What to do if the washing machine wheel slips, what happens if the washing machine s wheel slips

The washing machine wheel slipped for two reasons:

1. The pulley has been used for a long time, the wear is large, the friction is reduced, and if it is used frequently, the perimeter of the pulley tension will increase, and it is necessary to replace the new pulley.

2. The bearing of the laundry bucket drum is worn, or the fastening screws are loose and not firmly fixed, and there will also be slippage.

When the washing machine program enters the washing state, the washing machine motor rotates normally, but the wave wheel does not rotate.

Cause of failure and repair method: The fault mostly occurs in the mechanical transmission part between the motor and the wave wheel.

The specific reasons and ways to deal with them are:

1. The fastening screws of the motor pulley, clutch pulley and wave pulley are loose, slippery or broken. Just re-tighten or replace the fastening screws; If the square hole of the wave wheel is rounded, the wave wheel should be replaced.

2. The V-belt slips or falls off. As long as the distance between the motor and the clutch is appropriately increased, and some rosin powder is rubbed on the V-belt to increase the friction. If the V-belt is aged and deformed, the V-belt should be replaced.

3. If the parts of the clutch deceleration mechanism are worn or damaged, the clutch assembly should be replaced.

Causes and solutions for washing machine wheel slippage.

1. The pulley has been used for a long time, the wear is large, the friction is reduced, and if it is used frequently, the perimeter of the pulley tension will increase, and it is necessary to replace the new pulley.

2. The bearing of the laundry drum is worn, or the fastening screw is loose, and the fixing is not firm, and there will be slippage.

How a washing machine works with a wheel.

It is driven by the motor to rotate the wave wheel through belt deceleration, and the timer or computer controls the wave wheel to rotate forward and backward to stir water, detergent and clothes, and the clothes to be washed are stirred and rubbed by reciprocating in the washing bucket under the mechanical action of the wave wheel rotation and the chemical action of the detergent aqueous solution.

The characteristics of the washing machine are:

The washing ratio is relatively high, and the corresponding wear rate is higher than that of front-loading washing machines. It is suitable for washing general cotton, linen, chemical fiber and other fabrics.

Analysis & Repair].

The wave wheel and the spindle are generally matched with a square hole. Due to the small relative movement of the wave wheel when it runs forward and in reverse, the four-sided knife edge of the square mandrel repeatedly grinds the nylon inserts. When worn to a certain extent, the roller will slip.

When repairing, two pieces are embedded in the square hole worn by the wave wheelmillimeters of copper sheets, so that the square hole is restored. Here's how:

Use a small driver to dig a groove 10 mm deep, mm thick and 18 mm long on both sides of the hole to be embedded with copper sheet, and then insert a copper sheet of the same size into the groove. You can also use a small hammer to gently knock it in, but not too hard, to prevent the square hole of the wave wheel from swelling and cracking. If the shaft of the wave wheel is broken, it should be replaced with a new one.

This method can also be used to repair the square holes of large pulleys that are worn.

Tighten the belt first, and if it doesn't work, change the belt.

Adjust the wheel base. The replacement belt that cannot be adjusted.

There are two reasons for this:

First, the pulley has been used for a long time, the wear is large, the friction is reduced, and if it is used frequently, the perimeter of the pulley tension will increase, and it is necessary to replace the new pulley.

Second, the bearing of the laundry bucket drum is worn, or the fastening screws are loose and not firmly fixed, and there will also be slippage.

The belt is loose, and the distance between the motor and the runner can be adjusted.

It should be that the belt inside is loose.

The main reason for the slippage of the wheel of the washing machine is that it has been used for a long time.

Reasons for the slippage of the wheels of the washing machine:

1. The pulley has been used for a long time, and the wear is large, and the friction is large.

Decreased, often used, the perimeter of the pulley tension loosening will increase, and it is necessary to replace the pulley with a new one.

2. The bearing of the laundry drum is worn, or the fastening screws are loose and not firmly fixed, and there will also be slippage and rotten nuclear shooting.

Precautions for the slippage of the wheel of the washing machine:

1. The tightness of the transmission belt of the washing machine has a great impact on the working state of the washing machine. If the belt is too tight, it will cause a lot of noise and increase the input power. If the belt is too loose and leaky, the speed of the roller will be slowed down, and the clothes will not be able to roll or the number of times will be reduced.

2. The method of checking the tightness of the belt is to press the middle of one side of the belt with one finger, and the belt is close to the other side, and it is about 10 mm to move inward, and the tightness can be considered appropriate.

3. The method of adjusting the tightness of the belt of the washing machine: loosen the fixing screws of the motor base, move the motor base to the appropriate position along the long hole of the screw, and tighten the screws.

Be careful when tapping and don't hit too hard. The main purpose is to loosen the rust inside. 2.

Then use a screwdriver to tighten the screws vertically, paying attention to the angle. Try to tighten the screws as hard as possible so that the screws in the middle can be unscrewed. 3.

If the screws are difficult to unscrew, you can also apply some lubricating oil to the screws by hand and unscrew them with a screwdriver after a while.

The washing machine wave wheel fell off, and under normal conditions, a screw fixed it on the wave wheel shaft in the middle of the wave wheel, and the screw was loosened for some reason, and the wave wheel was taken off by the reaction force during washing.

To retrieve the missing screws, align the square hole at the bottom of the wave wheel with the square end of the shaft, put the wave wheel back and fix it tightly with screws.

This answer applies to most brands of washing machine models such as Midea, Haier, Little Swan, etc.

【Knowledge Expansion】How to clean the washing machine:

1. Prepare professional cleaning agent. Choosing a professional cleaner can reduce the damage to the fuselage.

2. Pour the cleaning agent into the water, mix the cleaning agent and water in the ratio of 1:2 and then pour it into the washing machine, enter the working state of laundry, repeat at least 2 times, and then the dirt can be removed.

3. Clean the filter. There is another place to pay attention to is the filter, this place should not be ignored, after cleaning the fuselage, take out the filter to clean, and you can use a brush to brush it clean when cleaning. This filter must be cleaned frequently, otherwise it is easy to clog and affect work efficiency.

4. Clean the drum. Prepare rice vinegar, baking soda, pasteurizer, moisten a towel completely with vinegar, put it in the washing machine, and turn on the dehydration mode, which is equivalent to spraying vinegar on the inside wall of the washing machine. Then turn the washing machine to its maximum, dissolve the baking soda in the water and soak for 2 hours.

Then turn the washing machine to normal washing mode for rinsing. Finally, pour the pasteurizer into the water according to the stated proportion, turn on the rinse mode and wash it twice, and you're done.

If the gear is damaged, the gear can be replaced directly; If the wave wheel is damaged, replace it with a new one; If the mechanical part is stuck due to rust, disassemble the motor and properly lubricate the rotor. There are mainly the following reasons: 1. If the wave wheel floats up when washing clothes, it means that the wave wheel is broken, or the gear may have worked for a long time, the grinding is loose, and it begins to slip, resulting in the wave wheel loosening.

2. Check whether the wave wheel is damaged, if it is not powered on, it can be easily rotated to the wave wheel that is damaged. 3. If it is because there is no maintenance for a long time, the mechanical part is stuck due to rust, causing the washing machine wave wheel to break. Suggested Treatment:

1. If the gear is damaged, the gear can be replaced directly, pay attention to the gear is divided into eleven teeth and ten teeth, eleven teeth are more common, pay attention to the selection of appropriate gear. 2. If the wave wheel is damaged, directly remove the wave wheel and replace it with a new one, when replacing it yourself, if there is no accurate judgment on its size, you can take the old parts to the home appliance accessories and buy a new one, how to remove it and how to install it. If the washing machine is under warranty, contact the manufacturer and ask the manufacturer to send someone to repair it.

3. Disassemble the motor directly and properly coat the rotor with some lubricating oil. Or replace the lower rotating bearing and reassemble it again. If you have checked all of the above and found no problems, you should contact a professional for repair to avoid unnecessary losses.

Generally speaking, the washing machine has been used for too long, and the screws are loosened because the washing machine often vibrates; or the gap between the screw and the fit becomes larger and worn; Or the teeth on the fixing hole between the wave wheel and the motor shaft are ground off. It needs to be analyzed in detail, and then it can be replaced with new parts, and the components that need to be repaired can be repaired.

1. The wave wheel sometimes feels tightened, but in fact it is not necessarily, you need to check it, otherwise you will feel tightened every time, and as soon as the washing machine works, it vibrates, and the wave wheel falls off. Under normal conditions, a screw will fix the center of the wave wheel on the wave wheel shaft, the screw is loose, and the working wave wheel of the washing machine will fall off after being subjected to the reaction force, pay attention to the screw needs to be tightened with relevant tools, and try your best until it cannot be screwed.

2. If the wave wheel is not tightened, it will automatically fall off, and you can use a packing belt for the outer box of the washing machine to wear it under the wave wheel, and lift it up forcefully to lift the wave wheel.

3. There is also a possibility that there is a problem with the wave wheel itself. Inspect the central shaft of the wave wheel to see if the pinion is worn, and if so, replace the wave wheel. The installation of the wave wheel is not difficult, you only need to buy one according to the laundry model, remove the bad one and install it.

Note that when installing the wave, do not damage other parts, and the bottom plane of the machine should be consistent with the surface of the wave wheel.