What does hollow floor tile mean? What are the consequences of hollow floor tiles?

There are many reasons for the hollowing on the tiles, and the indoor tile paste has high requirements for auxiliary materials, and the auxiliary materials for ceramic tiles are not suitable for ceramic tile materials. The indoor temperature is low, the workers operate irregularly, and if the tiles are not pasted in the order of the process, the tile hollow drum may fall off. During the decoration process, ceramic tiles, tile accessories, a few years ago the tiles were cement mortar, the sand in the accessories, the proportion of the two materials is normal, and the tiles are very strong.

The ratio of the two materials is unbalanced or the sand is too fine, and the effect of tiling is not good. Cement mortar is not suitable for tile materials.

The empty drum falls off in a small area, the loose tiles around it are shoveled off together, the cement mortar layer does not fall off with the tiles, the wall surface is flat, and the tiles can be re-pasted. Remove the dust from the wall, rub the glue on the wall twice, apply glue on the wall, mainly on the tiles, etc., better apply glue, glue on the wall, and prevent the tiles from falling on the hollow drum. Using a small roller or board brush, apply the tile evenly on the back of the tile, etc., and apply it twice on the back, and then apply the tile after the adhesive such as milky white gradually becomes transparent.

The construction is simple and convenient, and it is an ideal decoration material for repairing subsidized tiles. Most of the area where the hollow drum falls off is that the cement mortar layer and the tile fall off together, and in this case, it is not recommended to apply the tile.

Tile adhesive repairing tiles can be selected in small packages, and the back of the tiles can be evenly coated with adhesive mortar, which can be constructed, or the tiles can be directly pasted on the wall. It can be used both indoors and outdoors. Water-based materials, environmental protection, quality certification, household tile adhesion, ideal tile accessories repair, etc.

This process of coating the cement mortar with a mud bond layer before laying it is not suitable. Some construction personnel sprinkle cement powder after sprinkling water, the cement powder is sprinkled unevenly, and eventually there is unevenness or leakage, and the mud concentration is not easy to control, too diluted or too thick, which will affect the paste effect. The process of painting cement slurry should be adapted to the process of paving floor tiles, then the mud has dried, and the floor tiles can no longer be pasted.

On the contrary, mud can act as an isolation, and the appearance of the phenomenon of announcements is inevitable.

The quality problem of hollow or loose floor tiles is relatively simple, clean the foundation surface to ensure that there is no debris and stagnant water, fully mix the dry powder and water, stir evenly, and finally when the particles do not precipitate, stop for about 5 minutes, and then mix for about 2 minutes. Do not blank, and after 10 minutes rub out additional gaps.

It is the hollowing phenomenon between the floor tile and the structural layer (concrete or brick wall) due to the poor pasting and bonding, commonly known as "two-layer skin".

Floor tile hollowing means that the floor tile is empty underneath, and the floor tile is not in contact with the ground, and there is a gap in the middle.

Floor tile hollowing: refers to the cement oil of the adhesive layer is not full during the construction process, resulting in the void between the adhesive layer and the tile surface.

According to my family's experience, it was very troublesome to turn the floor tiles that had just been drilled up. Hollow floor tiles should be redone. Because empty.

The floor tiles of the drum will affect the floor tiles without hollowing, and when the weather changes, because the bricks and the ground are layered, the heat and cold shrinkage are not.

It will also cause the floor tile holes to rise, and the cement will become abnormal after a long time because the cement is not attached to the floor tiles.

The hardness of the hard, in the future, when you have a problem with the floor tiles, it will become very troublesome to redo the part, and the hollow floor tiles will definitely be holed.

It's just that the time hasn't come yet. So I advise you to redo it to prevent future troubles.

1. Due to the uneven force of the ceramic tile adhesive layer, or the inflation coefficient is inconsistent, it will lead to the cracking of the ceramic tile surface layer. This phenomenon is very common, that is, the tiles are hollow and prone to cracking.

It refers to a phenomenon that after laying the floor tiles for a period of time, there is a phenomenon that the top is topped, and after laying for a period of time, it is necessary to apply some repair solution on it, and there should not be too much water on it to avoid it.

The floor tiles suddenly bulged, probably due to the fact that the floor tiles were not very good, due to some external factors. If you want to avoid this phenomenon, you must do all the work when laying floor tiles, and you must also let some relevant masters check it clearly.

If there is some air between the tile and the plaster layer, the phenomenon of bulging will occur. Be sure to clean the dust at the beginning and choose the right glue.

It is that there is a hollow sound when the floor tiles are knocked, and the mud and sand filling under the floor tiles is not particularly good. You can sprinkle some water when laying, which can make the sediment more solid, which usually does not occur.

It is that after laying the floor tiles, there is an uneven situation, there is a bulge on the floor, and you need to lay it neatly when laying the floor, you don't put too heavy items.

1. The time for soaking in water for floor tiles is insufficient. Due to the different types of floor tiles, the requirements for paving are also different, such as 800*800 large tiles do not need to be soaked in water, and can be paved directly. And like 300 * 300 ordinary clay bricks, before paving to soak in water for a sufficient time, and then take it out to dry, to ensure the moisture content of the floor tiles can be paved, if not soaked in water or soaked in water time is not enough, it is easy to appear hollow.

2. The cement label is not enough. We all know that the paving tiles are to use cement mortar, and the ratio of cement and sand is required to be 1:, which can ensure the adhesion of cement mortar to the greatest extent.

However, in the construction process, some people cut corners to reduce the ratio, reduce the content of cement, and increase the amount of sand, so that there can be a large area of hollowing of floor tiles caused by unqualified cement mortar.

3. The ground is not sprinkled. Before the floor tile paving, it is necessary to sprinkle water on the ground, so that the original ground can ensure the moisture content, so that the new cement mortar is fully consistent with the moisture content of the original ground, so that the cement mortar of the floor tile paving is firmly bonded with the original ground.

4. There are no seams left in the paving of floor tiles. When paving floor tiles, it is necessary to reserve a gap of millimeters, which is to prevent the cement from expanding in the drying process, resulting in the deformation of the tiles, thus causing the phenomenon of hollowing. However, some people often feel that the floor tiles they have purchased do not need to reserve gaps when paving, nor do they want to have gaps, so they do the so-called seamless construction.

5. The floor tiles are not dry and stressed. After the construction of floor tiles, cement mortar is required for 2-5 days of ventilation and drying time, but some people are anxious, the first day is paved, the next day will go up to step on casually, or put heavy objects on the floor tiles, resulting in a decline in the adhesion between Na Xianhuai floor tiles and cement mortar, and some areas will be loose, and there will naturally be a hollowing phenomenon.

It is relatively common for floor tiles to appear hollow, and usually appear within a period of time after the renovation is completed. Floor tile hollowing has a great impact on the decoration and living quality of the home, so it needs to be dealt with in time. Here's why the floor tiles are hollow:

1.The grassroots level is uneven.

The unevenness of the ground foundation is the most important factor that causes the tile to be hollow. Before laying bricks on the ground, it is necessary to ensure that the base layer is level, otherwise there will be problems such as brick bulging or subsidence after laying bricks on the ground, which will lead to hollowing.

2.Insufficient or uneven adhesive.

In the process of tile pasting, insufficient or uneven adhesive will lead to the adhesive between the tile and the ground is not tight. Once the tiles are subjected to force or temperature changes and other reasons cause small displacements of tiles, hollowing will occur.

3.The environment is humid.

The correlation between bricks and the environment is great, if it is constructed in a high humidity or even a humid environment, it is easy to lead to the hollowing of the tiles pasted. At the same time, if too much moisture is used in the adhesive when the environment is humid, the bond will not be strong. This means that during installation, it is essential to ensure that the floor chamber is clean, dry and not wet.

4.The quality of the tile itself.

There are some poor quality tiles on the market, which are of poor quality and easy to crack, and even deform after paving, resulting in hollowing. Therefore, before construction, it is necessary to choose high-quality tiles to ensure the quality of the floor and the results of subsequent use.

5.temperature changes and object weights.

As the air temperature and temperature change, objects on the ground may twist and move, in which case the adhesive holding the tiles in place may loosen, resulting in hollowing.

In short, if your home floor tiles are hollow, you can solve the problem by replacing the tiles or re-surfacing them. For construction, we must pay attention to the smoothness and dryness of the base layer, choose high-quality tiles, and strictly control the amount. If our home floor tiles are emptied and removed, and new tiles are paved, we must carefully check the process to avoid the same problem.

Summary. Hello Kiss is happy to answer this question for you. <> What causes hollow floor tiles:

Tile hollowing is a construction problem, and there is no necessary connection with the tile itself. The reasons for this problem are generally: 1. The wall is too dry and the moisture is absorbed too quickly.

2. The time for the tile to soak in water is not enough, or after taking it out of the water, the water control time is too short, and there is too much moisture in the tile. 3. The cement slurry is not evenly scraped in batches, and the compactness is not enough. 4. There are problems with cement or tile adhesives.

Hello Kiss is happy to answer this question for you. <>What is the cause of the empty drum of the floor tiles: the hollow drum of the tiles is a construction problem, and there is no necessary connection with the void of the tiles themselves.

The reasons for this problem are generally: 1. The wall is too dry and the moisture is absorbed too quickly. 2. The time for the tile to soak in water is not enough, or after taking it out of the water god burn, the water control time is too short, and there is too much moisture in the tile.

3. The cement slurry is not evenly scraped in batches, and the compactness is not enough. 4. There are problems with cement or tile adhesives.

Is there anything to do with mop humidity?

Dear, no.