The floor heating water separator is the control center of the entire indoor geothermal heating, can

1.The underfloor water separator is the control center of the entire indoor geothermal heating. If the geothermal exhaust valve is broken, it can be replaced.

Otherwise, there will be no exhaust for heating in winter, and the temperature will not rise. When using underfloor heating, it is necessary to deflate on time. The floor heating exhaust valve must be installed in the correct position and vertically.

The installation is straight and without damage, so as to ensure the normal operation and use of the exhaust valve. The exhaust valve on the geothermal water separator can be replaced. The floor heating water separator is the control center of the whole indoor geothermal heating, which has the function of shunting and dividing pressure.

2.When the heat medium flows into the room, it enters the main rod of the separator through the multi-function filter. In this process, the filter filters out impurities from the heat medium to prevent them from entering the underground pipe network and clogging the pipes.

The underfloor heating separator is a diagram of the exhaust valve of the underfloor heating separator, and the underfloor heating separator is the control center of the entire indoor geothermal heating. Knowing that it has a splitter and partial pressure function, when the heat medium flows into the room, it enters the main rod of the water separator through the multi-function filter. How does the filter filter filter out impurities in the heat medium in this link to prevent impurities from entering the underground pipe network and blocking the pipeline.

Can the floor heating water separator be replaced if the floor heating exhaust valve is broken? If you don't understand these aspects, then a lot of problems arise when you reuse them. Can I replace the hot water separator with a new base if the hot manual exhaust valve is broken?

So it is recommended that if the hot manual exhaust valve is broken, look at the hot water separator in the new base first. The main rod is installed horizontally, and the principle of equal height and equal pressure is used to evenly distribute the heat medium.

to the branch tube. After passing through the heat exchange system, each branch pipe flows back to the main pole to collect water, and then flows into the heating system from the return port.

4.In addition, a water mixing device is added to the self-heating system, that is, after heat exchange, the temperature of the heat medium (water) is still very high, and after passing through the water mixing system, it flows into the main trunk of the water separator to continue circulation, so that it can save energy while heating. If you are not at home for a long time, you can use the main valve of the water separator to reduce the circulating water, and do not turn it all off.

If there is no heating in the room all winter, blow the water out of the pipes. Now not only every household in the north will install floor heating, but also in the south to install floor heating. A very important part of floor heating is the water distributor, which is the main part of floor heating.

1.The exhaust valve on the geothermal water separator can be replaced. The underfloor heating water separator is the control center of the entire indoor geothermal heating.

2.It has the function of splitting flow and pressure, when the heat medium flows into the room, it enters the main bar of the water separator after passing through the multi-function filter.

3.The filter filters out the impurities in the heat medium to prevent the impurities from entering the underground pipe network and blocking the pipeline, which has an important filtration effect.

If you can change it, if you don't change it, it is likely to cause problems with heating in winter, you must seek the help of professional and technical workers, use professional tools, and when they replace the geothermal exhaust valve, the general speed is relatively fast, but you must choose a better quality, you must ask clearly, do not operate it yourself.

It can be replaced, because it has the function of diversion and pressure distribution, which can filter out impurities in the hot coal and prevent impurities from entering the underground pipe network to block the pipeline, which will cause greater damage if not replaced in time.

Summary. 2. Then release the gas in the return pipe, close the main valve, and rotate it 90 degrees normally.

There is no small valve in the return branch pipe on the floor heating water divider, and there is no valve in the main return pipe, how to exhaust?

It comes with a lot of circulating pipelines, as long as the exhaust holes of all pipelines are opened, then the floor heating can be exhausted, but if the floor heating is not equipped with a water separator, it can only be exhausted in the pipe well.

1. First connect the heating water pipe with the air release valve, the connection must be careful, and someone should accompany you to check when deflating, because when the floor heating is deflated, its hose may fluctuate due to air pressure, if there is no good supervision, then the hose will fall off, in addition, you must prepare a towel, wrap it around the valve and then open the valve through tweezers, and do not be too heavy when opening, otherwise the water will flow in front of youzai.

2. Then release the gas in the return pipe, close the main valve, and rotate it 90 degrees in the normal dry hole.

3. Then the deflation of the single water pipe, first close the main return valve, and then close the inlet and return valves of the geothermal pipe one by one, and then open the return pipe of the water separator until the water flows out, and then close the valve.

The floor heating inlet valve and return valve must be opened, if it is not opened, it will not be able to circulate, and the floor heating will not be hot; Hot water is poured into the inlet and flows out of the outlet. In the early stage of heating, a large amount of air in the process of water supply also enters the heating pipe at the same time, if it cannot be discharged in time and accumulates in the pipe, it will also cause the heating to be not hot. Generally, manufacturers will give users tips when setting up water inlet pipes and outlet pipes, the valve switch of red material is the switch of the water inlet pipe, and the blue switch is the switch of the return pipe, which can be judged by touching the heat of the two water pipes, and the hotter one is the water inlet pipe, then take the other is the return pipe, because the hot water is from the water inlet pipe into the floor heating coil, and after circulating the ground, it will enter the wall-hung furnace through the water pipe to reheat, and the temperature of the water return pipe will be lower than that of the water inlet pipe after a period of water circulation.

Underfloor heating water separator.

The control opening method of the return valve on the water supply valve is: the supply and return valve can be opened in the counterclockwise direction, and the control can be carried out when it is closed in the opposite direction.

If the return valve is closed, it will affect the temperature of the return water, and it will also reduce the heating temperature, so you can lower the temperature and do not need to close it. Usually water supply and return pipes.

The valve should be opened, and do not move after debugging, otherwise it is not conducive to the temperature balance of the room, and the release valve of the water separator and water collector should be closed, and the air should be unscrewed when the local heating is not hot.

The process of intersecting the single-tube series and the three-way loop through the radiator. The purpose of this is to prevent one radiator from stopping to heat up and affecting other areas. In general, when radiators.

When this part of the room fails, the valve of the middle riser should be opened, and the water supply valve and return valve should be closed.

The geothermal exhaust valve can be replaced if it is broken. Buy a new one and reinstall it, it's also very convenient and fast.

Of course, it can be replaced, but if the damage is severe, then only the pipe assembly can be replaced.

Of course, you can change it, if you want to change, be sure to find a professional master to help you change.

If it can be replaced, it is enough to find relevant personnel to replace it.

Summary. Hello, one of the geothermal water separator ball valves is broken, it can be replaced separately, and the main needs to replace the broken water separator ball valves.

A water separator has an outlet and two or more water outlets, which can be used at the same time or separately, and there are valve devices on the water outlets, which can be opened and closed at any time to control the water flow and facilitate the replacement of branch line accessories.

The water separator is a water distribution and collection device used to connect the water supply and return of various heating pipes in the water system, and its functions are mainly four items: pressurization, pressure reduction, pressure stabilization and diversion.

It is generally pure copper and resistant to decay; Also available in stainless steel; But never cast iron.

If one of the ball valves of the geothermal water separator is broken, can it be replaced separately or all of them should be removed.

Hello, one of the geothermal water separator ball valves is broken, it can be replaced separately, and the main needs to replace the broken water separator ball valves. A water separator has an outlet and two or more outlets, which can be used at the same time or separately, and there are valve devices on the outlets, which can be opened and closed at any time, controlling the water flow and serving the sparrows, and making it easy to exchange branch accessories. The old water separator is a water system, used to connect the heating pipe supply, water return distribution, water collection device, its main function is pressurization, pressure reduction, pressure stabilization, diversion four items.

It is generally pure copper and resistant to decay; Also available in stainless steel; But never cast iron.

During the heating period, the inlet valve and outlet valve of the floor heating separator need to be opened. Probably you need to get the gas out of the pipes.

Reason: The return water is high to better drain the air in the pipe. The switch is installed on the return pipeline, which is very professional construction, and most of the floor heating installations are wrong.

Solution: If there is gas in the floor heating return pipe, you only need to unscrew the return pipe interface to drain the gas, if there is still gas, take a gas cylinder from the water inlet to the water outlet of the return pipe to pump air can be removed.

The geothermal water separator is not hot at the top and not at the bottom.

There is no small valve in the return branch pipe on the floor heating water distributor, and there is no valve in the main return pipe, which means that the exhaust is discharged with the floor heating water. When the heat medium flows into the room, it enters the main bar of the water separator after the multi-function filter, and the filter filters out the impurities in the heat medium to prevent the impurities from entering the underground pipe network to block the pipeline.

The main bar is installed horizontally, so that the heat medium is evenly distributed to the branch pipes by using the principle of equal pressure at the same height, and after the heat exchange system, each branch pipeline flows back to the main bar for water collection, and then flows into the heating system from the return port. In addition, there is a water mixing device in the self-heating, that is to say, after the heat exchange, the temperature of the heat medium (water) is still very high, and after the water mixing system, it flows into the main bar of the water separator to continue circulation, so that energy can be saved while heating.

Normally, a small exhaust valve will be installed on the floor heating pipe manifold.

If there is indeed no exhaust valve on the manifold, it can be exhausted through the exhaust valve on the main heat source or on the buffer hot water storage tank.

For example, if you use an air energy heat pump, a gas wall-hung boiler or other host equipment for heating, there are also designed exhaust valves on the main engine water pipeline.

If there is no exhaust valve on the entire pipeline, an additional manual exhaust valve must be installed, otherwise there will be big problems.

You can open the drain valve to drain the air until the hot water comes out and then close it, which is the fastest.

There are two small connectors on the water separator, which are specially designed to degas or drain water!

**The one in the upper left corner of the manifold can be used, and it seems to be able to be vented.

Send a picture to see! At the water separator!