The gas stove has a battery, and there is no electronic spark when pressed, and the fire cannot be i

Gas stove ignition maintenance problem, gas stove can not fire is also divided into many situations, but no matter what the situation, first you have to do two kinds of checks:

1. Check whether there is gas. Xiaoju is not to tease you, sometimes you may be too busy with work and forget to buy gas, then naturally you can't catch fire, just go to pay the bill to buy gas.

2. Check whether the battery is charged. If the sound is soft and weak, the electric frequency is slower than before, and there is a clattering sound, if this happens, it is likely that the battery on your gas stove is insufficient, and a new battery will solve the problem. It is also possible that the positive and negative electrodes in the battery tray are rusty, resulting in poor contact, and the rust can be gently sanded off with gauze paper.

If the gas is sufficient and the battery is fine, then it should be analyzed on a case-by-case basis.

Situation: Situation 1: Let go and turn off the fire.

Gas stove ignition maintenance problem, hand press the knob can be normal fire, but as long as you let go of the fire will be extinguished, in this case you need to do the following checks:

1. Whether your operation is correct. Now the electronic ignition gas stove has a flame-out protection device, and it needs to be pressed for 5-10 seconds when ignition, and the induction needle can only be released after it takes effect.

2. Check whether the flame distributor of the gas stove is well placed. If the flame splitter and flame splitter seat have bayonets, the bayonet must be aligned. If the buckle is displaced, it will not only let go of the flame, but also cause the flame separator to burn and deform, and the fire separator will be scrapped after a long time, if so, it may need to be replaced with a new one.

3. Check the thermocouple.

It may be that the thermocouple can't eat the flame, so you need to adjust the damper under the gas stove to make the fire bigger, so that the thermocouple can eat the flame and accept the heat and then transfer the heat. If it can't catch fire after adjustment, it may be that the thermocouple is broken, and the temperature cannot be sensed, so the gas will be automatically cut off for protection! In this case, you can buy a new one and replace it, which only takes less than 20 yuan to get it.

4. If the above problems are ruled out, then you need to open the stove and check whether there will be a broken connection line between the flame-out protection needle and the solenoid valve caused by backfire, or the nozzle of the damper regulator is blocked.

Situation 2: The ignition is sometimes normal, sometimes it is abnormal.

Generally, this situation occurs mainly because of the pulse ignition micro switch.

Poor contact can be solved by adjusting the pulse ignition micro switch.

Check the battery voltage, make sure that the battery voltage meets the standard, you can confirm by replacing the battery, if the battery voltage is normal, check the battery and the electronic igniter connection, if there is no problem with the connection, it is the ignition failure. Consider replacing the igniter or ignition assembly.

According to my usual experience, if there is no spark when pressed, the battery is dead, and it is good to replace it with a new battery!

It's because the lighter is broken, some time ago, my gas stove also had this kind of failure, just replaced with a new battery, and it doesn't work, you just replace the lighter.

If the gas stove battery has electricity, there is a spark in the lighter, and the place where the lighter head can be wiped clean.

Maybe the battery is low, or maybe there's something wrong with the lighter.

, No, the voltage is too low, but the capacity is sufficient when it can be ignited, it should be that the lighter is broken and cannot produce sparks, so it will not burn.

Of course, the gas stove has a battery, and there is no electronic spark when pressed, otherwise it is very likely that there is no spark because the gas stove has no battery, so there is no spark when pressed, so of course it is okay to replace the battery.

In this case, it is likely that sometimes the air of the same system is blocked, and this kind of thing will happen, or the battery will be dead.

The gas stove has a battery, but there is no electronic spark, and it does not ignite. It could be that the ignition needle is deposited, or the battery is depleted, or the switch is broken.

The gas stove has a battery, but there is no electronic spark, check the metal, whether the contacts are oxidized? Or where there is a break in the line.

When ignition, look at whether the electrode needle has a spark, if not, it is the problem of the lighter, the battery is not charged, the electrode needle connection wire is broken, the battery and the incinerator wire are broken, and the electrode needle is too far away from the furnace cover.

If the battery is leaking, because the electrolyte is a conductor of electricity, it will cause a short circuit in the internal circuit, so it may not spark, which is the most common problem.

You can take the spark apart and clean it. It's where the fire comes out below. It should be clogged up there. Wash it and you're ready to go.

The gas stove has a battery, but there is no electronic spark, otherwise it is very likely that there is no gas, because there is a battery, if there is no electronic spark, there must be no gas.

Although you have a battery, but the battery may still be out of power, you can also charge the battery or replace it with a new battery, what kind of battery is your battery? Disposable?

Hello, happy to answer for you. Reasons why the gas stove can't ignite the fire: first.

First, if there is no gas, if the gas stove does not catch fire, the first thing to check is whether there is still gas, if not, you must add gas. Clause.

Second, whether the battery has electricity, when it is found that it is not on fire, it is necessary to check whether the battery has electricity, if not, you only need to replace the ordinary No. 1 battery. Clause.

3. Poor circuit contact, mainly to check whether the positive and negative poles of the battery box are rusty, whether the line has poor contact, if so, the rust needs to be removed, and the line is accurately connected. Clause.

Fourth, overpressure protection, many gas stoves have overpressure protection function, once the overpressure will not start, then it is necessary to change a pressure reducing valve to try. Clause.

Fifth, the pipeline is blocked, once the pipeline is blocked, it is necessary to check the gas valve, generally speaking, you can smell the smell of coal and the gas stove is not on fire, it is likely to be a gas blockage, then you need to dredge the pipeline. Clause.

Sixth, the micro switch is damaged, the micro switch is a very small place in the gas stove, but it is more difficult to repair than the usual faults, generally speaking, it is not recommended that the owner repair it himself, this is a fine, professional work, it is best to ask a specialist to solve. Clause.

7. The ignition needle is dirty, the kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the gas stove is placed for too long, and the ignition needle is easy to be stained by the oil, so you need to clean the ignition needle and then try to ignite. Clause.

8. The ignition needle is not properly positioned, if you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, once the distance deviates too much, it will cause the gas stove to not ignite, generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it is necessary to aim at the fire hole. Clause.

9. The gas stove has a high-voltage line and its joint, once the high-voltage line is aging, it is easy to make the gas stove can not catch fire, at this time, only need to add a set of high-voltage protection, which should be observed more in ordinary life. Hope it helps you and I wish you happiness and happiness every day! 欄欄

There are three conditions for the gas stove to ignite: gas, electric spark and air, the basic conditions are all there, and the stove is basically no problem, and the reason why it can't be fired can only be that the spark is not in the position of the gas. There are several reasons for this:

The ignition pin is broken, and the spark does not appear at the top of the ignition pin and the center of the outlet. The position of the center is offset from the location of the ignition town, causing the spark to be misplaced. Turn the core and offset the ignition needle, the two top ends are closest to each other, and the spark will not be misaligned, and the center core or core outlet hole is not aligned with the spark position 4

Whether the gas can be burned normally, some gas impurities are also a reason for the difficulty of ignition. You can use a lighter to ignite the gas to test the flammability of the gas. If it is a thermocouple extinguished stove, you need to press and hold the knob for 3-5 seconds after successful ignition, and then extinguish it immediately, ask the official **.

If the gas stove at home does not catch fire, the cause needs to be detected and repaired.

1. See if there is gas.

When the gas stove does not catch fire, the first thing to check is whether there is still gas, if not, add gas.

2. The ignition needle or flame-out protection needle is polluted.

After using the gas stove at ordinary times, the countertop will generally be wiped down, often ignoring the cleaning of the stove, which will cause excessive oil scale accumulation on the ignition needle or flame-out protection needle, affecting the normal ignition, just wipe the ignition needle and flame-out protection needle with a dry towel, and then try to ignite.

3. Check whether the battery has electricity or the battery line is not in good contact.

If there is gas in the gas stove, observe the sparks when the gas stove is ignited, carefully see whether the sparks are weak, and listen to whether the ignition sound is soft and weak, if this is the case, it means that the battery is out of power or the line is not in good contact, you only need to lift the gas stove, replace the battery at the bottom or remove the rust, and connect the line accurately.

Fourth, whether the air pressure is too high.

Many gas stoves are equipped with overpressure protection function, once the gas pressure is too high, the gas stove will not be started, and you need to change a pressure reducing valve to try.

5. Blocked pipes or nozzles.

If there is no problem with the above three points, it depends on whether the pipe or nozzle is blocked. Check the gas outlet valve, if you can smell the smell of gas, it may be blocked, dredge the gas pipeline, then remove the fire distribution cover, use a toothpick or thin iron wire to pass through the nozzle hole, and then put back the fire distribution cover to re-ignite.

It's possible. If the gas stove doesn't catch fire, I think there are two possibilities: one is that the battery is out of power and the battery can be replaced; The second is that the balance is insufficient, resulting in the interruption of gas supply. This can be recharged immediately, wait for 10 minutes, restart the red button of the gas meter, and the gas supply can be restored.

Lack of power is definitely a major reason, and if there is a problem with the circuit, it will not ignite.

Check if there are any high-pressure sparks, and I'm really helping you look forward to it

The gas stove at home doesn't catch fireIt could be because the battery is dead, there may be a problem with the gas stove, or it may be that the gas company has stopped gas.

1. The battery is <> dead

The gas stove at home is newly bought, and it can be used normally yesterday, but it suddenly can't catch fire today, which is suspected to be a dead battery.

Don't worry, just replace it with a battery and try again.

If it is the battery, replace it with a new battery, and the gas stove at home can be ignited normally.

If the gas stove still doesn't catch fire, consider the gas stove to be in trouble.

2. There is a problem with the gas stove <>

The gas stove is newly bought, not because the battery is dead, it is considered that the gas stove is faulty.

If this is the case, it is recommended to find a professional maintenance master, the problem with the gas stove is not a trivial matter, and it must be taken seriously.

There are some gas accidents that are caused by problems with gas stoves.

If the gas stove does not catch fire, or the flame fluctuates, it may be that the gas stove switch is not good, or there is a problem with the gas stove wiring.

In this case, don't use it, and take it for repair immediately.

Families want to buy gas stoves from big brands, quality, my home is a gas stove purchased from a local gas company.

If there is a problem, find them to repair it as soon as possible, and put it into use after repairing, and if it can't be repaired, buy a new gas stove.

3. It may be a <> caused by the gas company's gas outage

You can ask your neighbors if the gas in your neighbor's house is running normally, it is not the gas company's gas outage.

If the neighbor's gas is not running properly, it may be caused by the gas company's gas outage.

If this is the case, there is no need to rush, just wait for the gas company to ventilate.

If you are in a hurry to cook, you can use an induction cooker, rice cooker, etc.

Gas is no trivial matter, if you find hidden dangers, you must solve them in time, otherwise, it is easy to cause a major accident.

Pay attention to safety when using gas, do not leave people at home when using gas, and close the valve in time after using gas.

If you find that there is a gas leak in the room, you should check the valve in time, and ventilate it in time, you can call the gas company and let the staff check it.

Not necessarily, it's probably because there is no gas in the gas stove. This still has to be investigated by a professional.

This is very likely, because the gas stove needs electricity to start the fire, of course, it may be that there is no gas, or it may be that the gas stove is broken, there are many reasons.

Yes, it is very likely that the battery is not charged, so it will not cause a fire, and this kind of gas stove needs to replace the battery regularly.

It has something to do with the battery being out of power, but it may also be because your gas is in arrears, so the gas stove will not catch fire.

It may be because the battery is dead, or there may be no gas, you can look at it according to the gas meter, and you can replace the battery if the battery is dead.

The gas stove does not catch fire, in addition to the battery is dead, which may also be a problem here.

It's entirely possible, but at the same time, you can also ask the property if there is a problem with the gas pipeline.