Midea water purifier has been draining? Why does the water purifier keep draining?

If the solenoid valve of the water purifier is damaged, it will not have any effect at this time, not only will the waste water flow, but also a large amount of pure water will flow out, so it will lead to a lot of wastewater, it is best to ask professional personnel to come to check and repair the replacement of the solenoid valve. 2. It is also possible that there is a problem with the electric control board of the water purifier, if it has been in the state of discharging wastewater, it may be a problem with the electric control board. 3. Nowadays, many water purifiers use reverse osmosis membranes.

With the use of time, the reverse osmosis membrane will be blocked by some impurities, so it will cause pure water to be unable to pass through, resulting in more and more wastewater, and it will continue to produce wastewater flowing out.

If the filtration parts or other parts of the water purifier are damaged, there will be wastewater, and a large amount of pure water will flow out, so it will lead to a lot of wastewater, it is best to ask professional personnel to come to the door to inspect and repair the damaged parts. It is also possible that there is a problem with the electric control board of the water purifier, if it has been in the state of discharging wastewater, maybe it is the problem of the electric control board. After a long time, the reverse osmosis membrane will be blocked by some impurities, so it will cause pure water to be unable to pass through, resulting in more and more wastewater, and it will continue to produce wastewater flowing out.

It should be that the filtration system is broken.

When the water purifier has been draining mainly due to a number of reasons, if the high-pressure switch has a problem, it will cause the wastewater to flow all the time, at this time it should be sent to a professional master for maintenance, or the problem of the water purifier, due to the large amount of wastewater discharged, so there has been a situation of discharging wastewater.

The reason why the water purifier keeps draining water.

If the water purifier has been draining, it is necessary to consider whether there is a problem with the high-voltage switch, if the machine is full of water, the high-voltage switch will jump, so as to disconnect the power supply, if there is a problem, the machine will always work, resulting in the waste water inside has been flowing, at this time, it is advisable to ask a professional time for maintenance.

If the water purifier has been draining, it may also appear on the pure water machine, and the pure water machine is also divided into grades in the discharge of wastewater, usually the ratio of pure water to the discharge of wastewater on the market is 1:3, so that the waste of water will be very large, so there will be a situation of discharging wastewater all the time.

If the electric control board of the water purifier is damaged, the water purifier has been in a state of flushing, which will also cause a large amount of waste water of the water purifier.

When the water purifier has been draining mainly due to a number of reasons, if the high-pressure switch has a problem, it will cause the wastewater to flow all the time, at this time it should be sent to a professional master for maintenance, or the problem of the water purifier, due to the large amount of wastewater discharged, so there has been a situation of discharging wastewater.

The reason why the water purifier keeps draining water.

If the electric control board of the water purifier is damaged, the water purifier has been in a state of flushing, which will also cause a large amount of waste water of the water purifier.

Summary. Kiss.

1. The reason why Midea water purifiers do not produce water or have very little water.

1.The pressure of the pressure drum is released.

2. Plugging after activated carbon.

3.Test whether the ball valve of the pressure barrel is damaged.

4.The first three filter elements are blocked.

5. The pressure of the high-pressure pump is insufficient.

Membrane blockage. 7. The proportion of wastewater is unbalanced or the wastewater valve is not closed after the activated carbon plug.

8.Pressure drum pressure is insufficient or internal faulty.

9.The water temperature is too low, and the raw water pressure is too low. Water purifiers.

Second, the solution of Midea water purifier does not produce water.

1.Check the water purifier pipeline and straighten out the water purifier pipeline;

2.Check the power supply of the water purifier and turn on the 220V AC power of the water purifier. If the power supply of the water purifier is normal, check the output voltage of the transformer;

3.Check whether the high-voltage switch or float switch is faulty and cannot jump back;

4.Check whether the inlet solenoid valve is normal. Unscrew the water outlet of the solenoid valve, turn on the power supply, and check whether the water flow is smooth.

5.Open the raw water ball valve and check whether the filter element is blocked before the reverse osmosis membrane, such as replacing the blockage;

6. If water is ingress, the solenoid valve is damaged;

7. Check whether the pump pressure of the booster pump meets the requirements. If it is lower, it needs to be replaced;

8.Open the pure water inlet of the reverse osmosis membrane. Without water, the reverse osmosis membrane will be damaged;

9.Check whether the wastewater discharge is too large and whether the ratio of pure water to wastewater is unbalanced;

10.Check whether the activated carbon filter is clogged after inspection.

Midea water purifier has very little water, what's going on?

Midea water purifier has very little water, what's going on?

Kiss. 1. The reason why Midea's water purifier does not produce water or has very little water 1The pressure of the pressure barrel is released by the liters.

2. Plugging after activated carbon. 3.Test whether the ball valve of the pressure barrel is damaged.

4.The first three filter elements are blocked. 5. The pressure of the high-pressure pump is insufficient.

Membrane blockage. 7. The wastewater valve is not closed after the proportion of wastewater is unbalanced or the active carbon plug is noisy. 8.

Insufficient pressure in the pressure barrel or failure of the inner sail. 9.The water temperature is too low, and the raw water pressure is too low.

Water purifiers. Second, the solution of Midea water purifier does not produce water1Check the water purifier pipeline and straighten out the water purifier pipeline; 2.Check the power supply of the water purifier and turn on the 220V AC power of the water purifier.

If the power supply of the water purifier is normal, check the output voltage of the transformer; 3.Check whether the high-voltage switch or float switch is faulty and cannot jump back; 4.Check whether the inlet solenoid valve is normal.

Unscrew the water outlet of the solenoid valve, turn on the power supply, and check whether the water flow is smooth. 5.Open the raw water ball valve and check whether the filter element is blocked before the reverse osmosis membrane, such as replacing the blockage; 6. If water is ingress, the solenoid valve is damaged; 7. Check whether the pump pressure of the booster pump meets the requirements.

If it is lower, it needs to be replaced; 8.Open the pure water inlet of the reverse osmosis membrane. Without water, the reverse osmosis membrane will be damaged; 9.

Check whether the wastewater discharge is too large and whether the ratio of pure water to wastewater is unbalanced; 10.Check whether the activated carbon filter is clogged after inspection.

The main reason is likely to be caused by the poor water supply, such as regional renovation of water pipes and power repairs, which often lead to water supply interruptions, and it is very simple to solve such problems, just wait for the water supply to be normal. The reason may be that the water purifier filter is too dirty, and the water purifier needs to be replaced or cleaned after about half a year to a year. If it is a replaceable filter, it is recommended to replace it directly.

The reason may be that the water purifier outlet is blocked, it is recommended to boil it with hot water, and the blockage can fall off by itself. In addition to the above reasons, the water purifier will not produce water, there are also the following reasons: 1. If the motor failure water purifier makes a hmm-huh sound or simply does not work, then most of the problems come from the core components:

Motor. The motor is located at the end of the water purifier and needs to be opened to inspect the lid. It is recommended that users call customer service ** or find professionals to repair, do not open it yourself, on the one hand, it is easy to cause secondary damage, and there is no professional equipment can not monitor whether there is something wrong with the motor.

Second, the water purifier and the faucet need to be closely connected, and the huge water pressure triggers the resistance of the water purifier to make the water purifier start working. The user can first check the bayonet of the water purifier and faucet, and if there is water leakage, then the bayonet needs to be retightened or replaced.

If the water purifier is a reverse osmosis water purifier, there are two possibilities for this situation, one may be caused by the failure of the water purifier, and the other may not carefully observe whether the water purifier is in a state of water production when draining, if the water purifier is not in a working state, and the wastewater has been discharged non-stop, it means that the water purifier is broken and needs to be repaired. For the reverse osmosis water purifier in order to protect the membrane, there must be wastewater discharge, which is a normal phenomenon, you can take a closer look at it, and then decide on the treatment method.

Speaking of water purifiers, I believe everyone knows a lot. In recent years, with the continuous pollution of water resources in our living environment, people generally choose water purifiers as water purification equipment. So, in the face of many water purifier brands on the market, do you know that the water purifier of the United States generally does not produce water, what are the specific fault principles and some solutions?

The pressure of the pressure barrel is discharged. Post-activated carbon clogging. Whether the pressure barrel ball valve is damaged.

The first three filter cartridges are clogged. The pressure of the high-pressure pump is insufficient. RO membrane blockage.

The wastewater ratio is out of balance or the wastewater valve is not closed tightly and the rear activated carbon is blocked. Insufficient pressure in the pressure barrel or internal destruction. The water temperature is too low, and the raw water pressure is too low.

Check the pipeline of the water purifier and straighten out the pipeline of the water purifier; Check the power supply of the water purifier, turn on the 220V AC power of the water purifier, if the input power supply of the water purifier is normal, check the output voltage of the transformer; Check whether the high-voltage switch or float switch is out of order and cannot jump back; Check the water inlet solenoid valve to see if it is normal. Unscrew the water outlet of the solenoid valve, turn on the power supply, check whether the water is connected, if the water is not connected, transfer to the next step of testing; Open the raw water ball valve to detect whether the filter element in front of the reverse osmosis membrane is blocked, such as plugging and replacement; If the water is passed, the solenoid valve is damaged; Check whether the pressure after pumping the booster pump meets the requirements. If it is lower than the need to replace; Open the pure water port of the reverse osmosis membrane, if the water does not appear, the reverse osmosis membrane will be damaged; Check whether the amount of wastewater discharge is too large, so that the proportion of pure and wastewater is out of balance; Check that the post-activated carbon filter is not clogged.

The above is the relevant content of the fault analysis and treatment of the water purifier of Midea water purifier introduced to you. For the Midea water purifier, I believe that everyone is more trusting and loving this brand, whether it is from the quality, or from the brand's reputation, people are more favored. Therefore, when encountering a problem with the water purifier, everyone can first introspect to understand the cause of the failure, and then see how to deal with it.

Well, I hope that the introduction will help you.

The pipeline machine of the Midea water purifier does not produce water The pipeline machine of the Midea water purifier does not produce water (1) The new machine needs to turn on the water switch, and the water will be discharged after about 10-20 minutes of internal air.

2) If the machine has been used for a period of time, it may be caused by blockage, and it will be handed over to the after-sales service.

There are several possible situations, one is that the post-filter element is clogged and the filter element needs to be replaced, and the other is the reverse osmosis membrane.

Aging damage, need to replace the reverse osmosis membrane, the third is the booster pump.

Fault, need to repair or replace the booster pump, the fourth is that the solenoid valve can not operate normally, to check the solenoid valve power supply, or replace the new solenoid valve. 1. The water purifier usually has at least three sets of filter elements, and the last group is the post-filter element, which is usually filled with activated carbon.

After a long period of use, it will be clogged with impurities, and the water output will become smaller and smaller. Activated carbon itself is a consumable and needs to be replaced in time, which is also good for water quality. 2. The core part of the water purifier is the reverse osmosis membrane, which can filter out the dissolved magazines in the tap water, but it will gradually clog with use, resulting in poor water output.

Usually there is a time to replace the filter membrane on the manual, and it should be replaced in time after the service cycle. 3. The booster pump is used to pressurize the water, because the reverse osmosis membrane needs a certain pressure to work, so the water purifier with this principle.

There will be a booster pump inside. If the booster pump is not working properly, it will not be able to filter and will not produce water. The failure of the booster pump may be due to the power supply and the circuit needs to be repaired.

If the booster pump itself is broken, the pump body needs to be replaced. 4. The solenoid valve is a water valve controlled by solenoid, which may not produce water after it is broken, or it may cause water leakage, and it can be replaced with a new solenoid valve.