What should I do if the cement mortar sticks to the threshold during decoration?

The cement mortar stuck to the threshold during decoration can be removed, and it can be washed with hot water with a shovel.

Basically, home decoration will be pasted with tiles, whether the tiles are good or not, whether the later use will occur hollow, detached, etc., and the master's craftsmanship is inseparable, in addition to the master's craftsmanship, whether the tiles are good or not, what materials are used to paste is also very important!

Don't use cement mortar for home decoration tiles, it is popular to do this now, regret the wrong one!

Home decoration tradition is the use of cement mortar to paste tiles, even if the master is good, because the cement mortar is difficult to ensure uniform coverage, so cement mortar to stick tiles, hollow or falling off and other phenomena are happening from time to time.

Now home decoration tile paving, basically using a new type of adhesive - tile adhesive, tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting ceramic tiles, face tiles, floor tiles and other decorative materials, with high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction and other advantages.

Compared with traditional cement mortar, the tile adhesive is several times that of cement mortar, which can effectively paste large ceramic tiles and stones, and avoid the phenomenon of tile hollowing and detachment.

Compared with the complex process of cement mortar, the tile adhesive does not need to wet the wall base before pasting, does not need to soak the tiles, directly on the brushed wall base to apply evenly, and the tiles can be pasted and pressed evenly.

Tile adhesive has high requirements for the flatness of the wall and floor, and needs to be leveled. Therefore, under the condition that the wall flatness is ideal, the tile adhesive construction is more convenient and fast, and the technical requirements for workers are not high, which can save labor costs.

To remove the cement slurry from the door, a cement mortar cleaning agent can be used. The cleaning agent is suitable for cleaning gray matter, lime residue and cement thin layers on interior and exterior wall tiles, glazed tiles, full-body tiles, vitrified tiles, polished tiles, clear water tiles, terracotta products and natural stone. Used for stone, tile, concrete products, such as:

Surfaces such as block bricks, curbs, antique bricks, and cultural stones.

How to use cement mortar cleaner:

1. Spray cement mortar cleaning agent on the surface that needs to be cleaned, as shown in the figure below

2. Wait one minute for it to fully react with the cement mortar, as shown in the figure below

3. Depending on the reaction, judge whether the above steps need to be repeated, if there are still more stains, the above steps can be repeated; As shown in the figure below:

4. Finally, clean the position polluted by cement mortar with water, as shown in the following figure

Can the grout be wiped off with a towel? Can it be washed off with detergent? If the cement slurry on the door is freshly stained, quickly flush it with water, then brush it with a brush, and finally wipe it clean again, and then it can be removed.

If it has been solidified, if the thickness is thin, you can use a small hammer to knock off the cement slurry one by one, and then clean and wipe it with a brush.

Cover it with a damp rag or damp towel for a while, and you can wipe it off!

Cement slurry can be removed with cement buster.

Decoration door glued cement removal method:

1. Clean it with dilute hydrochloric acid or dilute sulfuric acid used in the laboratory of the cement plant, because the cement is alkaline and melts or dissolves when it encounters acid. However, strong acids can damage the ground where the cement has solidified.

2. Clean with cement cleaning agent. Generally, cement cleaning agent is composed of compound acid, resist and descaling accelerator, which can quickly and thoroughly dissociate the accumulation of cement scale, rust scars and other minerals, so that the sediment and the sediment in the cement scale are washed away together. Generally, the cement cleaner needs to be diluted before use.

However, cement cleaners are acidic, so be careful not to contact them for a long time**.

Use the tool to scrape the putty gently and gently pull it off, so as not to damage the skin of the door.

This is very difficult, you can only use a small shovel to remove the large ones little by little, be careful not to hurt the car paint, the remaining traces, wipe slowly with a rag dipped in vinegar, because the cement is alkaline, how much can be wiped off with acid, and finally wiped clean with water to prevent rust on the car body, remember to wear gloves.

Hope it helps! In the future, pull cement or something, pay attention, there is really cement on it, clean it up as soon as possible, and it is difficult to clean up after hardening.

You can use a soft material and add water.

At present, I have not found any tips in this regard, and when the cement is dry, it will be dropped with a button by hand.