The plastic steel window can t be removed, is there any good way to solve it?

Pry off the other edge banding, then unscrew the screws of the wheels, and remove the damaged plastic steel door and window pulleys. Then pour in an appropriate amount of white vinegar and baking soda.

It reacts with white vinegar to form a substance that effectively removes dirt. Otherwise, it would be more troublesome to scrape the slide, so I went to the building materials decoration city to buy a bunch of pulleys and came back, checked and replaced them one by one.

<> with double pulleys in the load-bearing, pushing and pulling lightness are better than a single group of pulleys, it is best to choose matching pulleys, so that there is no deviation in size, left and right. It can be replaced, it is best to find a nearby store to repair it, because it is possible to remove the window sash to view, it is very dangerous to be unprofessional, it should be that the rollers in the groove under the window sash are damaged, and you can find a professional master to replace the rollers. The strength of the material is not as good as before, and the pulley is generally not easy to use after deformation, stuck, tight, and sneering, which is a very poor experience.

Remove the sliding window.

Later, it was found that the pulley was made of plastic, and it had been damaged after nearly ten years of use. Clean up regularly, and don't have hard debris blocking the middle of the runway, and it is generally not too much of a problem. The easy way is to find a plastic steel window.

The shop asked a worker to knock down the window of your house, and it couldn't be used.

It is difficult to install, it is all technical work, otherwise the form is easy to deform. So it's best to do it by professional or semi-professional people. <> with double pulleys in the load-bearing, pushing and pulling lightness are better than a single group of pulleys, it is best to choose matching pulleys, so that there is no deviation in size, left and right.

Can be replaced, it is best to find a nearby store to repair, because it is possible to remove the window sash to view, unprofessional is very dangerous material strength is not as good as before, generally deformed after the pulley is not easy to use, after removing the sliding window found that the pulley is a plastic material, nearly ten years of use has been damaged, in a treasure bought a few after the replacement of Lili Soso push and pull. Jam, tight, and snorting, is a very poor experience. Clean up regularly, and don't have hard debris blocking the middle of the runway, and it is generally not too much of a problem.

This situation is generally because the plastic strip on the side of the plastic steel window is restricted, so you can take a closer look at the upper and lower grooves on the side of the sash, and this plastic strip also belongs to the anti-theft board, it just uses the plastic clip to get stuck on, so we can use a screwdriver to gently pry it off, and the window sash is removed in this way. After completion, the anti-theft plate should be installed, and if there is a window lock blocking it, the lock must be removed first.

I have never removed the plastic steel window, I feel that it is difficult to remove it without the help of special tools, so it is recommended that you find a special person to solve it.

Summary. Hello dear, what you asked, "The plastic steel window can't be removed, is there any good way to solve it?" The answer for you is as follows + answer:

1. Generally speaking, the choice of plastic steel windows is two windows, we need to push the two windows together, and then overlap them. Remove the seal first and gently pry along its gaps. Next, hold one of the window sashes on the outside with both hands, lift it up firmly, and move the bottom out of the track as you lift.

2. Then force down to let the upper window out of the window frame, and you can take it off directly, and the inner window can be removed in the same way. 3. In the process of extraction, it may be limited by the sealing strip, we can remove the sealing strip and gently pry it off along its gaps, and some may be pasted with sealant, so we can remove the sealant first, and then disassemble the sash, which will be easier. 4. In the process of disassembly, there is a protruding object in the upper groove of the window frame that may be blocked, which is used to limit the position, so it is generally fixed with screws, and the screws need to be unscrewed first, and then disassembled.

The plastic steel window can't be removed, is there any good way to solve it?

Hello dear! I have seen your question on my side and am trying to sort out the answer, and I will answer you later, please wait a moment

Hello dear, you asked, "The plastic steel window can't be removed, is there any good way to solve it?" The answers provided for you are as follows + answers: 1. Generally speaking, the plastic steel windows are two windows, and we need to push the two windows together and then overlap them.

Remove the seal first and gently pry along its gaps. Next, hold one of the window sashes on the outside with both hands, lift it up firmly, and move the bottom out of the track as you lift. 2. Then force down to let the upper window out of the window frame, and you can take it off directly, and the inner window can be removed in the same way.

3. In the process of extraction, it may be limited by the sealing strip, we can take off the sealing strip and gently pry it off along its gaps, and some may be pasted with sealant, so we can remove the sealant first, and then disassemble the sash, which will be easier. 4. In the process of disassembly, there is a protruding object in the upper groove of the window frame that may be blocked, which is used to limit the position, so it is generally fixed with screws, and the screws need to be unscrewed first, and then disassembled.

If the sealing strip is fixed tightly, it is also recommended to use a screwdriver to carefully pry open from the bottom of the sealing strip. The sealing strip** is relatively low, so even if it is damaged, the integrity of the PVC window screen can be ensured. Once the seal is removed, lift the entire strainer to the top of the slide and remove the entire sash.

During the disassembly process, there may be a slight deformation of the outer screen, which is normal, it is recommended not to adjust it, if it is necessary to adjust it again according to the professional.

<> the longitudinal thread is too short and still plastic, it is tightened for fear of screwing the slippery wire, and a little loose but leaking water, haha, it makes people cry and laugh. In fact, the structure and quality of online purchase are selected by themselves, and those who know how to do it can know it at a glance. So why is the use rate of plastic steel windows getting lower and lower in recent years?

What are the problems with it?

The outer layer of plastic is pulverized, and even more than most of the materials used in individual doors and windows are not plastic steel at all. So if the window is badly damaged and you want to replace the window, I suggest that you remake aluminum alloy windows, including indoor sliding doors, and don't use products made of this material. If the ventilation is relatively large, buy a larger size of the wool top and put it in, but this can only reduce the air leakage can not completely solve the air leakage, if you are too sensitive to the wind, it is better to replace the window with a sliding window, and the sound insulation effect of the sliding window is better.

The window sash is small and breathable, and the lap of the window sash is not easy to breathe. Fourth, the most important thing is that the installation must be horizontal and vertical, the styrofoam should be full, and the width of the sealant should be about two centimeters. All of them should not be breathable.

In the Northeast, it is recommended to install double-layer plastic steel windows. The gaps between the windows can be filled directly with a sponge, and then the windows are sealed with a layer of plastic sheeting. After installing the plastic sheet, it can achieve an airtight effect and can maintain the warm temperature inside the house.

The seal is not good. Due to poor sealing, many plastic steel windows will leak air.

Can be remedied. There are several reasons for the air leakage of plastic steel doors and windows: 1. The size of the window sash is small, resulting in insufficient overlap between the upper and lower or left and right.

2. The sealing wool strip used is a non-standard consumable, which affects the sealing.

3. There is no air block installed in the middle of the upper and lower tracks of the frame, or there is no dislocation opening inside and outside when milling the drainage hole, and the drainage hole cover is not covered.

4. The window sash is too high, the steel lining inside the cavity is too thin, or there is no steel lining, resulting in the fan bending and deformation and air leakage when the wind blows.

5. The installation of the window frame is unqualified, the lower track is not horizontal, and the fan is inclined after being installed, and it cannot be adjusted, resulting in poor closing.

6. The main material and auxiliary material model of the material are not matched, (but this is not difficult to identify by the industry).

<> remove the sealing plastic strip and lift the entire window up by hand. The plastic steel window is not easy to disassemble, if you want to remove the plastic steel window, you must first remove its sealing strip, so that the frame of the plastic steel window can be messed up with a relatively large gap, easy to disassemble, and then use your hand to lift the entire plastic steel window up, and use the other hand to break the lower frame of the window from the window frame, and then pull it down, so that the whole plastic steel window can be completely removed from the window frame.