iPhone 6 keeps showing headphone mode when it gets into water, what to do

iphone6plus water ingress display headphone mode reason: headphone jack socket water damage mobile phone water after water treatment methods are as follows:

1.Shutdown: This is definitely the first step to save the phone, no matter how much water ingress the phone, please turn it off first, otherwise it will burn out the circuit directly.

2.Check the location of water ingress: In most cases, the location of a large amount of water ingress into the mobile phone is generally the headphone jack and charging hole, because as long as it is not broken in other places, there are no cracks.

3.Check for external damage: if it's simply soaked in water, it's not a big problem. However, if it rains and falls out, check whether there is any cracks in the phone and water in.

4.Simple water intake: If it is just a simple water intake, then take a hair dryer, adjust to the cool breeze setting, and dry it with a small breeze. Since most of the water enters from the headphone jack, the phone should stand up.

5.Wait a few days before turning it on: simply enter the water, when the phone is dried, you can turn on the phone and use it normally, of course, if you can't turn it on, it can only be that the water enters too much, and the circuit inside is broken. It should be sent for repair in time.

iPhone does not plug in the headphones to display the headphone mode, mainly caused by the system and hardware, the system may identify the headphone mode error in some cases, and the hardware is the earphone socket into the dust or water caused by poor contact. Here are the steps to resolve it.

System: Settings - General - Accessibility - Audio Calling - Select Speaker; Dial**, choose to use the speaker after connecting, and then switch the audio call mode to automatic.

Hardware: Try to plug and unplug the headphones a few more times, and you can also use facial tissues (to be flexible and not slag) twisted into a small stick, and gently screw into the jack in the direction of the twist, bring out the dust, and see if it can return to normal. If it does not return to normal, you will need to replace the headphone socket.

First, clean up the water stains, then turn off the phone and restart it to see if the headphone mode can be removed.

2. Restore your phone to factory mode, take iPhone 6 as an example, the specific method is as follows:

1. First click "Settings" on the desktop of your iPhone 6 phone.

2. Select the "General" option after entering.

3. Then find the "Restore" item and click to enter.

4. Click "Reset All Settings" after entering.

3. If you still can't cancel the earphone mode after restoring the factory settings, you can bring your phone and warranty card to the official repair center of the Apple mobile phone for repair.

First turn it off, treat the residual water, and then use a cotton swab to clean up the headphone jack. Blow with a hair dryer if you can. It can also be sunbathed. Putting it in the rice for dozens of minutes can also absorb moisture. Finally, boot it up and test it.

I'll tell you a dirt way. Turn off your phone and put it in your rice pocket. 24 hours later. Charge your phone and take it out. After turning on the phone, try again, and you can basically solve this problem.

1.If the headphone mode is displayed after the Apple headphone jack is flooded, turn off the phone, find a needle, and gently poke the earphone hole, it may be when the earbuds are unplugged. The bouncing device inside did not return to its original position.

2.Swirl the headphone jack with a cotton swab to wipe the inner wall clean.

3.Turn off your phone and restart it to factory settings.

4.Place the mobile phone in a dry place such as putting it in rice, and after it is dry, turn it on and restart, if it is still like this, it is possible that the circuit inside is broken, and you should take the repair shop to find a professional to repair it in time.

When the tablet is flooded with water, the headphone mode appears, first dry the water on the surface of the earphone jack with a cotton swab.

2.Then put it in a ventilated place to dry for a few days to see if the headphone mode of the tablet can disappear.

3.It should be that the micro switch in the headphone jack is broken by water entering the tablet headphone jack, and it becomes the headphone mode.

4.If it still doesn't work, you should take it to the after-sales outlet for a professional to test it, repair or replace the new headphone jack, etc.

1.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

2.Wipe down the circuit board with anhydrous alcohol and try to turn it on.

Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

3.Send it to the repair center for repair as soon as possible (0755-23945679). If the motherboard is severely corroded over time, it will cause irreparable consequences.

If the headphone jack shrapnel problem is not the same, you need to go to the mobile phone repair to repair it.

How to deal with the problem of shrapnel in the headphone jack:

1. Blow the headphone jack down.

2. Plug in the earphones, turn them down, gently unplug them, and repeat several times.

3. Rub it into small strips with a paper towel, insert it into the headphone jack, and wipe off the debris.

iphone6 keeps showing headphone mode processing method:

1. Go to Mobile Settings - General - Accessibility Function.

2. For audio calling, select Speaker.

3. Or reset all settings.

Do not use a blow dryer, wait for it to dry naturally.

Dry it with a blow dryer and then shut it down and restart.

Just reset all the settings, just solved hee-hee