushed for the first time, the defects of the old wall are clear at a glance, and it is necessary to repair them at this time. The last step is to brush the top paint, within 7-10 days after brushing, do not scratch, do not touch the wall, and the indoor refresh of the wall will be successful.

Specific steps introduction: 1. Cleaning the wall wall is very important for indoor refresh of the wall, because stains, floating ash and cracks will directly affect the beauty of the wall, so the old wall should be cleaned before painting. 2. It is recommended to use putty with higher particle fineness and harder texture for indoor refresh of the wall by scraping putty.

Try to stir the putty well and let it sit for another 20 minutes. Use a scraper or spatula to scrape putty, try to use evenly and one-step scraping when scraping, and try not to scrape repeatedly. 3. The sandpaper for grinding the wall is selected according to the hardness and softness of the putty.

After sanding, try to clean the wall to avoid the adhesion of the wall paint being affected by too much dust. 4. If the amount of paint used on the wall is large, you can add an appropriate amount of water to the primer, and the painting process must ensure that the entire wall is brushed with primer and painted evenly. Use the same texture roller for primer and topcoat, because the effect of the primer will directly affect the effect of refreshing the wall in the interior.

5. After the primer is brushed, the defects of the old wall are clear at a glance, and the repair is carried out at this time. Find the flaws, sand them even, and paint the wall with a lighter primer than before. 6. In the process of brushing the topcoat, remember that the paint should not be too thin, which will affect the thickness, hardness and feel of the paint film.

The construction tools should be selected, the bristles of the drum should be fine, not too short, and the paint film can feel delicate. During the painting process, pay attention to the corners of the wall, the position of the stubble and the direction of the painting, so that the interior refresh the wall will not be in vain. 7. Maintenance will generally dry after 4 hours of brushing latex paint, but the paint film has not yet reached a relatively hard degree, at this time, pay attention to 7-10 days, do not scratch, do not touch the wall, so that the indoor refresh of the wall is successful.

1. Basic treatment of old walls: Before decoration, we have to go to the mall to buy some special paint brushes, preferably better quality brushes. In this way, we can paint thicker, so that the original base color can be concealed, and it can also make the paint more durable.

In addition, you need to wipe the old walls clean, you can wipe them with sandpaper before applying latex.

2. Remove the old wall: If there is something on the original wall, we want to clean it up, if there is an uneven place, we need to level it, and then coat it with a layer of white cement to lay a better foundation for the follow-up work. If the wall itself is smooth, we just need to polish it.

Before applying the paint, the paint should be mixed evenly, and then let the paint sit for 20 minutes until the foam on the surface disappears before we can paint the wall.

3. Brush the primer: Before brushing the primer, we need to brush a layer of primer to make the primer. This step should never be omitted, as without paint, the paint on the walls will peel off over time, grow mold, or fade.

When preparing latex coatings, we need to mix water with latex paint in a certain proportion, otherwise it will lead to poor film formation of latex coatings and fail to achieve the decorative effect we expect.

4. Wall repair: After each painting, we have to put it aside until it dries thoroughly, and it generally takes 2-4 hours before painting. Or after applying the latex paint hand, we can touch it with our fingers, and if the paint you are pressing with your fingers is not bonded (in the case of dry acupressure), then you can paint.

The above is the question of how to paint the wall by yourself and related questions, I hope these can be helpful to you and can provide you with some ideas.

Can you paint the walls yourself??Absolutely. During the renovation process, we must paint a little paint.

This is to make our décor brighter, so, in general, we ask the professional staff, but there are many friends who can save a lot of money, so you often choose to do it yourself. So,Can you paint the walls yourself?Can you paint the walls yourself?What should I pay attention to when using paint?

Can you paint the walls yourself??The first thing to do is to clean the walls. Remove dust and paint from floating on it and keep the walls clean and tidy.

Can you paint the walls yourself?Yes, it can be used for the basic treatment of professional grinders. If you choose to use the service immediately, the walls will be cleaned thoroughly. If there is a peeling area, clean the spatula.

2. Add water and white latex to the putty powder to adjust, and the putty powder should be more stirred.

3. Use a blade to scrape the powder putty on the wall, not too thick, try to be even.

4. After the powder putty is dried, the most difficult grinding step must be carried out. Sandpaper is used to sandpaper to polish any irregular spots. In fact, the hardest part of this step is because it's too physical and has a lot of putty. Dust, remember to wear a mask.

5, steps 3 and 4 are repeated n times according to your own needs, but in general they can be 2 to 3 times, provided that they must be dried before repeating.

6. After polishing the putty, you can perform the last step, which is to brush the latex paint. This step is relatively straightforward. You can use a roller or brush to apply latex paint to the wall.

Latex paints can be selected with efficient deodorization and fresh formaldehyde-resistant scent. The color of anti-formaldehyde and anti-formaldehyde all-effect wall paint is safer for health and use.

1, Mix the paint thoroughly in the tank before use, and then mix proportionally. After letting it rest for ten minutes, it can be applied.

2. The unmixed paint can be resealed and stored in a cool place after opening.

3. After the paint is ready, please use it within 4 hours. It is forbidden to return unpainted paint to the bucket.

4. Production date, product name, net content, product ratio, etc. They can be found on the product label.

5. Service life: 12 months (after service life, it can be used after small area test).

6. After using the construction tools, wash them with soap and water.

7. Do not work in wet or cold weather (temperature below 5 degrees Celsius, relative humidity greater than 85%), otherwise the expected coating effect will not be achieved.

The previous introduction was:Can you paint the walls yourself?Notes.

You can get it for free

After more than 20 years of house, the wall skin is definitely not good, because the original wall skin has no cement and no cohesiveness, and it has been crispy for more than 20 years. In the long run, go to the wall skin for cement. But the cost is too great for anyone to afford.

There is no way, only scrape putty to find leveling, and then brush with latex paint, your house workers want 800, which is also reasonable, no one wants to do second-hand old houses, thankless. Now that you've come to this point, buy latex paint and do it yourself. Buy a bucket of Dulux latex paint (please support domestic products) for 300 yuan, 10 pieces of sandpaper (360 mesh), a roller brush (about 20 yuan) and a row of brushes (about 5 yuan).

First level with sandpaper, and level with putty in low places. For the first time, pour out half of it, add 10% to 20% water, stir well, and roll coating. If you can't roll it, use a row of brushes, and it will dry in about one or two hours, and you can brush it a second time, adding about 10% of water.

Buy a paint roller brush and use a roller brush dipped in paint to touch the wall and it's OK.

No, a few dollars per square meter. 600 bucks is fine.