What should I do if the water drain at the bottom of the automatic washing machine is not clean?

This is not that the water in the bucket is not drained clean, because there is a circular plastic ring on the top of the laundry bucket, called the balance ring, which is filled with a certain amount of salt water, the main function is that when the washing machine is in the dehydration program and the clothes are eccentric, that is, when the clothes are uneven or biased to one side of the barrel, the salt water in the balance ring will gather to the opposite side, which can play a balancing role, (the salt water is poured because the salt water is not easy to freeze), the machine has no problem, please feel free to use.

1. First of all, check whether the adjusting rod nut on the drain valve is loose, and whether the tractor cable is loose from the drain valve, resulting in the retractor being unable to pull the drain valve core apart and causing non-drainage.

2. If the fixing nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time.

3. There may be debris blockage in the drain valve or bending and deformation of the drain hose, at this time, unscrew the drain valve cover first and take out the debris.

4. The gap between the drainage rod and the rubber valve becomes larger, as long as the gap between the drainage rod and the rubber valve is appropriately adjusted.

5. The spring in the drain valve is too long or loses its elasticity. Just replace the inner spring.

6. The damping of the moving core of the drainage solenoid valve is too large or the suction force becomes smaller. Remove rust and dirt from the solenoid or replace the drain solenoid valve.

7. If it has not been solved, the computer board may be damaged, and the computer board should be replaced.

8. First check the safety switch, the washing machine is turned on and the program is adjusted to the dehydration state, press the safety switch brake arm to the lowest with hands or tools, if the computer board alarms and the digital tube shows "E1", the safety switch or computer board should be replaced at this time.

9. If the brake arm of the safety switch can be dehydrated normally after pressing it with hands or tools, it means that the power-off distance of the safety switch is low, and the safety switch should be replaced at this time.

10. If in the dehydration state, only the wave wheel rotates and the inner barrel does not rotate, at this time, the tractor should be checked whether the clutch pawl and ratchet wheel have been separated, if not, it is possible that the adjusting rod nut on the drain valve is loose and worn, resulting in insufficient opening distance, at this time, the distance of the adjusting rod should be readjusted, so that the pawl and ratchet of the clutch can be separated.

11. Check whether the clothes in the bucket are placed on one side, and there is a loud noise when the dehydration is shaken, and the cover should be opened at this time to place the clothes evenly.

If the above problems have not been solved, the computer board or clutch may be damaged, and the computer board or clutch should be replaced.

If the drain of the automatic washing machine is not clean, this should be its drainage facility, where there is a fault, you can clean the drain.

The automatic washing machine does not drain cleanly, which may be due to the following reasons: 1. The performance of the water pressure switch is poor or there is air leakage in the air pipeline. The air pressure in the machine becomes smaller, and when the water level in the bucket has not dropped to the specified position, the water pressure switch contact will act in advance, so that the total drainage time is shortened, resulting in unclean drainage.

Just try to find the air line leak and seal it with 401 glue. 2. The water pressure switch is damaged. The solution is to replace the water pressure switch.

3. The drain valve is not in place. Remove the drain valve and reinstall it in place. 4. The drainage time is too short.

Drain for an extended period of time until drained clean.

There is also a reason why the automatic washing machine can drain water, but the drain is not clean, because the drain pipe may be higher than the water outlet hole, if the drain pipe is lowered a little, it is directly placed on the ground. Lower than the drain hole will be clean.

Hope it helps! Kiss.

What happens when the water drain of a fully automatic washing machine is not clean? I think if the water drain is not clean in a fully automatic washing machine, it should be that your drainage system is broken. You can ask the maintenance master to come and have a look.

The drainage of the roller hole washing machine is not clean, which may be due to the following reasons: 1. The performance of the water pressure switch is poor or there is air leakage in the air pipeline. The air pressure in the machine becomes smaller, and when the orange carrying water level in the bucket has not dropped to the specified position, the contact of the water pressure switch will act in advance, so that the total drainage time is shortened, resulting in unclean drainage.

As long as you try to find the air leak in the air line and seal it with 401 glue, you can guess. 2. The water pressure switch is damaged. The solution is to replace the water pressure switch.

3. The drain valve is not in place. Remove the drain valve and reinstall it in place. 4. The drainage time is too short.

Drain for an extended period of time until drained clean.

Open the rear panel of the washing machine, use a screwdriver to remove the screws first and then pick them open, check whether the drain pipe is blocked, if it is not blocked, the drain hole in the inner cylinder is blocked, and the next step is required!

Open the upper cover of the washing machine, there are a total of 4 screws on the upper cover of my washing machine, different models may be different, pay attention not to miss it when disassembling!

After lifting the upper cover, start to disassemble the inner cylinder of the washing machine, first use a screwdriver to remove the fixing screws connected to the upper inner cylinder and the outer cylinder, I have 4 of them. Then remove the fixing Phillips screw at the bottom of the inner cylinder, and remove the bottom cover of the inner cylinder after removal.

After removing the bottom cover, you can see that there are four hex screws under the bottom cover, remove them with a live wrench or socket wrench! Because my washing machine is already installed, I won't see it here!

The key step - at this time, the inner steel drum of the washing machine has been completely separated from the outer plastic bucket, grasp the edge of the inner drum and gently shake it upwards to pull it out, at this time you will see the drainage hole under the outer drum of the washing machine. My washing machine should have two one-dollar coins tightly blocked this hole, so there is a phenomenon that can not drain water, sad ah! Just clean the blockage in the hole, it's that simple!

In this case, you should have a problem with the installation of Haier's washing machine. You can call the after-sales service of Haier automatic washing machines** and let professional maintenance personnel adjust it for you. This will not delay your normal use.

The washing machine is unbalanced, the drain pipe is blocked, and the drain outlet position is too high.

Hello, the drainage of the rolling hole washing machine is not clean, which is due to the following reasons: 1. The performance of the water pressure switch is poor or there is air leakage on the air pipe Fengpi Road. The air pressure in the machine becomes smaller, and when the water level in the bucket has not dropped to the specified position, the water pressure switch contact will act in advance, so that the total drainage time will be shortened, resulting in unclean drainage.

Just try to find the air line leak and seal it with 401 glue. 2. The water pressure switch is damaged. The solution to the fraud of banking is to replace the water pressure switch.

3. The drain valve is not in place. Remove the drain valve and reinstall it in place. 4. The drainage time is too short.

Extend the drain time until it is drained clean.

Summary. This is not that the water in the bucket is not drained clean, because there is a circular plastic ring on the top of the laundry bucket, called the balance ring, which is filled with a certain amount of salt water, the main function is that when the washing machine is in the dehydration program and the clothes are eccentric, that is, when the clothes are uneven or biased to one side of the barrel, the salt water in the balance ring will gather to the opposite side, which can play a balancing role, (the salt water is poured because the salt water is not easy to freeze), the machine has no problem, please feel free to use.

This is not that the water in the bucket is not buried and drained, but because there is a circular plastic ring on the top of the laundry bucket, called the balance ring, which is filled with a certain amount of salt water, the main function is that when the washing machine is in the dehydration program and the clothes are eccentric, that is, when the clothes are uneven or biased to one side of the barrel, the salt water in the balance ring will gather to the opposite side, which can play a balancing role.

We don't have salt water in it.

When I shake the drum, there is a sound of water underneath.

Put the washing machine high and drain it at the low point, no, the washing machine will be idle for a few minutes, and it will be discharged.