How to use wall reinforcement? What is the difference between wall reinforcement and wall reinforcem

You can use Keshun home waterproof G100 wall and floor reinforcing agent, use it out of the barrel, buy gloves, rollers, and roll coating on the base surface, and you can lay bricks for waterproofing after drying. The reinforcing agent effectively enhances the strength of the base surface, so that the base surface is not easy to fall off powder and is not easy to crack.

1. The first step needs to clean the wall base, it is best to polish and polish it flat, and there can be no unevenness, keep the wall flat and dry, and then carry out the next step of construction. 2. The second step is to paint the wall reinforcement on the wall, and you can use the brush to match the construction when painting, it is best to apply it twice, and you need to apply it evenly. After the first construction is completed, wait until it is completely dry before brushing the second time, and when the painting is finished, you can scrape putty on the wall.

Second, the process of wall construction, after the construction of the wall reinforcing agent in accordance with the above steps, you can also scrape putty on the wall. 1. When scraping putty, you also need to scrape two to three times, and each putty needs to be even, after the first putty is scraped, wait until it is completely dry and then scrape the second time. 2. After scraping the putty, you can apply primer to the wall, and after the primer is finished, you need to apply the topcoat on the wall.

The whole construction process is relatively simple, and you can operate it in the above way. 3. Precautions for wall construction 1. Before construction, the wall needs to be treated. And when scraping putty, you can't just scrape the putty once, you need to scrape the putty three times, so as to ensure the construction effect later.

2. At the same time, when choosing wall decoration materials, try to choose materials with better quality, so that after the construction is completed, it is not easy to crack or peel the wall, and the wall needs to do the corresponding measures for waterproofing.

What is the difference between wall reinforcement and wall reinforcement The effect of wall reinforcement and wall reinforcement is almost the same, the biggest difference between interface agent and wall reinforcement is the color, the interface agent is white latex, and the wall is yellow latex. The main advantage of using wall solid in decoration is that the wall surface after the wall solid is painted, which can clearly find whether the wall is missing or less painted, so as to prevent the decoration quality from being affected because of missing coating. The interface agent and the wall solid have the same role in the decoration process, mainly used for the interface treatment of the wall base and the cement wool treatment of the base layer, and the main raw materials for its production are the same.

Summary. Hello, glad to answer for you. The difference is that their colors are different, the interface agent is white, and the wall solid is a yellow latex.

1.Wall solid is also a kind of interface agent, can make the wall be consolidated, smeared on the wall will also form a layer of protective film, can effectively prevent stains from adhering to the wall, suitable for wall cloth or wallpaper, interface agent is a kind of adhesive, good environmental performance, without any peculiar smell, does not contain formaldehyde, can prevent the plastering layer from empty shell or shell phenomenon, wall solid practicability is a little higher than the interface agent.

Is wall reinforcement the same as interface agent?

Hello, glad to answer for you. The difference is that their colors are different, the interface agent is white, and the wall solid is a yellow latex. 1.

Wall solid is also a kind of interface agent, can make the wall be consolidated, smeared on the wall will also form a layer of protective film, can effectively prevent stains from adhering to the wall, suitable for wall cloth or wallpaper, interface agent is a kind of adhesive, good environmental performance, without any peculiar smell, does not contain formaldehyde, can prevent the plastering layer from empty shell or shell phenomenon, wall solid practicability is a little higher than the interface agent.

2.Wall solids and interface agents are both good wall decoration materials, and there is still a big difference between the two in terms of decoration effect and performance. Wall solidification is a good wall curing adhesive, with good permeability, can fully penetrate into the surface of the wall base material, can well improve the adhesion between the cement slurry and the wall surface.

The interface agent is mainly used to treat the surface of the object through adsorption or coating, which can improve the surface layer of the wall and have high environmental performance.

Wall solid and interface agent are the interface treatment materials that replace the traditional building glue, their raw materials are basically the same, their functions are basically the same, are used to deal with the wall base interface and smooth base cement, green and environmentally friendly materials to ensure the safety of use, will not cause harm to the human body, and the performance is very good. The only difference between the two is that the interface agent is a milky white liquid, and the wall fix is a yellow liquid.

Do you have any other questions? We'll be happy to continue to answer your questions

I hope the above is helpful to you If you are satisfied with me, please give me a thumbs up

1.The cement mortar can be made more cohesive by wall reinforcement, and if the waterproof paint is used to dry, the entire wall will become seamless, and if the paint is torn, it will fall off the base layer. 2.

If the interface agent is used as a glue, it can not be brushed too thick, too thick will form a film, and it will also peel, you can operate according to the instructions, brush once or twice is just right, so that it can penetrate into the base layer for reinforcement and play a certain water absorption. 3.The main function of the interface agent is to use it in the base layer of glue, as well as in waterproof construction after brushing, and sometimes it can also be used as a wallpaper base film.

1. If there is wall adhesive glue on the furniture, you can use plastic tape to quickly remove the wall adhesive that sticks to the furniture, and use it several times to clean up the wall adhesive that remains on the furniture. 2. Alcohol can also remove the wall solid glue on the furniture, just drop a few drops on it, and then wipe it with a clean rubber cloth, which can quickly remove the wall solid glue on the furniture. 3. You can use liquor to clear the wall solid glue on the furniture, so the liquor has alcohol, stick a little liquor with a rag, and then gently wipe it in the place where the wall solid glue is sticked, the effect is very good.

The wall reinforcing agent is the wall interface agent, and the use method is as follows:

1. Roller painting or mechanical spraying can be used to spray on the surface of the base layer or insulation board to be treated.

2. Mix and stir evenly according to the ratio of cement sand: interface agent = 1 2, and finally directly coat and throw it on the surface of the base layer to be treated.

The "Nippon Paint Wall Reinforcement" you are talking about should be Nippon Paint Wall Solid, and its construction method is to add an appropriate amount of water to dilute it with a roller brush according to the instructions for use.

3. Pay attention to misunderstandings: the color of high-quality wall solid must be milky white and transparent. However, the transparent wall solid is not easy to distinguish after drying, and the process quality cannot be checked.

The color is to facilitate the detection of whether there is a missing brush, missing coating, etc. For this reason, it makes no sense to blindly pay attention to the visual sense of the solid color of the wall. Secondly, the thicker the wall, the better.

The permeability and adhesion of the coating itself are the primary assessment indicators. The excessively thick wall should be diluted with water according to the instructions, otherwise it will increase the difficulty of construction, which will make it difficult to achieve uniformity in the painting process, which will not only affect its permeability, but also be unfavorable to the sealing of the base layer.

Wall reinforcing agent is a kind of wall interface agent, also known as wall solid, the purpose is to increase the adhesion between putty and the original wall, to prevent wall cracking, hollowing, is made of nano-scale polymer polymer emulsion as the base material combined with environmental protection additives. Wall reinforcing agent is a new generation of wall sealing treatment products, with super physical permeability performance, can penetrate deep into the wall, the product has excellent bonding strength, crack resistance and good alkali resistance, moisture-proof, mildew-proof performance after curing, can make the surface layer of the cement wall or plastering wall and the internal fine loose place bonded, so as to improve the overall strength of the wall, effectively improve the wall putty plastering, tile paste base bonding strength and adhesion.

The wall reinforcing agent can avoid hollowing when the plastering mortar is bonded with the base layer, and is suitable for the interface treatment of interior and exterior wall scraping putty and concrete base plastering, so as to increase the adhesion of cement mortar to the base layer. To put it simply, increase the fastness to the plaster or putty that needs to be leveled in the later stage, so that the wall painting is more uniform and durable.

Before the construction of the wall, the surface of the base should be solid, smooth and without obvious cracks; Clean and free of oil stains, no hollowing and falling powder. Before construction, use a shovel to clean the wall and remove loose cement particles to ensure smooth application and full coverage of the reinforcing agent.

After painting, wait about 30 minutes and press the wall with the palm of your hand to see if there is any sticking hand. If not, it proves that the reinforcement treatment of the wall base layer is completed, so that the putty can be scraped on the wall in batches after treatment, which can make the wall more solid and the putty scraping effect better.

For the renovation of the old wall, how to remove the putty of the old wall is a big problem, the old wall shovel is not clean, it will affect the adhesion of the new putty on the wall, and it is easy to lead to the fall of the new putty, so the reinforcing agent is needed to treat the surface of the old wall first. As shown in the figure below, the base of the old wall has not been cleaned, and the skin will still fall off and fall off on the wall.

If you use a reinforcing agent for the wall, it plays a very important role. What are the ways to use wall reinforcements? PChouse will take you to find out.

1. Grassroots cleaning: ensure that the wall is clean, dry and flat, ensure that the surface humidity of the pre-coated base layer is less than 10%, remove the dust, oil and loose mortar on the smooth surface of the sail in time, and repair and repair the pores if there are pores.

2. Wall reinforcing agent: brush the wall reinforcing agent, pay attention to the brushing to avoid paint leakage; For porous, dry and highly absorbent substrates, it is recommended to brush them after the first drying, and ensure that the wall reinforcing agent is dry and powder-free, and the paint is qualified.

3. Batch scraping putty: After the wall reinforcing agent is completely dry, select the interior wall putty series products for leveling and batch burial treatment.

4. Paint: What is the main function of wall reinforcing agent? Construction according to the requirements of interior wall coatings.