How to eliminate the current sound of Huawei earphones, and how to eliminate the current sound of ea

Many friends will encounter occasional faint current sound when using headphones. Although it doesn't have much impact, it does make the mood irritable. Thinking that the headphones I bought for hundreds of dollars, there would be an electric current sound when I put them on, is it a defective product?

We understand these feelings and questions very well. Therefore, the magic card master will first explain to you here why there is an electric current sound and how to solve it.

When you use the earphones while charging, you hear the sound of electricity. This is probably one of the most common. Because the mobile phone itself is a portable device with multiple functions, the internal components will interfere with each other and affect the sound quality.

In addition, the contact problem of the cable connecting the earphones and the monomer resolution of the magic card master earphones themselves.

Very high, very sensitive, and the charger or use the adapter with charging function, the circuit design is generally not good, without overcurrent protection, the current will be parsed by the earphone, which will cause the current sound to appear. So it's best not to charge or not to use an adapter with a charging function.

If you listen to the current sound normally, you can go to the mobile phone settings to turn off the sound effect, clean up the memory, and restart it, the built-in sound effect of some mobile phones will deteriorate the sound quality and cause the bottom noise or current sound.

If none of this works, then you can only use some headphones with high impedance, or low sensitivity and low resolution. The easiest way is to go directly to ** to buy a high-resistance rod, that is, to increase the impedance of the headphones.

adapters or adapter cables.

Okay, that's all for today's sharing, we'll see you next time.

Click on "Speakers" and "Properties" below.

Find "Level" in the properties of "Speaker", and change the number of "Microphone" below to 0.

Make sure that the computer is plugged into the microphone, in the sound properties, click on "Microphone", and then click on "Properties" below.

In the microphone properties, find the level again and change the number in the microphone acceleration to 0.

Check how well the test sound works, you can plug and unplug our microphone a few more times.

4. If the headset is plugged into the computer and the microphone is in a strengthened state, then the computer headset will have an electric current sound, and the reinforcement of the microphone is generally removed, so that the current sound of the headset can be eliminated.

5. If you plug the headset into the computer, if there are more junk files on the computer, it will cause the computer to respond slowly, which will cause the headset to produce current sound, you can clean up the junk files in the computer, and you can eliminate the current sound of the headset.

The headphones have current sound cancellation methods as follows:

1. Eliminate the cause of debris and the cause of the line. Min Qianling first cleaned the headphones to see if there was any debris inside. If you have a problem with the headphone jack connector, first dip cotton in a small amount of alcohol, wipe the plug, and then wipe it with a paper towel.

2. Twist the parts of the cable and keep the earphones still, if the noise changes with the twisting of the line, it should be a problem with the line, if there is a problem with the line, you can try to change the line.

3. Secondly, when someone around you is powering or has a strong electromagnetic field, it will also cause the Bluetooth headset to have a current sound, or if you are holding two mobile phones at the same time, the distance is too close, there will also be a very strong current sound. For this reason, it would be nice to change places or put another phone farther away.

4. See if the earphone cable is broken or loose, rule out the appearance of hardware damage, and finally if all kinds of inspection of the earphone are found to be no problem but there is still a current sound, you can contact the seller, after-sales return, inspection and maintenance.

5. The computer has static electricity, which is also the main reason. Touch the iron part of the computer case with your hand, and if the current sound disappears, put a piece of copper wire, one end to the screw behind the computer, and the other end to the ground. Whether the microphone is in a reinforced state.

I remove the microphone reinforcement. Because some sound cards don't support it.

6. If there is a problem with the driver, you may be using the driver that comes with the system, or there is a problem with the driver, if so, you can change a sound card driver. Bridge Qi.

If your Huawei Bluetooth earbuds have an electric current sound, you can try the following methods to eliminate it:1Replace the battery or recharge:

In general, a low or undercharged battery can also cause an electric current sound, and charging and replacing the battery can solve the problem. 2.Re-pairing:

Disconnect the Bluetooth Zen Hall headset from your device and pair it again, and see if there is still a current sound after reconnecting. 3.Clean up your headphones:

The sound of current may be caused by a blockage inside the earphones or excessive dust, so you can use a clean, soft cloth or cotton swab to gently wipe the inside of the earphones. 4.Keep your distance:

It is recommended to keep your mobile phone or other devices at a certain distance from your Bluetooth headset to avoid interference and generate current sound. If none of the above methods can eliminate the current sound, we recommend that you contact Huawei's customer service staff for further assistance.

Answer: Clean up the system junk files, which can alleviate the current sound caused by slow operation; The grounding wire for the main chassis can solve the current sound caused by static electricity in the chassis; Finally, open [Control Panel] - [Hardware & Sound] - [Manage Audio Devices] - [Recording], open [Microphone Properties], select [Level], and turn [Microphone Strengthening] down.

Question: Do I use AU recording, do I do the same?

If it's something else, you'd better try it out first.

Question: Or do you want to try this operation first?

I'm a laptop, how do I ground the wire.

Answer: Yes. 1. First unplug the external power supply and use the battery for power supply. If the vulnerability condition disappears, then it means that it is a problem with the ground wire of the socket, enter the second step below, if there is still leakage, then contact the dealer for repair.

2. Confirm whether the socket is grounded, and a simple way to do it is to use a pen or multimeter to test the socket. If the ground voltage is zero, the socket is grounded. Go to the third step below, otherwise change the socket or re-route the ground wire.

3. The insulation performance of the shell of the power supply suitor or laptop is not good, and the relevant accessories should be replaced. In addition, low temperatures are prone to static electricity and can also cause electric shock.

Hello, first of all, I can't be sure if there is a problem with your microphone or headphones, but the method of debugging on the computer is as follows: 1. Double-click to appear2) Click Properties to appear: 3) Select the first English option and click OK, and the following will appear

4) Tap Advanced 5) Remove the microphone reinforcement and turn the microphone volume down.

See if your headset and connector are in contact with the enclosure of the main chassis!

To Mike. Blow hard. It's a matter of static electricity.

This is very difficult, it is recommended to change to an expensive one, hehe.

<>2, click on "Raise your voice and use the weapon" and "Properties" below.

3. Find "Level" in the properties of "Speaker", modify the number of "Microphone" below, and change it to 0.

4. Make sure that the computer is plugged into the microphone, in the sound of the fundamental attribute, click "Microphone", and then click "Properties" below.

5. In the microphone properties, find the level again and modify the number in the microphone acceleration to 0.

6. Check how the sound effect of the test is, you can plug and unplug our microphone several times.

Many friends who often use headphone products may feel troubled because of the current sound that may be generated, indeed, these noises affect our audio to some extent**or**Appreciation, so how to eliminate the current sound of headphones?

1. If the headset only has current sound when used on the computer, but there is no such situation when used on the mobile phone, then you can try to clean up the system junk first, and the system optimizer or anti-virus software of the computer will bring this function.

2. Adjust the microphone rental attributes. Open the sound dialog box and select Interface. Turn on the speaker with both feet. Click on the selected level and set the microphone value to 0. After setting, go back to the sound dialog box, select Record, and set the microphone reinforcement value to 0 in the same way.

3. You can also choose to replace a high-end headset with strong anti-electromagnetic interference ability.

The reason why the headset will interfere with the use of the current sound, in addition to the computer is not cleaned up in time, resulting in a large amount of accumulated garbage, may also be due to the damage of the headset or some other reasons, so before solving, you should try to find out the original fault of your headset problem, and then comprehensively analyze and solve the problem.