Will the floor tiles be hollow if there is no dust around them?

The hollowing of the floor tiles can easily cause the cracking of the floor tiles, which affects the comfort of use, but if the cracking is walked on it with bare feet, it is likely to scratch the soles of the feet, so the installation of floor tiles should be avoided as much as possible. So the question is, if there is no plastering around the floor tiles, will it be hollow? I will share with you this problem today, I hope it will be helpful to you in solving the hollowing of floor tiles.

When the floor tiles are paved, will there be hollowing out if there is no cement grout around them? First of all, this statement should be corrected, when the general master paves the floor tiles, the surrounding area is not not plastered with cement grout, but it will be less than the cement in the middle of the floor tiles, which is a thick inside and thin on the outside. Will this practice lead to hollowing out of the floor tiles?

When the floor tiles are paved, there is only a small amount of cement slurry around it, which is deliberately done by experienced masters, and it will not be hollow.

When decorating friends' homes, you can pay attention to observe that the floor tiles laid by experienced plasterers almost do not need to be cleaned, all are clean, and sometimes a small amount of cement slurry overflows in the seams and is cleaned up. And some not very skilled plastering masters put up the floor tiles, the brick surface is all cement grout, which looks dirty and very uncomfortable.

This phenomenon is actually the difference between whether there is cement slurry around the floor tile paving, and the experienced master will intentionally wipe the cement slurry in the middle of the floor tile a little thicker, and slightly less around, so that through vibration when paving, the cement slurry in the middle will rush to the surroundings, which ensures that the surrounding area can be full of slurry, and there will be no large amount of cement slurry overflowing the surface of the floor tile.

Therefore, when the floor tiles are paved, only a small amount of cement grout around them will not be hollowed, and only those unskilled mud masters may have the phenomenon of hollowing, and only unskilled masters will wipe the cement grout on the back of the floor tiles as much when paving. Therefore, when we lay the floor tiles in the masters, there is no need to worry about this situation, as long as the workers are skilled, they will not be hollow.

Generally, it will not be hollow, unless the cement in the floor tile is uneven, which will cause the phenomenon of hollowing the floor tile.

If the floor tiles are not dusted, it will indeed be hollow, so don't skip this step for the sake of laziness, otherwise the consequences will be a little troublesome.

It's possible that this one will be empty, but no one can guarantee it. It's just a floor tile, and it won't fall or anything, and the empty one is nothing, it's the same as other non-empty ones, it's all good.

If there is no dust around the floor tiles, will it cause hollowing? No, it won'tWill the wall be hollow if there is no putty around the floor tiles? When the floor tiles are paved, if there is no putty around the floor tiles, will the wall be hollow?

In fact, we can't immediately tell if the wall is hollow or not. Because each paving method and the habits of its paving workers are different. However, the opinion I provide is that there is no putty around the floor tiles, and the possibility of hollowing the wall is very large.

This is reflected in the following two situations.

When the floor tile is parquet, the grout is up to standard; The said paving floor tile squeezing standard, that is, there is no putty around the floor tiles, but we have adopted the appropriate way of paving, and the cement mortar rubbed on the back of the floor tiles is squeezed evenly. In these cases, the floor tiles are hardly hollow. Since the cement mortar has been evenly and delicately covered on the back of the floor tiles.

You can take a look at the following operation process to know the big truth.

The back of the floor tiles is rubbed with cement mortar, but the floor tiles that are not coated with cement mortar are parquet on the pavement bond. Use an eraser to wipe runny nose or a special tool for tiling to lay the floor tiles. There is cement mortar all around the floor tiles.

Gently remove the cement mortar around the floor tiles, so that the floor tiles will be paved like that. Therefore, we follow the above process and repeatedly carry out the following floor tiles again.

The floor tile parquet is not squeezed when it is not passed; The floor tile parquet is not squeezed when it is not up to parquet, which means that everyone immediately paves the floor tiles that are not coated with cement mortar on the back of the pavement bond. In the process of laying the floor tiles, there is no cement mortar extrusion around the floor tiles, which indicates that the cement mortar behind the wall tiles is not. The possibility of such a thing happening bulging is very strong.

For details, we can take a look at the operation process.

Everyone is the same, or the floor tiles that are not coated with cement mortar around are spread on the top of the bonding layer. Use an eraser hammer or a tile shaker to lay the tiles in this area. However, during the beating of the eraser hammer, there is no cement mortar around the floor tiles.

In this case, the laying of the next wall tile was carried out. In this order, the floor tiles are laid all the way.

Yes. When pasting in life, you should go to plastering to have a good result, otherwise there may be a hollow state. Choose the right way to pave it.

It should be, sometimes it can cause the cement to be squeezed unevenly, and there will be a hollowing.

It will cause hollowing, it will also cause damage to the floor, and it will lead to poor quality of the floor.

It should not be expensive. Generally speaking, experienced life will be smeared a little thicker in the middle, and then the cement slurry will gush around, so that it can fill the surface of the floor tiles well.

It leads to uneven squeezing of cement and empty barrels.

Summary. Hello, according to your description yes, you need to follow, [Situation 1] The tile is qualified when the tile is paved.

The so-called paving floor tile squeezing is qualified, which means that there is no plastering around the floor tiles, but we have taken the correct paving method to squeeze the cement slurry applied on the back of the tiles evenly. Under these conditions, the tiles are also almost non-hollow. Because the cement slurry has been evenly and fully covered on the back of the tile.

Operation steps: 1. The back of the tile is coated with cement grout, but the tile is not coated with cement grout around it and paved it on the ground bonding layer. Second, use rubber snot or special tiling tools to lay tiles.

Until there is grout on all sides of the tile. 3. Gently remove the cement grout around the tile, then you will finish paving such a tile. So we repeat the above steps and continue to lay the following tiles.

Is it hollow if the ash at the bottom of the floor tile is not connected with the ground?

Hello, according to your description yes, you need to follow, [Situation 1] The tile is qualified when the tile is paved.

The so-called sail stool paving floor tile extrusion qualified, means that there is no plastering around the floor tiles, but we have taken the correct paving method to squeeze the cement slurry on the back of the tiles. Under these conditions, the tiles are also almost non-hollow. Because the cement slurry has been evenly and fully covered on the back of the tile.

Operation steps: 1. Coat the back of the tile with cement grout, but there is no porcelain brick coated with cement slurry around it and pave it on the ground bonding layer. Second, use rubber snot or special tiling tools to pave the porcelain core and bricks.

Until there is grout on all sides of the tile. Third, the cement grout around the tile is gently removed, and then the paving is completed. So we repeat the above steps and continue to lay the following tiles.

The floor tiles that have not been watered will be hollow, and they can be found after the cement is dry. The hollow drum is caused by the presence of air in the original masonry and the powder layer, when detecting, the hollow drum hammer or hard object taps the plastering layer and the leveling layer to make a knocking sound for the hollow drum The "hollow drum" in the quality of the house generally refers to the hollowing phenomenon between the ground, wall, ceiling decoration layer (plastering or pasting surface bricks) and the structural layer (concrete or brick wall) due to pasting and combination, commonly known as "two layers of skin". The reason for the formation is that the plastering of the base layer of the wall is not treated as required or the garbage of the base is not cleaned up.

Before tile paving, check whether the plastering of the wall base meets the requirements, and the wall base debris, dust and must be cleaned; When paving, the back of the tile is covered with cement mixed mortar or 107 cement slurry and taps the porcelain book banquet brick with a hammer handle or soft hammer to make the cement grout crowd the back of the tile, and then press hard to make the tile firmly combined with the wall base. Not soaked in water before paving or not soaked enough. Tiles (especially glazed tiles) should be soaked in water for more than 2 hours before paving, so that the tiles can fully absorb water, and then take out the shade to dry or wipe the clear water.

If the brick is not saturated with water, it will absorb the water in the mortar prematurely, resulting in the mortar shrinkage and hollowing, and it will also affect the strength of the paste. Not full: When the tile is paved, the mortar is not full, or the tile is not gently beaten and squeezed densely. This is a situation where either the state celery silver cut corners or cut corners:

To save cement mortar, or to save time sloppy. There is another situation that mostly occurs when contracting labor and materials, that is, the quality of the tiles is too poor, and the tiles are afraid of breaking when they are tamped. SolutionThe common way to repair the hollow drum is to shovel the sand ash, refill it with quick ash, and re-batch the putty after drying.

However, some hollow drums, due to the location and other reasons, it is difficult to chisel out, such as the hollow drum between the first hidden concrete protective layer and the base layer is more difficult, some more expensive stones, the hollow drum between the ceramic tile and the base layer, and the stone damage economic loss is greater after chiseling. This type of hollowing can be solved by the method of perfusion repair. The AB resin grouting repair of some engineering crack treatment centers can inject high-strength adhesive into the hollow drum, and the empty position can be filled with full adhesion and compression resistance.

This kind of grouting repair hollow drum method is fast, does not damage the base layer, especially in the underground garage, plant and other sites, the construction process does not affect the owner.

1. The wall is uneven and unclean.

Solution: The thin wall base must be leveled, the wall base is uneven, and the uneven undulation will make the contact between the tile and the wall insufficient and cause hollowing. The strength of the base wall is not enough, there is oil stain, and the base wall is loose, which will directly affect the adhesion of the tile adhesive, resulting in hollowing or even falling off.

2. The tile adhesive is mixed with cement mortar.

The various components in the finished adhesive are proportioned, and adding materials at will will change the proportion, destroying the stability of the material, and the tiles will be hollowed out and fall off after use.

Solution: Replace the tile adhesive.

1.Paving problem, the cement mortar below is not paved and paved when the brick is pasted, and the cement oil is not evenly applied to the back of the brick, 2The cement shrinks too much, causing a vacancy below, 3After paving, put a heavy object on it or a person walks on it, 4If there is no seam paving, caused by thermal expansion and contraction of tiles, if it is only a part of the empty Peng, and the non-important position or just walking without heavy objects, you can consider not demolishing, if you step on the tile has a beating situation, you should remove the repaving on the second day of paving, how to do, the worker should have a way, remove the bricks next to it without hurting the worker's technology, it is likely to hurt the bricks next to it if it is not handled well, at this time it is not a good solution, can not be demolished, see what kind of situation you are and then properly handled!

There are many reasons, there is no good solution, depending on the situation, if you can buy bricks of the same color can be smashed and repaved.

There are many reasons for tile hollowing, such as the separation of the tile from the base layer and the incorrect proportion of cement mortar when the tile is glued.