Want to paint latex, how many times do you have to apply paint?

Updated on home 2024-07-16
7 answers
  1. Anonymous users2024-02-12

    Two or three times, so that the color is more even, and there will be no particularly serious taste, generally the first time is the base, the second time is covering, and the third time can achieve the effect of wall smoothing.

  2. Anonymous users2024-02-11

    At least three times should be applied, generally 1 time of primer, 2nd time of topcoat, 3rd time of latex paint. If you can do this consistently, the end result will be perfect.

  3. Anonymous users2024-02-10

    In general, it needs to be applied two to three times. In this way, you can get a good glossy feel and look very good.

  4. Anonymous users2024-02-09

    Generally, wall latex paint needs to be brushed three times.

    Brush the first latex paint: the painting sequence is to brush the top plate first and then the wall, and the wall is up and then down. Clean the wall first, and use a cloth to wipe off the dust on the wall.

    The latex paint is painted with a pen, and when you use a new pen, remove the floating hairs and unstable hairs on the pen. Latex paint should be stirred evenly before use, and diluted with water appropriately to prevent the paint from not opening all over the head. After drying, the putty is replenished, and then dried and polished with sandpaper and cleaned;

    Brush the second time latex paint: the operation requirements are the same as the first time, fully stir before use, if it is not very thick, it is not appropriate to add water to prevent penetration. After the paint film is dried, use fine sandpaper to polish off the small bumps on the wall and the brush bristles, and clean them after grinding them smooth;

    Brush the third latex paint: the method is the same as the second latex paint. Because the latex paint film dries quickly, it should be operated continuously and quickly, starting from one end and gradually brushing to the other end, and the upper and lower brushes should be connected to each other to avoid the joint after drying.

  5. Anonymous users2024-02-08

    Summary. Hello dear. 3 times.

    Generally, it is 1 primer and 2 topcoats, but in actual construction, most of them omit the primer construction, and simply spray 2 to 3 times of latex paint topcoat. Note that it is best not to paint the interior wall latex paint more than 4 times, for fear that the paint film is too thick, the humidity of the room is too low, resulting in the cracking of the paint film, the latex paint should be stirred evenly before use, and diluted with water to prevent the paint brush from opening all over the head.

    Brush latex paint normally and brush it several times well.

    Hello dear. 3 times. Generally, it is 1 primer and 2 topcoats, but in actual construction, most of them omit the primer construction, and simply spray 2 to 3 times of latex paint topcoat.

    Note that it is best not to paint the interior wall latex paint more than 4 times, for fear that the paint film is too thick, the humidity of the room is too low, resulting in the cracking of the paint film, the latex paint should be stirred evenly before use, and diluted with water to prevent the paint brush from opening all over the head.

    Precautions for brushing latex paint 1, the consistency of the paint (latex paint) with obvious whiskering should be moderate, and the amount of paint dipped in the pen should be appropriate, and the brushing should be more smooth and smooth, so as to prevent the whiskering from being too large. 2. The reason for the bottom is that the paint film is thin, so in addition to paying attention not to miss the brush, the consistency of the latex paint should also be maintained, and too much water should not be added. 3. When the brush is obviously painted, it should be brushed up and down, and the next row of pens is followed by the previous row of pens, if the interval is slightly longer, it is easy to see the obvious joints, so when painting in a large area, it should be equipped with sufficient personnel and connect with each other.

    4. Before the construction of the uneven color separation line, the powder line should be carefully drawn, and the color separation line should be relied on by putting a ruler, the force should be even, the rise and fall should be light, and the amount of dipping pen should be appropriate, brushing from left to right. When painting the paint with color, the ingredients should be appropriate, ensure that the same batch of paint is used for each time on the independent surface, and it is advisable to use it once to ensure that the color is consistent. 5. When the paint just produces the fall, you can immediately use the paint brush to gently brush the traces of the flow, if it is a viscous coating, you can use a clean paint brush dipped in turpentine to brush the falling part again, so that the flow part is dissolved again, and then use the paint brush to push the flow drop away and flatten.

    If the paint film has dried, for slight sinks, you can use fine sandpaper to smooth the sink, and for large areas of sinks, you can use water sandpaper to sand, and then apply it again after repairing the putty. 6. When the paint film has particles and the surface is rough, you can use fine sandpaper dipped in warm soapy water to carefully flatten, grind, wipe dry, wipe off the dust, and then repaint. If it is a high-grade finish, you can use water sandpaper to polish and smooth the surface with wax to make the surface bright, so as to avoid the rough surface of the paint film.

  6. Anonymous users2024-02-07

    <> "No, if you brush it only once, it will affect the use time of the paint, and it may also cause peeling and peeling. In general, we apply primer once, topcoat twice, and after each layer of paint is dry, we need to sandpaper it. In addition, the brushing of latex paint can only be brushed more, try not to brush less in order to save money and crack it, although on the surface, only one brush of topcoat can shorten the decoration period.

    However, the painting results are not very good, which means that they will need to be repainted later, and the budget is often higher than before.

    What do you need to pay attention to in the construction of latex paint.

    1. The wall must be dry. The new house needs to be naturally dried for more than 10 days after treatment, while the concrete wall needs to be naturally dried for more than 20 days, and the moisture content of the wall is lower. Paint should be stored in a cool, dry place above 0.

    2. Refer to the relevant product manuals as much as possible for adding water. Too much water will reduce the gloss, film-forming and durability of the paint. The construction must be stopped if the temperature is lower than 5, the construction must be stopped if the air humidity is too high (higher than 85%), and the construction is strictly prohibited below 0.

    3. The construction of the exterior wall should be stopped in rainy days. If it rains within 12 hours after the end of construction, it can be blocked to prevent rainwater from washing the cladding.

    4. 107 glue is needed for fan ash. It is very likely that the wall will be powdered and moldy quickly, and the paint will peel off, so it is best to add some preservatives. Fan ash topcoat can only be applied after the fan ash surface has dried.

    5. Unused paint should be sealed to prevent drying and waste, and workers should rinse it with water immediately after discharge.

  7. Anonymous users2024-02-06

    1. The joints of all different base layers, the plugging parts behind doors and windows, and the joints of the water and electricity tank must be pasted with white latex before scraping putty to prevent cracks on the wall of the part;

    2. Before plastering, the aerated concrete masonry should be hung with steel plate mesh on both sides, and the wall should be moistened with watering to prevent cracks in the plastering surface layer;

    3. Because the balcony vertical plate is a 50 mm thick C20 fine stone concrete cast-in-place slab, this work is prioritized during the construction of the secondary structure, so that the cracks that may occur are stabilized first and as soon as possible.

    4. Use high-quality water-resistant putty when decorating the wall to avoid cracking on the surface of the decorative layer. Through the above measures, the cracking of the wall surface has been controlled. Similar treatment method, the joint between the wooden frame of the wall cabinet and the concrete riser is inlaid with a wooden face, and the joint between the lower edge of the wooden curtain box and the aluminum alloy edge keel is inlaid with a wooden strip to cover up the cracks that may occur due to different materials, and the effect is good.

    The hinges, handles and other hardware accessories used in the installation of wooden doors and wall cabinet doors are made of high-quality materials to ensure the quality of the project.

Related questions
15 answers2024-07-16

general wall coveringLatex paintIt needs to be brushed three times. It takes 2 days. >>>More

11 answers2024-07-16

Latex paint is generally brushed 2-3 times in accordance with the requirements of the construction process. >>>More

13 answers2024-07-16

Latex paint contains a certain amount of formaldehyde, if there are children at home, it is better to try to move in after three months. However, the exact length of time to check in depends on the actual situation. >>>More

12 answers2024-07-16

Exterior wall paint is not only colorful, but also its water resistance, pollution resistance and weather resistance are also very good, so now it is more and more liked by the majority of consumers. The construction process mainly includes the following processes: 1. Inspection and recording of the wall substrate; 2. Clean the wall foundation; 3. Deal with wall holes, cracks, etc.; 4. Scrape 1-2 layers of putty on the exterior wall according to the situation; 5. Roller coating alkali-resistant sealing primer; 6. Roller coating varnish; 7. Polishing corners and rough parts; 8. Spraying exterior wall paint; 9. Paste tape into grids at the elastic line part; 10. Elastic wire according to size requirements.

8 answers2024-07-16

The specific steps are as follows:

1. Carefully check the surface of the wall to see if there are stains, if there are any, wipe them with a mild cleaning agent, and try to remove the stains; If there is a situation where the old paint film is loose and falling, it is necessary to completely remove the old paint film with a paint shovel. >>>More