How does Kesan light operate? How to operate the lights in test subject 3

Updated on Car 2024-07-13
8 answers
  1. Anonymous users2024-02-12

    The lighting operation of subject 3 is as follows:

    1. Driving at night without street lights and poor lighting: wide indicator lights, high beams (another way here is to turn on the headlights, hear the headlights switch to high beams before operating, and the coach and professor shall prevail during the exam). Yes.

    2. Please change the headlights into high beams: keep them still when the high beams are turned on; Switch to high beam with low beam on.

    3. Meet non-motorized vehicles on narrow roads at night: turn on the low beams.

    4. Meeting with a motor vehicle at night: Turn on the low beams.

    5. After sharp bends and slopes at night: the high and low beams flashed twice alternately.

    6. Follow the car in the same direction at night at close range: turn on the low beams.

    7. Overtake the vehicle in front at night: left turn signal, alternating high and low beams.

    8. If there is a fault on the road at night, the traffic is difficult to move: turn off the headlight group, turn on the wide lights and warning lights.

    9. Passing through an intersection without traffic light control at night: the high and low beams flashed twice alternately.

    10. Passing through arched bridges and pedestrian crossings at night: the high and low beams flashed twice alternately.

    11. Driving in foggy weather: turn on the wide lights, front and rear fog seepage lights, and warning lights.

  2. Anonymous users2024-02-11

    The lighting operation of test subject 3 is as follows:

    1. At night, when driving under the jujube shop without poor street lighting, turn on the old lights of Yuangaiyan.

    2. Turn on the low beam at night on the narrow road and non-motorized vehicles.

    3. Low beam with motor vehicle at night.

    4. Follow the car in the same direction at night with low beams.

    5. It will also alternate between high and low beams at intersections without traffic signal control.

    6. At night, through sharp bends and slopes, the high and low beams alternate. Nuclear liters.

    7. At night, the pedestrian crossing through the arch bridge alternates between far and low lights.

    8. Turn on fog lights and hazard warning lights when driving in foggy days.

    9. At night, through the intersection without traffic signal control, the high and low beam lights alternate.

    Summary: There are no lights, turn on the headlights, follow the car, and the car will use low beams to alternate with low and high beams.

  3. Anonymous users2024-02-10

    How to operate the lights in subject 3 is as follows:Voice Commands and Corresponding Operations:

    1. Items with high beams turned on:

    1. Please turn on the high beams.

    2. Driving at night without street lights and poor lighting.

    2. Projects using low beams:

    1. Please turn on the low beam.

    2. Go straight through the intersection at night.

    3. Drive on well-lit roads at night.

    4. Meet non-motorized vehicles at the narrow bridge at night.

    5. At night, let the party drive on the road with street lights.

    6. Meet the motor vehicle at night.

    7. Meet non-motorized vehicles on narrow roads at night.

    8. Follow the car in the same direction at night at close range.

    3. Projects that require alternating high and low beams:

    1. Pass through sharp bends at night.

    2. Pass the slope at night.

    3. Pass the arch bridge at night.

    4. Cross the pedestrian crossing at night.

    5. Pass through an intersection without traffic light control at night.

    6. Overtake the front limb only vehicle at night.

    4. Items that need to be used at the same time as low beam and turn signals:

    1. Turn left at the intersection at night.

    2. Turn right at the intersection at night.

    5. Items that need to be used at the same time as fog lights and hazard warning flashers:

    1. Drive on foggy days.

    Sixth, the need to show the width of the hunger lamp and the double flashing lights at the same time of the project:

    1. Temporary parking on the side of the road.

    2. If a traffic accident (failure) occurs on the road at night, it is difficult to prevent traffic and it is difficult to move, and the headlights need to be turned off.

    The contents of the driver's license test subject 3 are as follows:

    The road test items of Driver's License subject 3 are: Preparation for getting on the bus, starting, driving in a straight line, changing lanes, passing through an intersection, pulling over, passing a pedestrian crossing line, passing a school area, passing a bus stop, meeting a car, overtaking, making a U-turn, and driving at night.

    The travel management department of the provincial-level public security organ may, on the basis of the actual situation of each locality, add the test items of the quasi-driving type of automobiles, and determine the test items of other quasi-driving types.

  4. Anonymous users2024-02-09

    The operation method of subject 3 lighting is as follows:

    1. If you are about to turn at the intersection, please use low beams.

    2. If you are driving on a low-visibility road, please turn on your high beams.

    3. If you are going to pass through a sharp bend, please alternately use the high and low beams and do not close them less than 2 times.

    4. If you are going to pass through the slope, please alternately use the far missing low beam no less than 2 times.

    5. If you are going to pass through the arch bridge, please use the high and low beams for no less than 2 times.

    6. If you are going to cross a pedestrian crossing, please use the high and low beams alternately no less than 2 times.

    7. If you are going to pass through an intersection that is not controlled by traffic lights, please use the high and low beams alternately no less than 2 times.

    8. If you are about to overtake, please turn on the left turn signal first, then alternate the high and low beams no less than 2 times, and then turn on the right turn signal.

    9. If you are going to meet other vehicles, please turn on the low beams.

    10. After the lighting simulation is completed, candidates need to turn off the lights and proceed to the next test.

  5. Anonymous users2024-02-08

    Branch 3 light operation step quietly frank Zen:

    1. Take the test first when you get on the bus, check the instruments and lights; Prepare for the dust removal work and do enough, press the fingerprint to listen to the voice;

    2. Start at the end of the voice, and the operation should be completed in 5 seconds; Test the letter of the Qin test to start the front light to ensure that the low beam is on;

    3. Meet the car, follow the car and go straight, turn on the low beam and don't forget; There is also a new item for turning, and there is no problem with the low beam turned on;

    4. Hear passing and beyond, high and low light flashing alternately; The high beams will only be turned on when the lighting is poor;

    5. When the car breaks down or stops, the width warning is turned on; If the lights are the same, stop the operation and listen to the voice; At the end of the exam, the voice is washed and all the lights are turned off.

  6. Anonymous users2024-02-07

    The operation skills of Kesan lighting include the use of front and rear lights, the use of turn signals, the use of hazard warning flashers, and the use of marker lights.

    1. The use of front and rear lights: When driving at night or in the case of low visibility, the front and rear lights need to be turned on. Headlamps are mainly used to illuminate the road ahead, while rear lights are mainly used to illuminate the situation behind the vehicle.

    When using the front and rear lights, it should be noted that the order of switching the front and rear lights is left and then right, that is, the left light is turned on first, and then the right light is turned on.

    2. The use of the turn code answer light: in the case of turning, changing lanes, overtaking, etc., the turn signal needs to be turned on. The function of the turn signal is to signal to other vehicles that they are driving intentions.

    When using the turn signal, it should be noted that the order of switching the turn signal is left and then right, that is, turn on the left light first, and then turn on the right light.

    3. The use of hazard warning flashing lights: In case of emergency, such as vehicle failure, traffic accidents, etc., it is necessary to turn on the hazard warning flashing lights. The function of hazard warning flashing lights is to alert other vehicles to avoid them.

    When using hazard warning flashers, it is important to note that the hazard warning flashers can only be turned on when the vehicle is stationary.

    4. The use of marker lights: in the case of driving at night or low visibility, it is necessary to turn on the marker lights. The role of the marker light is to signal to other vehicles about the width and length of their body.

    When using marker lights, it should be noted that the order of switching on and off marker lights is left and then right, that is, turn on the left light first, and then turn on the right light.

    Subject 3 precautions include adequate preparation, dress carefully, maintaining a good mental state, and obeying traffic rules

    1. Adequate preparation: Before taking the subject 3 test, you should ensure that you have mastered the basic driving skills and safety knowledge. You can improve your driving skills by attending driving school training, self-study, or consulting with an experienced friend.

    Also, familiarize yourself with the exam process and exam requirements so that you can perform at your best on the exam.

    2. Pay attention to dress: When taking the subject 3 exam, make sure that your dress is in accordance with the regulations. In general, formal attire such as suits, shirts, etc., should be worn. At the same time, it is also necessary to pay attention to the choice of shoe bridge, it is recommended to choose comfortable, non-slip sneakers or leather shoes.

    3. Maintain a good mental state: Before the exam, make sure that you are in a good mental state. Avoid bad habits such as staying up late and overworking to avoid affecting your exam performance. At the same time, you should maintain your self-confidence and believe that you will be able to pass the exam successfully.

    4. Obey the traffic rules: During the test, you must strictly abide by the traffic rules. Pay attention to the road conditions, follow the traffic lights, keep an appropriate distance between vehicles, follow the speed limit, etc. Only by doing this will you be able to ensure that you will perform well in the exam.

  7. Anonymous users2024-02-06

    1. Voice: Driving at night without street lights and poor lighting.

    Correct operation: wide indicator lights, high beams (another way here is to turn on the headlights, hear the headlights switch to high beams before operating, and the coach and professor shall prevail during the exam).

    2. Voice: Please change the headlights to high beams.

    Correct operation: Remain motionless with the high beams on; Switch to high beam with low beam on.

    3. Voice: Meet non-motorized vehicles on narrow roads at night.

    Correct operation: Turn on the low beam.

    4. Voice: meet with a motor vehicle at night.

    Correct operation: Turn on the low beam.

    5. Voice: After sharp bends and slopes at night.

    Correct operation: The high and low beams flash twice alternately.

    6. Voice: driving on foggy days.

    Correct operation: turn on the wide lights, front and rear fog lights, and warning lights.

    7. Voice: After the simulated night test is completed, please turn off all lights.

    Correct operation: Turn off all lights.

  8. Anonymous users2024-02-05

    After the light operation simulation of subject 3 replaced night road driving, although the difficulty of the exam was reduced, many students were still confused about this project.

    It has been observed that there are two main reasons for failing in this project:

    1. I don't know what kind of light should be used in the road conditions reported by the voice;

    Second, know what kind of light to use but don't know how to actually operate.

    The following will teach you how to pass the subject 3 lighting simulation operation exam in turn.

    1. Memorize the following exam steps.

    Required. 1. Driving at night without street lights and poor lighting - (turning on the headlights is also the front flash buried lights).

    2. Please change the headlights to high beams - (high beams).

    Description: Some coaches teach to turn on the headlights + high beam in the first step, and when prompting 2, there is no need to operate.

    Choose one of three options.

    3. Meet non-motorized vehicles on narrow roads and narrow bridges at night - (low beam).

    4. Meet the other party at night and be 150 meters away from the other party's oncoming car - (low beam).

    5. Passing through slopes, arch bridges, pedestrian crossings, and intersections without traffic signal control at night - (alternating flashes from near and far).

    Choose one of the two.

    6. A traffic accident occurs on the road at night, which hinders the traffic and makes it difficult to move - (wide indicator light + double jump light).

    7. Driving in rainy days - (fog lights + double jump lights).

    2. Lighting operation**.

    Remember where and how each light is played below.

    The operation of the fog lamp is: pull it outward 2 times.

    In the picture above, dial up to right steering, and down to turn left.

    In the original state (the light is off), operate the mu cover ant pole to dial the high beam forward, and dial the low beam backward (towards your own direction).

    When the low beam is low, dial it back twice (towards you) to flash far and near.

    The double jump light, also known as the hazard warning light, can be pressed.

Related questions
15 answers2024-07-13

1. If you are about to turn at an intersection, please use the correct lights (alternate high and low beams not less than 2 times) 2. If you are driving on a low visibility road, please use the correct lights (turn on the high beams) 3. If you are going to pass through a sharp bend, please use the correct lights (alternate high and low beams no less than 2 times) 4. If you are going to pass through a slope, please use the correct lights (alternate high and low beams no less than 2 times) 5. If you are going to pass an arch bridge, please use the correct lights (alternate high and low beams no less than 2 times) 6. If you are going to cross a pedestrian crossing, use the correct lights (alternate high and low beams no less than 2 times). >>>More

9 answers2024-07-13

Friends, it is not necessary to have a car in front of you to complete the "overtaking" project in subject 3! When the on-board computer voice report "Please overtake ahead", you first hit the left turn signal, head to the left rearview mirror to observe, if there is no vehicle, 3 seconds before you can change lanes to the left! When you're done changing lanes, turn off your left turn signal! >>>More

9 answers2024-07-13

Operation method: Turn on the right turn signal, observe the rear and right road traffic conditions through the inner and outer rearview mirrors, and look back to observe, after confirming the safety, step on the clutch and brake, and choose the right time to pull over. After parking, the vehicle is controlled within 30cm from the right edge of the road or the edge of the sidewalk. >>>More

16 answers2024-07-13

Kuai3, also known as Xiamen Express 3 Road, Kuai3 Road, Kuai3 Line, full name Xiamen Bus Rapid Transit Line 3, Xiamen Bus Rapid Transit, that is, Xiamen Bus Rapid Transit System (BRT), belongs to Xiamen Bus Rapid Transit Operation. >>>More

8 answers2024-07-13

Subject 3 demerit criteria. The main thing is to park on the side, if the distance is less than 50 deductions, as long as you break the rules is dead. I have to retake the test, and he scored 90 points, which is considered a passing grade.