Window plastering and closing need to be pressed window frame practice

What is the method of plastering and closing the windows?

1. If you want to plaster the window, then you must re-release the vertical line before closing, and check it, if the position, verticality, and horizontality of the vertical line do not meet the relevant construction requirements, then you need to notify the chief foreman.

2. Only when the chief foreman is qualified can the next construction process begin. If the window is blindly used as a control line to close, it is generally easy to lead to rework, and each construction worker needs to bear their own responsibility.

3. Before plastering the window, the debris and dust at the window closing position should be cleaned up, and some water should be sprinkled for wetting, after wetting, the cement mortar should be modulated according to the ratio of 1:2, and then the prepared cement mortar should be used to plaster the window closing position in layers.

4. When plastering and closing the window, the outside of the window should generally use cement mortar to press the aluminum alloy window frame about 5 mm to 8 mm. When the plastering of the window is done, it is necessary to ensure that the finished window frame is exposed about 10 mm to 12 mm, and the drain hole of the mullion must be kept exposed, so as to facilitate drainage. In addition, the windows on the façade must be in the same straight line, and the façade size of the opening must be vertical and square.

5. There should be no slope in the window of the plastering surface on the inside of the window, and the indoor window sill part should be about 3 mm to 5 mm higher than the root of the outdoor window sill, that is to say, the inner window sill must be higher than the outer window sill, and all should have a square size.

<> first of all, before closing the mouth, the group should place the vertical line and carefully proofread, the inexperienced can consult the decoration foreman, and secondly, before the closing of the window, the debris and dust placed in the window need to be removed and cleaned. When closing, the proportion of cement is also required, it is best to mix the ratio of one to two, and then the evenly mixed cement slurry is layered to close the window, and the window frame of the closing surface should be ensured when closing, and at the same time, it is necessary to ensure that the hole is horizontal and vertical with the ground, and if there is a deviation, it should be corrected immediately until it is vertical.

What to wipe the doors and windows glass with.

If you want to wipe the doors and windows clean, you can't do it without skills, what to wipe the doors and windows with, you can use the following methods to wipe them:

1. When wiping the glass, it is recommended to wipe it with warm water, and then add a little dish soap Huaixiang, which can not only quickly remove the stubborn stains on the glass, but also make the glass as bright as new.

2. You can also dissolve the unused soap at home in warm water, and then wipe the glass with a rag dipped in soapy water, and wipe it again with a newspaper.

3. Dip a soft cloth with a little wine or vinegar, gently wipe the glass, and then repaint it with chalk powder or gypsum ash after wiping, wipe it clean and then dry it with a dry cloth to instantly make the glass look new.

In addition, there are two tips for wiping the glass of doors and windows, which are skillfully using fabric softener and skillfully wiping with soap.

1. Skillfully use the disadvantage of the big fabric softener.

First of all, wipe the glass with warm water, wipe it again, and then wipe it again with a rag dipped in a small amount of softener, the softener has a strong antistatic effect, and the glass can be wiped for a long time without dust, this method can also be used to mop the floor and wipe the table.

2. Wipe with soap.

There is also a very simple method, as long as there is soap at home, the soap can be dissolved in warm water, and then wipe the glass with a rag dipped in soapy water, and then wipe it again with a newspaper. In this way, the glass will be shiny and shiny, and the glass is not easy to fall dust, and it looks very clean.