How many times do I have to play the distance and near lights in the subject 3 exam?

1. If you are about to turn at an intersection, please use the correct lights (alternate high and low beams not less than 2 times) 2. If you are driving on a low visibility road, please use the correct lights (turn on the high beams) 3. If you are going to pass through a sharp bend, please use the correct lights (alternate high and low beams no less than 2 times) 4. If you are going to pass through a slope, please use the correct lights (alternate high and low beams no less than 2 times) 5. If you are going to pass an arch bridge, please use the correct lights (alternate high and low beams no less than 2 times) 6. If you are going to cross a pedestrian crossing, use the correct lights (alternate high and low beams no less than 2 times).

7. If you are going to pass through an intersection that is not controlled by a traffic light, please use the correct lights (alternate high and low beams no less than 2 times).

8. If you are about to overtake, please use the correct lights (turn on the left turn signal first, then alternately use the high and low beams no less than 2 times, and then turn on the right turn signal).

9. If you are going to meet other vehicles, please use the correct lights (turn on the low beams).

Twice. Driving normal use of lights:

If you are about to turn at an intersection, use the correct lights (alternate high and low beams no less than 2 times).

If you are driving on a low-visibility road, use the correct lights (turn on your high beams).

If you are going to pass a sharp bend, use the correct lights (alternate high and low beams no less than 2 times).

If you are going to cross a ramp, use the correct lights (alternate high and low beams no less than 2 times).

If you are going to cross an arch bridge, use the correct lights (alternate high and low beams no less than 2 times).

If you are going to cross a pedestrian crossing, use the correct lights (alternate high and low beams no less than 2 times).

If you are going to pass through an intersection that is not controlled by a traffic light, please use the correct lights (alternate high and low beams no less than 2 times.

If you are about to overtake, use the correct lights (turn on the left turn signal first, then alternate the high and low beams no less than 2 times, and then turn on the right turn signal).

If you are going to meet other vehicles, please use the correct lights (turn on the low beams).

Subject 3 Lighting Exam Far and Near Alternate Lighting Lights need to be pressed twice in total, or more, and the exam lighting only needs to be inducted by the computer.

It doesn't matter if you alternate lights a few more times. The motor vehicle driver's license subject 3 is not a night test, and a simulated light test is required, and 20% of them are generally selected for the night test. There is no need to operate the lights during the exam after the simulated light test.

According to the provisions of the "Rules for the Application and Use of Motor Vehicle Driver's License": Article 26 Subject 3 Road Driving Skills Test includes: large buses, tractors, city buses, medium-sized buses, large trucks, small cars, small automatic vehicles, low-speed trucks and small automatic passenger vehicles for the disabled to prepare for the test, start, straight driving, plus and minus gear operation, etc.

Points to note for the Subject 3 exam:

1. If the candidate's fingerprint verification fails, please get off the bus and re-collect the fingerprint before queuing up again for the test.

2. During the test, if the candidate's score is lower than the passing score, the system will automatically prompt the candidate to pull over, and the system will prompt the next test after the pullover action is completed.

3. After the candidate completes all the required items as required and the driving distance is greater than 3 kilometers, the system will automatically prompt him to pull over. After hearing the sound of pulling over, students should choose a clear kerbstone on the test route and complete the pullover action after confirming safety. After the pullover is completed, the system will announce the test result by voice.

In the light test, alternate between far and near lights, and when you hear voice prompts such as going through a sharp bend, going to pass a slope, going to pass an arch bridge, going to pass a pedestrian crossing, going to pass an intersection without traffic light control, etc., you should alternate between far and near lights - no less than twice, and generally three times is better, I hope it can help you.

When the high and low lights alternate, the low beam is displayed and hits 4 times. On the contrary, if the high beam is displayed, hit 3 times, and the mantra "far three near four".

Module 3: Simulated night lighting exam.

When the voice announces "The exam starts. Please turn on the light", at this time you need to turn on the low beam, no matter which project you operate later, you do not need to turn off the low beam, until the end of the light test, the voice broadcast "please turn off the light", you can turn off the low beam.

The specific methods of the three dozen lights are as follows:

1. Driving at night under the condition of no street lights and poor lighting.

Correct operation: wide indicator lights, high beams (another way here is to turn on the headlights, hear the headlights switch to high beams before operating, and the coach and professor shall prevail during the exam).

2. Please change the headlights to high beams. Correct operation: Remain motionless with the high beams on; Switch to high beam with low beam on.

3. Meet non-motorized vehicles on narrow roads at night. Correct operation: Turn on the low beam.

4. Meet the motor vehicle at night. Correct operation: Turn on the low beam.

5. Passing through sharp bends and slopes at night. Correct operation: The high and low beams flash twice alternately.

6. Follow the car in the same direction at night at close range. Correct operation: Turn on the low beam.

7. Overtake the vehicle in front at night. Correct operation: left turn signal, alternating high and low beams.

8. If there is a failure on the road at night, the traffic is difficult to move. Correct operation: Turn off the headlight group, turn on the enlightenment wide light and warning light.

Needs to be closed. Subject 3 exams.

Subject 3, which includes the road driving skills test and the safe and civilized driving knowledge test, is a motor vehicle driving license.

Part of the assessment is the abbreviation of the road driving skills and safe and civilized driving knowledge test subjects in the motor vehicle driver test. The content of the road driving skills test is different for different types of prospective vehicles.

The content of the road driving skills test in subject 3 generally includes: preparation for getting on the bus, light simulation test, starting, driving in a straight line, adding and decreasing gears, changing lanes, and pulling over.

Go straight through the intersection, turn left at the intersection, turn right at the intersection, cross the pedestrian crossing line, pass the school area, pass the bus stop, meet the bus.

Overtaking, U-turning, driving at night.

Exam difficulty

1. The speed does not match the gear.

Regarding the mistakes of high-end low-speed and high-speed low-gear, you need to pay attention to it during the test drive. In your gear shift.

Be sure to increase or decrease the speed to match the gear before switching gears! Remember to glance at the speedometer every eight seconds while driving to prevent this error from happening.

2. Deviation in the direction of straight driving.

During driving, many students deliberately slow down the car because they are worried that the driving trajectory is not in a straight line, which is not advisable. This will increase the possibility of the vehicle's trajectory shifting, so you should keep a reasonable speed and drive at a constant speed.

If you don't turn off the high beam, the system will not know that you have carried out the marker light operation, and it may be counted as no operation and deduct points.

Just turn off the lights.

1. When the examiner gives the command of "please turn on the marker light", the student adjusts the light control knob (or button) to the "marker light" opening gear.

2. When the examiner gives the command "Please turn on the high beam", the student will adjust the light control knob (or button) to the "low beam" opening gear while keeping the marker light on.

3. When the examiner gives the instruction of "please alternate the high and low beams", the student will turn the turn signal lever to the direction of the student for 3 consecutive times while keeping the "marker lights and low beams" on, and at the same time observe whether there is any change in the far and low beams in front of the engine compartment of the vehicle.

4. When the examiner issues the command "Please switch from low beam to high beam", the student will adjust the light lever to the "high beam" opening gear while keeping the "marker light and low beam" on, and observe whether the "high beam opening sign" on the dashboard is on.

5. When the examiner gives the command "Please switch from high beam to low beam", the student will adjust the light lever to the "low beam" opening gear while keeping the "marker light and low beam" on, and observe whether the "high beam on the open sign" on the instrument panel is off.

6. When the examiner gives the command of "please turn on the anti-fog lamp", the student will adjust the light control knob (or button) to the "anti-fog lamp" opening gear while keeping the "marker light and low beam light" on.

7. When the examiner gives the command "Please turn off all lights", the trainee will adjust the light control knob (or button) to the light off gear.

The high beam must be turned off before you can switch to double flashing and reveal the profile light. Indicator Width Lamp...

Summary. Hello: If you need to turn off the high beams and then turn on the marker lights and double flashes, be sure to turn off the high beams and the silver light!

Then turn on the marker light and double flash, because after the high beam is turned on, the marker light has touched the stove and is not in the same position, and you need to turn off the high beam before you can turn on the marker light and smile double flash!

For example, if you turn on the high beam, do you need to turn off the high beam to turn on the low beam, the reason is the same! So you have to turn off the high beams and start the marker lights! The following is the ** of the subject three missing rolling light exam!

Specifically, I hope it can help you!

After the end of the test simulation light in subject 3, you don't need to turn off the high beam and then turn off the low beam, just turn off the light.

Subject 3: Lighting Mock Exam Items:

1. Turn at the intersection at night and use low beams.

2. When driving on low-visibility roads at night, turn on the high beams.

3. At night, it is necessary to pass through sharp bends and alternately use high and low beams no less than 2 times.

The test mileage of large buses and medium-sized buses shall not be less than 20 kilometers, of which the test mileage shall not be less than 10 kilometers during the day and shall not be less than 5 kilometers at night. The test mileage of tractors, city buses and large trucks shall not be less than 10 km, of which the test mileage shall not be less than 5 km during the day and shall not be less than 3 km at night.

The test mileage of small cars, small automatic transmission vehicles, low-speed trucks, and small automatic transmission passenger vehicles for the disabled shall not be less than 3 kilometers, and no less than 20% will be selected for night testing; If the night test is not conducted, the test shall be conducted to simulate the use of night lights.

Road Driving Skills:

The content of the road driving skills test in subject 3 includes: large buses, tractors, city buses, medium-sized buses, large trucks, small cars, small automatic transmission vehicles, low-speed trucks and small automatic transmission passenger vehicles for the disabled, preparation for the test on the bus, simulated night light test, starting, driving in a straight line, and operation of adding and decreasing gears.

Changing lanes, pulling over, going straight through an intersection, turning left at an intersection, turning right at an intersection, crossing a pedestrian crossing line, passing a school area, passing a bus stop, meeting a car, overtaking, making a U-turn, driving at night; The content of other quasi-driving tests shall be determined by the traffic management department of the provincial-level public security organ.

If you need to turn off the high beams and turn on the marker lights and double flashes, be sure to turn off the high beams! Then turn on the marker light and double flash, because after the high beam is turned on, the marker light is no longer in the same position, and the high beam needs to be turned off before the marker light and double flash!

Subject 3, including the road driving skills test and the safe and civilized driving knowledge test, is a part of the motor vehicle driving license assessment, and is the abbreviation of the road driving skills and safe and civilized driving knowledge test subjects in the motor vehicle driver test.

The content of the road driving skills test in subject 3 generally includes: preparation for getting on the bus, light simulation test, starting, driving in a straight line, adding and decreasing gear operations, changing lanes, pulling over, going straight through the intersection, turning left at the intersection, turning right at the intersection, passing the pedestrian crossing line, passing the school area, passing the bus stop, meeting the car, overtaking, making a U-turn, and driving at night.

The content of the safe and civilized driving knowledge test generally includes: safe and civilized driving operation requirements, safe driving knowledge under bad weather and complex road conditions, emergency handling methods such as tire bursts, and disposal knowledge after traffic accidents.

Starting from 1 June 2021, the interval between the subject 3 examinations will be adjusted from 30 days to 20 days after passing the subject 1 examination. For those who increase the driver's license of large and medium-sized passenger trucks, the interval between subjects three and the test will be adjusted from 40 days to 30 days after passing the subject 1 test.

Driver's License:

The driver's license test is divided into 4 subjects, and you can get a driver's license if you meet the requirements of each subject.

The above content is reference: Encyclopedia - Subject 3 1

Follow the voice operation, if there is no requirement to turn off, you do not need to turn off the high beam until the process is complete. Turning on the double flash is usually the last step, so you need to turn off all the lights for five seconds after turning it on, and start to start the road test. So the high beam does not need to be turned off.

Of course, you need a password and a light, except that the low beam switches to the high beam, otherwise only the low beam remains the same.