How to lay floor tiles without hollow drums, and can wooden floors be laid on top of hollow floor ti

The paving method of ceramic tiles is actually very simple, but the details of paving are often easy to be ignored, resulting in the problem of tile hollowing, so the following points should be paid attention to when paving: 1. The coating of cement should be uniform and full. The method of tile laying is actually very simple!

But the simpler it is, the more detailed it is, the more problems will occur, just from a plastering cement mortar, whether it is empty or not depends entirely on it. Cement mortar should be evenly smeared and full, and the most important part is often the four sides of the brick, which often makes many people too negligent. 2. Apply the cement evenly at the upper end of the brick to avoid hollowing.

After the wall bricks are pasted on the wall, it takes some time for the cement to solidify, there will be sinking and solidifying, so the key link is at the upper end of the wall bricks, just falling to the sinking and solidifying, look at the upper position of the top of the brick at the bottom of the first brick, it can be seen that it is not the cement mortar sinking, and it is often easy to appear hollow here. 3. The grooves on the four sides of the tile should be filled with cement to saturate. Cement mortar should fill the gaps on the four sides!

Special attention should be paid to the fact that when the back of the tile is full of mortar, it should be plastered into a hypotenuse on the four periphery of the tile, and leave some gaps in the middle, so that when pressing and tapping the tile, it will not cause the mortar to overflow everywhere, and the mortar can be full, and the tile and the wall are firmly combined. 4. Wipe the cement mortar of the brick joint clean to avoid the joint agent turning black. Regarding the problem of caulk, it is best to let the mason immediately wipe the cement mortar of the brick joints after laying a piece, which will help the caulk not to turn black immediately in the later stage.

5. Measure the horizontality and verticality of the tiles. Especially when paving wall tiles, it is best to measure each layer to keep it neat and beautiful.

As long as the mortar is paved, the bricks are laid flat on the semi-dry cement and beaten with a sponge to squeeze out the bubbles in the cement, basically there will be no hollowing.

I see that the masters are dry hard cement mortar after the tile is buckled up (note that the cement is not smeared for the time being) and placed flat, and then lightly buckle the tile, the sound of the empty place is obviously different.

When laying floor tiles, put the dry hard cement mortar on the tile (note that the cement is not smeared for the time being) and put it flat, and then lightly buckle the tile, the sound of the empty place is obviously different. Readjust to confirm that there is no problem, and then apply the cement paving.

This is allowed to have a hollow drum rate, and there are fewer dry paved hollow drums.

First, the cement and sand are paved and scraped, and the bricks are laid.

Find a good master to shop not empty drums.

How to lay floor tiles so that they will not be hollow, the decoration master will teach you the correct method, and the tiles will no longer be hollow.

1. Avoid excessive water absorption of ceramic tiles.

When buying ceramic tiles, you need to focus on checking the water absorption rate of ceramic tiles. Place water on the back of the tile and see how quickly the water soaks out. - Generally speaking, the slower the water absorption, the denser the tile.

The faster the water absorption, the more sparse the density of the tile and the higher the water absorption. When purchasing ceramic tiles, you need to choose a product with a water absorption rate within the standard range. If the water absorption rate is too high, it is easy to absorb water and expand after use, resulting in the phenomenon of hollow drum falling off.

Hollow drum performance: The hollow drum caused by the excessive water absorption of the tile is generally from the edge of the arch and falls off, and is often accompanied by small and round cracks on the surface of the tile. The responsibility for this kind of tile hollowing is mainly in the manufacturer, not in the construction unit.

2. Avoid the back texture of the tile is too shallow.

In order to fit closely with the wall, the back of the tile is generally designed with a texture. When the texture is relatively deep, it can ensure that the ceramic tile and the cement mortar layer will not fall off when they are partially separated. Therefore, it is best not to buy the back pattern of the ceramic tile too shallow, too simple.

3. It is best to choose No. 325 for cement.

At present, the cement produced in China generally has several grades such as 225. The production of different grades of cement is to meet the needs of making different grades of concrete. The cement used for home decoration is generally 325, because the cement for decoration does not need to bear too much force and does not require high-grade cement.

In addition, it is necessary to carefully identify the quality of cement to avoid the selection of inferior cement.

4. Sand is best selected for sand.

Sand can generally be divided into four types: extra-fine sand, fine sand, medium sand and coarse sand. Generally speaking, the coarser the sand, the higher the strength of the cement mortar, but if the strength is too high, it will also lead to some undesirable results, such as cracking of the ground leveled with it. The sand that is too fine does not have a strong adsorption capacity, and cannot produce large friction and stick to the tile.

Therefore, it is recommended to use medium sand in home decoration, and the particle thickness of medium sand is very suitable for use in cement mortar, and its particle size is.

5. The ratio of cement and sand should be appropriate.

In home decoration, the floor tiles are generally dry paved, and the cement and sand are mixed with a small amount of water in a ratio of 1:3. The wall tiles are generally wet paved, and the ratio of cement and sand is 1:

Mix the ratio of 2 and mix well with water. If the ratio of cement mortar is too high, it will lead to excessive water loss after drying, resulting in hollowing of tiles.

Hello, dear, I am happy to answer for you: can you lay a wooden floor on the floor tile hollow? A:

The wooden floor can not be laid on the hollow drum of the kiss floor tile, and the tiles of the hollow drum are easy to be crushed. The hollowing of the floor tile belongs to the construction quality problem. Usually, it is necessary to remove the hollow tiles and re-pavement.

The hollow floor tile wall can be paved with wooden floor for a short time, because there are often people walking on the wooden floor for a long time, the vibration load of people walking is transmitted to the hollow drum floor tile through the wooden floor, it is easy to cause damage to the floor tiles, and the damaged floor tiles sail high finger posture will be suspended, and the wooden floor is easy to break on the suspended ground.

Summary. What to do with floor tile hollowing Hello, dear, <>

How to deal with the floor hollow drum: 1. The hollow drum treatment method at the corner of the floor: grouting to fill the void.

The method of pouring cement mortar directly on the four corners of the floor tiles is very time-saving and labor-saving, and it will not damage the floor tiles. 2. Hollow drum treatment in the middle of the floor: pry brick and repavement.

If the middle of the floor tile is hollow, you can use a suction cup to suck out the floor tile, and then replace the floor tile with a new one and re-lay it according to the specifications. 3. Large-area hollow drum treatment: there is no way to remedy it, but to pry off all the tiles on the whole surface and redo the base layer.

The large-scale hollowing is caused by improper construction, and the construction party should be held responsible. 4. Hollow drum shedding treatment method: hollow drum falling off, proving that there is loosening between the floor tile and the cement mortar layer, resulting in delamination, at this time, you can use a shovel and other tools to clean the cement mortar layer, reapply the cement mortar, and then pave.

5. The degree is lighter and the location is more biased: it can not be treated. If the hollowing of the floor is only a slight phenomenon and does not affect the use, it is recommended to consider not treating it.

Hope it helps!

What to do if the floor tiles are hollow.

How can the floor tiles be hollow and stupid Hello, dear, <>

How to deal with the floor hollow drum: 1. The floor side cavity accompanies the corner hollow drum treatment method: grouting to fill the void.

The method of pouring cement mortar directly on the four corners of the floor tiles is very time-saving and labor-saving, and it will not damage the floor tiles. 2. Hollow drum treatment in the middle of the floor: pry brick and repavement.

If the middle part of the floor tile is hollow, you can use a suction cup to suck out the floor tile, and then replace the floor tile with a new one and re-lay it according to the specifications. 3. Large-area hollow drum treatment: there is no way to remedy it, but to pry off all the tiles on the whole surface and redo the base layer.

The large-scale hollowing is caused by improper construction, and the construction party should be held responsible. 4. Hollow drum shedding treatment method: hollow drum falling off, proving that there is loosening between the floor tile and the cement mortar layer, resulting in delamination, at this time, you can use a shovel and other tools to clean the cement mortar layer, reapply the cement mortar, and then pave.

5. The degree is lighter and the location is more biased: it can not be treated. If the hollowing of the floor is only a slight phenomenon and does not affect the use, it is recommended to consider not treating it.

Hope it helps!

What if I don't want to smash bricks in the living room.

It is exactly the place to walk.

Hello, dear, <>

Treatment: grouting stove to fill the void. Directly on the four corner edges of the floor tiles, the method of pouring cement slurry is very time-saving and labor-saving, and it will not damage the floor tiles. Or Sun Zhi re-changed, I hope it can help you!

1. The base layer of paving floor tiles needs to be dealt with: one of the main reasons for the hollowing of floor tiles is the way of paving, and the method will also cause the floor tiles to be hollow. Therefore, when laying floor tiles, the base layer should be cleaned first, and the wall base layer should be wet in advance, and the humidity should be about 30-70%.

2. Floor tile cleaning and soaking treatment: Secondly, the surface of the floor tile should also be kept clean, and stains should be dealt with in time. Then soak it in water, about 2 hours, wait until the floor tiles are not bubbling, take it out, and then pave it after drying.

3. Cement mortar needs to be full and uniform: we all know that accessories are an indispensable part of floor tiles, commonly used accessories are: cement, mortar, etc., these accessories must be evenly blended to avoid hollowing floor tiles.

Moreover, after the floor tiles are pasted, it takes time for the cement to solidify, so at this time, it is necessary to carefully observe whether the cement will sink and solidify.

4. Reserve enough expansion joints: When the floor tiles are heated, there will be thermal expansion and cold contraction, so in order to avoid the occurrence of hollowing of the floor tiles. When laying floor tiles, be sure to reserve a gap of 2-5mm to avoid the floor tiles being heated, resulting in slippery floor tiles hollowing or falling off.

The above is how to avoid hollowing floor tiles, I hope it will help you.

First, the ground brick hollow drum treatment method:

1. If the situation of the hollow drum is not very serious, only the corners are slightly warped, then we can use tools to pry up along the gaps in the corners, and then pour the prepared cement slurry into the gaps, and then press it tightly with a pressure plate, and wait for the cement slurry to solidify.

2. If the hollowing situation is very serious, then it is best for us to remove the problematic floor tiles, clean up the mud on the back, and then re-apply the cement slurry and lay it on the ground.

Second, the method of choosing floor tiles:

1. You can choose the right floor tiles according to the style of your home, if the decoration style is more plain and concise, then we can choose white marble tiles, which are unified with the style; If the style is more ornate, we can lay more colorful and textured floor tiles in the home.

2. The selected floor tiles should have good anti-slip performance, because the surface of most floor tiles is very smooth, and sometimes it is easy to fall, which is very dangerous, especially in families with the elderly, children and pregnant women.

3. The floor tiles should also have good water resistance, because we often mop and wash the ground, if the floor tiles are easy to absorb water, then expansion and deformation will occur.

4. We should also pay attention to the quality of floor tiles, and do not buy unqualified three-no products for small cheapness, so that the problem of breaking often occurs when used in the future. Therefore, when buying floor tiles at the beginning, it is necessary to choose those brands of floor tiles that are more famous, so as to have quality assurance.

Hello! For different hollow drum situations, there are the following three treatment methods:

If the floor tile is a partial hollow drum in the corner, you can remove the filler of the surrounding seam of the floor tile hollow drum, pour cement mortar, and tap the hollow drum of the floor tile to let the cement slurry infiltrate and repair the hollow drum.

If it is a single floor tile hollow, you can remove the filler around the floor tile, take out the floor tile with a suction cup, cut off the paste layer, and paste it again.

If the floor tiles are hollow in a large area, they can only be shoveled off and re-paved.

If the impact is not large, it can be left untreated. The hollowing of floor tiles is generally caused by insufficient cement grouting, and the best way is to remove the old ones and re-grout them.