Will the floor tiles be hollowed out when they are paved with tile adhesive? On what basis?

Updated on home 2024-07-14
15 answers
  1. Anonymous users2024-02-12

    Tile adhesive for floor tiles.

    Paving will be hollow, basis: tile adhesive is commonly known as tile adhesive, it is based on the traditional mixed mortar to add glue and the rest of my admixtures to update the production of a common use of ceramic tile raw materials. This kind of raw material has good characteristics, and the quality of floor tile parquet can be better ensured.

    Because the tile glue is glued to the glue, it has a higher adhesion than the traditional cement slurry, which determines the adhesion between the tile glue and the back of the floor tile, and its combination with the pavement is greater than the general cement mortar.

    From this point of view, the tile adhesive itself will be more beneficial for manipulating the wall hollow.

    of the generation. The thin paste is the thin paste method that we apply tile adhesive to stick to the floor tiles.

    This is the use of a sawtooth scraper dipped in a certain amount of tile glue scraped on the back of the floor tiles, the same on the ground is the use of a sawtooth scraper to scrape a layer of tile glue, and finally this aspect of the floor tiles parquet onto the road surface of the tile glue, with a rubber hammer. Therefore, in terms of this characteristic, the raw material itself will be easy to compact. It is not easy to have a mixture of mortar, which is very easy to reproduce, and it is not tightly compact, causing the wall to be hollow.

    The paving of tile adhesive must be thin. Therefore, if we use tile glue for the floor tiles on the ground, we must make the flatness of the road surface.

    The ground is leveled to within 5mm to prevent everyone from building tiles.

    It is difficult to level the ground.

    The tile adhesive we use can not add concrete or water at will. It must be applied after mixing evenly according to its preparation. The application of tile adhesive products should be mixed in accordance with its regulations.

    Generally, it is mixed in 2 times. Leave it for a period of time, and the rules for this operation must be implemented. Otherwise, it will cause the tile adhesive to not be able to achieve its proper characteristics.

    Although we have applied tile adhesive to pave the floor tiles, there may be hollow walls in the middle and late stages. Many good friends think that it is the problem of tile adhesive, in fact, most of the factors are not tile adhesive, but the bottom layer of everyone's road surface and the back of the wall tiles. The proportion of factors that contribute to bulging at these two levels is very high.

    There is a significant lack of hardness in the surface layer of the bottom layer of the pavement. For example, sand on the cement floor.

    The pavement is not cleaned and tidy, resulting in the tile adhesive not being able to blend with the bottom layer. This mainly means that we have not cleaned the road surface before we put the floor tiles. The most appropriate behavior should be to wash it with tap water and dry it before subsidizing it.

    Before laying floor tiles, you should check whether the pavement has compressive strength.

    Where there are deficiencies, for the places where the compressive strength is insufficient, I have come up with a proposal to carry out chiseling, and then apply mixed mortar to make the road surface again. Before you stick the floor tiles, be sure to clean the road surface. My proposal is to pour a layer of cement mortar on the ground to improve the adhesion of the road surface.

  2. Anonymous users2024-02-11

    Under normal circumstances, there will be no hollowing, and floor tile glue is also a relatively mature adhesive for floor tiles; If there is a hollowing phenomenon, it may be due to improper selection of tile adhesive, on the other hand, it may also be an error in the construction method of the construction worker.

  3. Anonymous users2024-02-10

    Of course not. We are using the tile adhesive to pave the tile, we must ensure that the glue on the back of the tile is full of grout, and then we must be sure to knock it down, so that it will not be empty.

  4. Anonymous users2024-02-09

    There is this possibility, tile adhesive will also occur hollowing, which is related to the situation of the ground.

  5. Anonymous users2024-02-08

    Household tile adhesives.

    The tiles pasted have hollow drums.

    The reason is: the tile glue can not stick to the wall, the solidified mortar layer will fall off as soon as you shovel, and there is no stickiness at all.

    The situation of hollowing is related to the quality of the product, and may also be related to the unclean treatment of the base surface and the non-standard ratio of powder and water. When choosing tile adhesive, it is necessary to consider the degree of vitrification of the tile piece and choose the appropriate type of tile adhesive; Tile adhesive should be used with stirring, and the use time should be controlled within 2 hours;

    Tile adhesive should never be mixed with cement, tile adhesive is flexible.

    Cement is a thermal expansion and contraction.

    Very powerful rigid materials, the two cancel each other, and there will be a situation of hollowing out the bricks;

  6. Anonymous users2024-02-07

    Not necessarily because of the poor quality of the tiles, there are mainly the following reasons for the hollowing of the tiles at home

    1. The putty layer is not cleaned, and the cement mortar and the wall are not firmly bonded.

    2. The seams are not enough, the tiles are squeezed with each other, generally leaving 2-4mm seams, if the master leaves the seams unevenly, the tiles will bulge and fall off.

    3. The ratio of cement mortar is wrong, and the ratio of wall tiles is generally 1:, that is, the ratio of a bag of cement, bags of sand, and floor tiles is 1:3.

    4. If the water absorption rate of the tile is greater than 10%, if it is not soaked before paving, the moisture in the cement mortar will be absorbed, resulting in hollowing. The wall tiles are usually made of ceramic bricks, which require a water absorption rate of about 10%, and the floor tiles are usually made of porcelain tiles, which require about a water absorption rate, among which the water absorption rate of porcelain tiles is low, and there is no need to soak in water, and the high water absorption rate must be soaked in water.

    Therefore, this should be done when tiling to avoid hollowing

  7. Anonymous users2024-02-06

    The tile is hollow, generally the cement is not solid, and then it is trampled prematurely. There is no necessary connection with the quality of the tile.

  8. Anonymous users2024-02-05

    As a semi-finished product of decoration, the final effect of ceramic tile has a great relationship with the craftsmanship and proficiency of the paving construction master! Senior paving master told us that there are many situations caused by hollow drums, including no or insufficient joints in the paving, uneven mud and too high cement labeling. Pay attention to these situations when paving, in order to effectively avoid hollowing!

    The flatness of Thompson tiles is leading in the industry, the paving is very simple, and the brick body is ***, as long as the paving method is not wrong, there will be no problem of hollowing off the drum.

  9. Anonymous users2024-02-04

    tile draft, as well as process flow procedures.

  10. Anonymous users2024-02-03

    As we all know, cement mortar is generally used for tiling, but in recent years, there have been more tile adhesives on the market, and I don't know which one is better to use!

    Let's look at the cement mortar first, that is, it is mainly cement, add yellow sand and some waterproof additives, and then stir with water, which is basically zero pollution, high adhesion, and preferential treatment.

    But the bad thing is that cement mortar is affected by many external factors and is easy to fall off. In addition, the hardness of tiles on the market is getting higher and higher, and the focus is on poor water absorption, so the tiles often fall off.

    From the appearance, tile adhesive and cement are almost the same, mainly mixed with water, and then directly used to paste tiles. However, tile adhesive has an advantage that cement does not have, that is, it is less affected by external factors, and it is resistant to low temperature and water. The bad point may be that it is expensive, and there are many bad tile adhesives on the market, and there may even be the problem of excessive formaldehyde.

    Compared with cement and tile adhesive, the adhesive performance of ceramic tile adhesive will be better, the point is that you don't need to run the tile in advance, you can paste it directly. There is no need to paint a thick layer on the wall, and it is basically very firm when pasted on.

    Of course, good things are generally expensive, so there is no need to use tile adhesive in all places, you can use it in the kitchen and bathroom, because these places are often wet, and it is easy to fall off with general cement.

  11. Anonymous users2024-02-02

    Tile without adhesive, or with the use of miscellaneous brands will appear hollow, there will be fall off in the later stage, the first Shanghai Kejian new research and development of nano adhesive brick king quality is very good, green environmental protection, Pacific quality insurance does not empty drum does not fall off, I hope to help you!

  12. Anonymous users2024-02-01

    What kind of tile is used to paste the drum phenomenon, and the tile glue tile tile hollowing phenomenon is more serious.

  13. Anonymous users2024-01-31

    Tile adhesive tile has hollow drum, a big reason is the construction, the plastering should be uniform, and when pasting it, it should be fully kneaded and pressed to flatten the tile, and the correct tile adhesive construction method is:

    Double-sided scraping method of tile adhesive thin sticking:

    1. Apply the glue to the working surface with a toothed scraper to make it evenly distributed and form a toothed shape. About 1 square meter per coating (depending on the temperature);

    2. Knead the tiles on the mortar during the drying time;

    3. The size of the toothed scraper should consider the flatness of the working surface and the concave and convex degree of the back of the tile.

    4. Evenly spread the stirred glue on the back of the tile;

    5. Apply the glue on the working surface with a toothed scraper, then hold the toothed scraper to form a 60° angle between the tooth edge and the base surface, and comb the glue layer into uniform strips;

    6. During the drying time of the glue, the tiles are paved in place, and the brick surface is lightly hit with a rubber hammer;

    7. Slightly rub perpendicular to the carding direction to remove the air in the brick;

    8. In order to ensure the quality of construction, the construction personnel should turn over the pasted bricks from time to time to confirm that the back and base surface of the bricks are completely covered with glue.

  14. Anonymous users2024-01-30

    Summary. Dear Kiss I am happy to answer for you: will the mortar with mortar on the old floor tiles be hollow Answer:

    Kiss will not be the tile adhesive is used to mix in the concrete, used to increase the bond between the tile and the concrete. Tile adhesive is an additive specially used to overcome the hollowing and falling of tiles and concrete. When pasting tiles, you must buy good tile adhesive from big brands, so that the effect will be very good, and there will be no quality problems of hollowing and falling.

    Sticking new tiles directly on the old tiles can save a lot of costs, and it is a good choice for the removal of tiles and garbage transportation costs. Thank you for your patience. The above is my full reply, if you are satisfied with my service, please give a thumbs up, and I wish you all the best!

    Peace and joy! Kiss is happy to answer for you: will the mortar with mortar on the old floor tiles be hollow Answer: Kiss will not be used to mix the tile glue in the concrete, and the punch is used to increase the bond between the tile and the concrete.

    Tile adhesive is an additive specially used to overcome the hollowing and falling of tiles and concrete. When you stare at the tiles, you must buy a good tile adhesive from a big brand, so that the effect will be very good, and there will be no quality problems of hollowing and falling. Sticking new tiles directly on the old tiles can save a lot of costs, and it is a good choice for the removal of tiles and garbage transportation costs.

    Is it made of cement?

    Yes, dear.

  15. Anonymous users2024-01-29

    Dear, hello, I have inquired for you, will the floor tiles be hollow after being paved? There was a problem with the pro-tile adhesive material, which led to a large number of hollow drums. The main thing is that the cement we use is unqualified, and the inspection of the tile hollow drum should be after the tile paving material is solidified. Therefore, I personally think that after the floor tiles at home are laid, it will basically take at least three or four days to be able to check them.

    If the indoor temperature is particularly low, it may take more than a week. Because the purpose of checking the tile hollow drum is to judge whether the tile is effectively combined with the adhesive material. Therefore, it is necessary to ensure that the pasted material is solidified normally and then check it.

Related questions
14 answers2024-07-14

Tile adhesive, also known as tile adhesive or binder, adhesive and other names, is a new type of material for modern decoration, replacing the traditional cement yellow sand, the adhesive force is several times that of cement mortar, can effectively paste large ceramic tiles and stones, and avoid the risk of falling bricks. Good flexibility to prevent hollowing in the production of drums. This product is a polymer modified cement-based tile adhesive, which is divided into No. 1 (ordinary type (reinforced) and No. 3 (larger size tile or marble) and other varieties. >>>More

16 answers2024-07-14

The white floor tiles are shiny and translucent. The light reflective surface is excellent, which will make the light in the living room stronger, and the suitable light is poor, or the living room with a low building, or the owners of the community who like the bright living room. White floor tiles go well with them. >>>More

12 answers2024-07-14

Mix the glue evenly, and do not have corn starch dough.

Method: 1. Mixing of vitrified brick adhesive. >>>More

18 answers2024-07-14

Which is more popular and better-looking, beige tile or gray tile? The answer to this question may surprise many young people, in fact, beige tiles are very popular, and the choice of groups is very wide, as for the kind of better look, it varies from person to person, depending on the matching. So why is beige more popular? >>>More

8 answers2024-07-14

1. Calculate the number of tiles according to the area.

1) First of all, measure the size of the ground wall of the paving space, and calculate the area (length and width). >>>More