How high are the tiles in the bathroom generally pasted, and what is the height of the wall tiles in

The tiles of the bathroom generally exceed the height of the person is generally about two meters, because if you want to take a bath, there will be water splashed out, if it is less than two meters, it is likely to be spilled, especially when the stone bridge, if there is, the capital is sufficient, it is recommended that the whole wall is all pasted, because this can be moisture-proof, if it is just general, the wall, it is easy to get damp and mildew, so the minimum is, in the height of more than people.

Now the bathroom is covered with bricks, pasted to the need for the ceiling, if the bathroom heater is installed on the relatively low point (2 meters).

In the past, it was about 13, but it is recommended that you now stick the whole wall, which is both beautiful and waterproof.

It turns out that the earliest time the bathroom was generally tiled more than people on the line, now there is no such paste, now the tile is all the bathroom walls are all pasted, and finally the ceiling.

The tiles in the bathroom will be pasted to different heights according to the requirements of each home decoration, and some people will paste the tiles all over the wall.

The tiles in the bathroom are generally attached to the ceiling. Combined with suspended ceilings.

The bathroom tiles are not very bad, and the money is pasted to the top.

Bathroom tiles are generally pasted all over the wall.

It's best to stick it all, the bathroom is damp, it's better to stick it all, take a bath, do anything, and wipe it. It's hygienic and easy to do.

It is recommended that the bathroom tile is covered with a high wall, after all, the bathroom is humid, and the tile can effectively protect the wall.

Generally, it is best to paste the tiles near the washbasin and shower room to a meter height.

The decorative materials of the bathroom wall and floor include glazed tiles, vitrified tiles and mosaics. Now the most commonly used in the family is glazed bricks, and the common specifications are 300 400mm, 300 300mm, and 250 330mm. The specifications of wall tiles are generally determined by the actual size of the space.

The commonly used specifications for the ground are 300 300mm and 330 330mm.

According to the ceiling, it is generally the meter elevation, of course, there is no dead provision, but the position of the bath bomb should not be too high, nor too short, other places can be arbitrary.

Stick the wall tiles above the ceiling.

Generally, if it is 300*450 horizontally, it will be paved with eight pieces.

With the continuous development of science and technology, many tiles now have good waterproof performance, which makes it much easier for us to clean up our homes. Usually ceramic tiles are used in kitchens, bathrooms and balconies and other damp areas, of which the bathroom is the most used area. So, how high is the bathroom tile sticker?

Bathroom tiles are best when attached to the ceiling, and this height needs to be determined according to the ceiling, usually in meters, and there is no standard for how high it is. However, if the tile is attached to the ceiling, it is best to do some waistline treatment in the middle part, so that it looks more beautiful. In addition, the position of the bathroom bomb should not be installed too high, otherwise the heating effect cannot be achieved, but it should not be installed too low, because the light is too strong.

Precautions for tile paving in the bathroom.

1. When paving tiles in the bathroom, it is best to supervise them on site, so that workers will not waste tiles too much. Because some workers have no sense of responsibility, a lot of materials will be wasted during the construction process. Incomplete tiles can be placed on less noticeable locations such as cabinets and sinks.

2. Before paving the sedan car and renting the tiles, the wall should be roughened, and the rougher the better, so as to increase the stressed area of the cement and the wall.

3. When the bathroom is tiled, the workers must be required to do the bricklayer pull line, and the level should be used to assist, do not believe too much in the worker's craftsmanship, and must strictly require the use of tools to control the quality of the tiling.

4. Usually the decoration company will take the ruler to check the quality of the tiles for the owner, it should be noted that the ruler is not standard, it is best to take the level or aluminum alloy as a ruler to inspect.

Article summary: The above is about how high the bathroom tile is suitable and what needs to be paid attention to in the bathroom tile paving, I hope it will be helpful to you. If you want to know more about it, please stay tuned to Qeeka Home.

In people's daily life, the use rate of the bathroom is higher, and it is also the place where the most water is consumed in the whole home, so it is best to choose wall tiles when decorating the wall. Today I will answer for you, and if you want a friend, you may wish to take a look at how to paste the bathroom wall tiles!

First, how high are the bathroom wall tiles generally pasted.

The wall tiles of the bathroom are best pasted to the ceiling, which is the most plastered to all the walls of the bathroom, and some lines can be processed in the middle of the wall, which can enhance people's visual effect. When choosing bathroom tiles, you need to pay special attention to the waterproofing effect.

Second, how to paste the bathroom wall tiles.

1. The most basic treatment.

First of all, the material on the surface of the wall is removed, and if the wall is uneven, it needs to be filled first, and all the putty coating must be removed.

2. Lofting. Before laying wall tiles, it is necessary to find a good vertical line as a reference in advance, and draw control lines around the wall before construction to facilitate the control of dimensions.

3. Tile cleaning.

Before starting to lay wall tiles, the surface of the tiles must be cleaned, such as floating ash on the surface, soil, etc.

4. Wipe the slurry.

The prepared slurry must be evenly applied to the back of the tile to fill the slurry.

5. Paste wall tiles.

Start by laying the tiles flat on the base layer and flattening the tiles with a rubber mace. During the laying of wall tiles, the tiles can be rotated in small quantities so that the slurry can be in perfect contact with the back of the tiles.

6. Caulking. After that, depending on the size of the tile, the gap between the bricks and bricks should ensure that the caulking can be carried out, and the adhesive used in it must have a certain adjustability, so that the size of the slit can be adjusted.

7. After caulking, you only need to use a damp cloth to clean up the excess caulk and keep the surface of the tile clean.

Summary: The above is to share for everyone how high the bathroom wall tiles are generally pasted and how to paste the bathroom wall tiles, I believe that you have a corresponding understanding after reading the above sharing, if you need to learn more about relevant information, please continue to pay attention to Qeeka Home**, will answer for you one by one.

In the bathroom, because the water vapor is relatively heavy, the tile can have a good waterproof effect. It can also make the daily cleaning work easier, but how high is the wall tile in the bathroom and bathroom? Let's talk about how to paste bathroom wall tiles and how high the general bathroom wall tiles are.

It's best to stick all the tiles to the ceiling, that is, the top, and then you can do some line processing in the middle, and some changes are more beautiful. By the way, it is very important to have a waterproof bathroom. In general, the shower area needs to be more than 180 cm.

That is, to the very top. If there is a bathtub, the height next to the bathtub should be 30 cm higher than the bathtub, and the rest of the wall should be 30 cm brighter. The flowers on the wall of the sink and the adjacent wall should also be waterproofed.

1. The most basic treatment: first, the surface needs to remove pollutants, and if the flatness requirements are not met, the pretreated wall must be leveled. Remove the putty coating from all substrates.

3. Before starting the laying operation, the tile surface, such as floating ash and soil, must be cleaned.

4. Wipe the slurry: The prepared slurry must be evenly applied to the back of the tile to fill the slurry.

5. Place the tiles flat on the base layer and flatten the tiles with a rubber hammer. During construction, the tiles can be rotated in small quantities so that the slurry is in perfect contact with the back of the tile.

6. According to the size of the brick, ensure the gap of the corresponding size between the bricks and the bricks for caulking. The adhesive has a certain adjustability, which allows the size of the slit to be adjusted.

7. After caulking, clean the excess caulk with a damp cloth to keep the tile surface clean.

The above is the introduction of how high the wall tiles are pasted and the laying method of the general bathroom. If you want to decorate the bathroom and don't know how to paste the wallpaper, you can refer to it, I believe it will be helpful to people who don't know how high and how to paste the wall tiles in the general bathroom.

If you don't have chaos, you can get it for free

Tiles are very waterproof and easy to clean, so they are often used in the decoration of cooking rooms and bathrooms. So, how high is the bathroom tile? What are the precautions for tiling in the bathroom?

Let's find out with me!

First, how high is the bathroom tile appropriate:

It is best to be able to fully tile the ceiling, and make some waistline in the middle for decoration, which is not only beautiful, but also very exquisite. Here I would like to remind everyone that the waterproofing of the bathroom must be done well, usually the bathing area should be 180 cm, and it can also reach the top; If you want to put a bathtub, then the surface of the wall adjacent to the bathtub should be 30 cm higher than the bathtub, and the rest of the walls should be 30 cm. In addition, if the sink is attached to the wall, it is best to make the adjacent wall waterproof. Second, the bathroom tile precautions:

1. When tiling in the bathroom, everyone must go to the site in person to supervise the work to prevent the construction personnel from wasting too much material. If you are not on site at the time of construction, you will spend a lot of bricks when you encounter some black-hearted plasterers.

It is proposed that individual tiles that are not very good can be pasted by the master to those invisible places, such as the back of the washbasin and cabinets, etc., and pay attention to the tiles, waist bricks, etc. should not be pasted in the above positions by the workers, otherwise you will not see anything in the future, and you will spend money in vain. 2. Try to make the surface of the wall rough before tiling, because this can increase the contact area between the cement and the surface of the wall. The detailed method is to use an electric drill to drill more pits on the wall to resist blindness, the more the better.

3. Usually the main wall is good to use cement mortar, but when the flue of the cooking room, the air duct of the bathroom and the wall with pipes are tiled, 108 glue must be added to the cement mortar to increase the viscosity.

4. In order to avoid the situation of hollowing the drum, we can not immediately check the beating when the tile is pasted, usually wait for an hour or two before knocking, especially pay attention to the four corners of the tile. Here I suggest that you should do a piece of knocking checks, once you find that there is a hollow drum in the place immediately rework, do not be soft-hearted, because if you are about to do it at this time, you will know the harm of hollow drum when you finally install something to punch the hole in the tile, then if you hit the tile and fall off a corner, you will want to cry without tears.

The above is about tile the bathroom.