How do you replace a water dispenser faucet? Is there a specific method?

How to replace the tap of the water dispenser:

1.Unplug and cut off the power supply.

2.Take the water dispenser bucket down or drain the water.

3.Remove the back cover screws and open the back cover.

4.Unscrew the faucet nut (some are plastic strapping ropes) outward, and pull out the faucet you want to change5Reinstall according to the unloading method.

First of all, turn off the main water gate of the house. The purpose is to ensure that there will be no splashing during the process of dismantling and replacing the faucet, which will cause unnecessary trouble.

After closing the sluice, wait a few minutes to make sure the remaining water in the faucet is completely drained before proceeding with the follow-up operation, or take a discarded towel to absorb the water to reduce the waiting time.

Use a knife to pry open the protective sheet on the faucet handle, this protective sheet is just glued on, and it is easy to pry.

Select a screwdriver of the corresponding model (slotted mouth, cross mouth, etc.) to unscrew the screws of the faucet handle. Remove the faucet, because the faucet handle is fixed with occlusal tooth patterns, so the disassembly process requires a little force.

Open the bottom hinge, the disassembly work is completed, and the relevant tools should be sorted out in time.

Install the new faucet with the reverse steps above.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

1. Before replacing the faucet, we need to prepare a new faucet, water adhesive tape and a wrench.

2. Close the main valve of the water source to facilitate the follow-up work. (It's important to keep in mind this step before you get a splash when you remove the faucet.)

3. Hold the faucet with a wrench, and after adjusting it to the appropriate position, press the wrench with your thumb to slide the mechanism button, and unscrew the broken faucet in a rotating way.

4. After screwing to a certain looseness with a wrench, you can directly unscrew it by hand, and you will see that there is residual water and a little rust at the interface between the wall and the faucet, and wipe it clean with a rag.

5. Wrap the threaded part of the new water hose with water adhesive tape, about ten times or so, and feel a certain thickness. First, install the new faucet to the wall interface in a rotating way by hand, and then slowly tighten it with a wrench, adjust the angle of the faucet, so that you can't see the water adhesive tape, and feel that you can't screw it in, which is better.

6. Open the main valve of the water source, open the faucet to see if there is water seeping out from the interface, if there is seepage, it means that the water adhesive tape is too little winding, and it is necessary to unscrew it and re-wrap the water adhesive tape.

Don't worry about replacing the faucet at home, just replace the broken new faucet in time, but how to replace the faucet? Many friends who change the faucet for the first time do not know how to start, here I want to teach you how to replace the faucet, so that when you encounter the replacement of the faucet, you can easily replace the broken faucet with a new faucet. Of course, in addition to teaching everyone how to replace the faucet, we also have to teach everyone the knowledge of daily maintenance of the faucet.

Step 1 of replacing the faucet, turn off the water supply, just turn off a water supply valve near the faucet to turn off the water supply, but if not every faucet is equipped with a water supply valve, you have to turn off the main water supply valve to close all water supply. 2. Push-type faucet: No matter what kind of appearance the press-type faucet has, whether it has two handles for hot and cold water or only one handle that controls hot and cold water at the same time, it works according to some basic principles.

3. Remove the small screws on or behind the faucet handle to remove the handle fixed to the faucet body. Some screws are hidden underneath metal buttons, plastic buttons, or plastic pieces that snap into or screw into the handle. As soon as you turn the button on, you will see the handle screws mounted on the top.

4. Use an adjustable wrench to remove the filling nut, being careful not to leave scratches on the metal. Rotate the spool or shaft in the same direction as when you turn on the faucet to unscrew them. How to change the faucet seal 1. Turn off the water supply and remove the faucet handle.

2. Unscrew the filling nut and remove the nut and the old sealing ring from the valve core. 3. Install a new sealing ring. If you are using a wire sealing material, wrap it around the spool a few times.

In the case of sealing materials such as soft wires, only one loop is wrapped around the spool. 4. Before reassembling the faucet, apply a thin layer of petroleum oil to the threads of the valve core and the threads of the filling nuts. Daily maintenance of the faucet 1. After using it for a period of time, if it is found that the water output is reduced, or even the phenomenon of the water heater going out, the faucet may be blocked.

2. The faucet that has not been used for a long time will sometimes occur incomplete closing, leakage, loose handle, loose connection port and water leakage, etc., usually due to hard debris stuck in the sealing port, just remove the handwheel and unscrew the valve cover, clean up the impurities around the valve core and install it as it is to resume normal use. Whether you want to remove a broken faucet or replace it with a new one, you need to remember to turn off the water valve of the faucet to ensure that it does not run water when replacing the faucet. When replacing the faucet, you need a lot of special tools, such as a wrench is one of the most necessary tools to change the faucet, and you must make sure that the tools are complete when changing the faucet.

The tips for daily maintenance of the faucet are very important, and the correct maintenance can enhance the use effect and service life of the faucet.

The appearance of the faucet brings great convenience to our modern living water, and it is a thing that is used frequently, so it often needs to be replaced. Next, PCHOUSE will introduce to you how to replace the faucet.

1. We all know that there is generally a total switch under the kitchen faucet, and the total switch can be turned off before replacing, if there is no total switch under the kitchen faucet, you need to go outside or the balcony water tower to turn off the total switch. In general, the first step is to turn off the main switch and cut off the water source.

2. After turning off the water source switch, please go to the water injection pipe to find the interface of the faucet, pinch the metal joint above the water pipe, rotate it a few times to the left and right, and remove the old faucet.

3. After the water pipe is removed, put it aside, this is what you will find, the joints and walls of these water pipes are very dirty, and there are such pipes in the hardware store, you can replace the original old pipes. Because the original pipes have been weathered for a long time, leaking, etc., so you can also replace them while changing the faucet.

4. After removing the water pipe, please hold the faucet with your hands, and then rotate it left and right to loosen the faucet.

5. After loosening the faucet, you can easily remove the plastic knob under the faucet. Then the entire faucet can be removed.

6. Install the new faucet directly, and then turn on the general switch to test its use.

If the faucet in your home is broken, it needs to be replaced. So how do you replace the faucet? PChouse will take you to find out.

1. The most important step before disassembling the faucet is to close the main valve, otherwise it will lead to the spurting of tap water, not to mention the waste of water, but also increase the difficulty of cleaning.

2. Prepare the tools to be disassembled and the faucet parts that need to be replaced, and the tools are generally enough to have screwdrivers, wrenches and pliers.

3. Use a screwdriver to unscrew the handle screws on the faucet, and then you can split the faucet handle from the main body. This is for the faucet where the screws are exposed, if it is the kind of hidden screws, then open the external button or plastic sheet, you can see the handle screws, and the rest of the operation remains the same.

4. After removing the handle, you can see a nut, some are copper, some are ceramic, this is the valve core of the faucet, you can use a wrench to remove the nut, and then replace or clean the operation.

Before we can do it, we need to prepare three tools: a new faucet, water tape, and a wrench. In order to facilitate the subsequent operation, be sure to close the main valve of the water source first, otherwise there will be water splashing out when the old faucet is removed. Then follow these steps:

1. Use a wrench to jam the old faucet, adjust it to a suitable operating position, slide the mechanism of the wrench, and screw the old faucet until it is loose according to the rotation method.

2. After using a wrench to loosen it to a certain extent, you can use your hands to directly unscrew the old faucet.

3. After successful disassembly, you will see a little rust at the interface, and wipe the stain clean with a wool towel. This move is for the sake of water health in the future.

4. Take out the new faucet and wrap the threads of the faucet with water tape, generally 8-10 times.

5. Rotate the new faucet into the interface by hand, and then use a wrench to rotate it until it can't be screwed. Pay attention to adjusting the angle of the faucet when twisting the last few turns. When you can't see the water tape, it means it's almost screwed.

6. Open the main valve of the water source and test whether there is any water leakage. If there is no water leakage, the faucet has been successfully replaced. If there is a water leakage, it means that the water tape is not enough, at this time, take off the faucet, take the Yunchong to wrap a few more circles of water tape, and then screw it in.

Tool Attack Defeat Raw Material: Pai's Raw TapeTap.

1. Wrap raw tape around the faucet.

2. Insert the place where the faucet is to be installed, rotate and tighten it clockwise.

Maintenance method:1. The surface of the faucet should be gently wiped with a soft cloth (without impurities) dipped in detergent. Do not use metal wire balls or scouring pads with hard particles.

In addition, do not collide with hard objects to damage the surface of the faucet.

2. Use the following detergents to remove coarse and dry beats** and accumulations: mild liquid glass cleaner, pure liquid glass cleaner, acid-free, non-abrasive soft liquid or completely dissolved powder, non-frictional solution polishing agent.