What does Midea Air Conditioner Display P6 mean?

Midea air conditioning. The reason for the P6 display is that there is an instantaneous large current inside the air conditioner that impacts the inverter module, resulting in the display failure of the inverter module.

Midea air conditioner shows p6 solution:

1. First completely power off the unit, and then re-energize, it will generally return to normal;

2. If the power is cut off and powered on again many times, there is still a fault display, it may be that the internal module of the air conditioner is damaged, and you need to contact the after-sales maintenance department for special maintenance.

Users can check the air conditioner by themselves when the air conditioner displays P6:

1. Check whether the indoor unit, outdoor unit, especially the compressor of the outdoor unit are running normally.

2. Check the air conditioner filter, if the air conditioner can start normally, but the air conditioner cannot be released, it may be that the filter screen is too dusty and needs to be cleaned.

3. Check the refrigerant.

Whether it is insufficient, at this time, check the cold circulation system.

Whether there is an air leak. 4. If the above problems do not exist, the air conditioner is operating normally, check the operation of the air conditioner fan, if the fan air volume is small, it may be that the fan motor is old and needs to be replaced.

Analysis of common faults of Midea air conditioning inverter cabinets.

E1: Whether the compressor current is too high, whether the compressor is overheated, whether the exhaust temperature is too high, whether the module protection, overload protection is short-circuited, and whether the compressor temperature sensor package is short-circuited.

E2: For indoor unit evaporators.

For antifreeze operation, it is necessary to check whether the indoor temperature sensor bag is open, and if so, it can be ruled out.

E3: Short circuit or open circuit of the indoor temperature sensing packet.

E4: Indoor pipeline temperature sensing package open circuit or short circuit.

E5: For indoor and outdoor communication failures, check whether the indoor and outdoor connection lines are wrong (whether the neutral line and belt wire are reversed); Whether the signal line is loosely connected with the control room and connector; whether the controller is damaged, etc.

Air conditioner P6 indicates that the air conditioner inverter module is faulty. It may be that after the air conditioner is turned on, the air conditioner instantly impacts the inverter module of the air conditioner with a large current, which triggers the position protection of the DC inverter compressor of the air conditioner, resulting in P6 fault of the air conditioner**.

Midea's air conditioner inverter cabinet shows that P6 is the position protection of the DC inverter compressor, and it is recommended to shut it down and wait for 5-10 minutes before restarting. Turn off the power on the air conditioner and turn it back on. If there is still one, you can contact the after-sales service.

1. The P6 display is due to the instantaneous impact of the high current on the frequency conversion module, which causes the frequency conversion module to display the fault, and the fixed speed hang-up shows that P6 is a zero-crossing detection fault.

2. Under normal circumstances, the unit will be completely powered off, and then the power will return to normal. If the power is turned off multiple times and the fault is still displayed, the module may be damaged.

1. What does Midea air conditioner display P6 mean 1. Filter reset failure. 2. When the user needs to clean the filter screen, use a toothbrush, fine brush, wet wipe, etc. to clean the air outlet, fan drum impeller, and evaporator dirty parts and then lift the filter screen, remember not to cause damage. 3. After cleaning, the user had better pour a few cups of water along the evaporator, and clean the water tank by the way to prevent the drain pipe from being blocked by residue and dirt, if possible, the plastic drain pipe of the air conditioner can be blown back, and the internal function can hear the sound of air flow or blisters.

2. What should I do if the Midea air conditioner has P6 1, the Midea air conditioner shows P6 failure** is generally due to the instantaneous impact of the high current on the frequency conversion module, resulting in the frequency conversion module display failure;2. In this case, it is recommended to completely disconnect the power supply and remove the plug from the socket, and then power it on and it will generally return to normal. If the power is turned off multiple times and the fault is still displayed, the module may be damaged. 3. The reason why the Midea air conditioner shows P6 is that the outdoor unit environment factors cause poor heat dissipation, so it is recommended to relocate the machine and place the external unit in a different position. 2. The outdoor unit is facing the wrong direction, and it is easy to be exposed to sunlight and cause the outdoor unit to overheat the protection, solution.

Dear, hello, I am very staring at Lu Xing to answer for you: What does it mean that the Midea air conditioner appears P6?Answer: Midea's variable air conditioner screen appears P6 indicates:

The position of the DC inverter compressor is protected, and the temperature thermistor of the outdoor ring is abnormal. The reason why the air conditioner displays P6: the set temperature is too high, and the set temperature in the room will be reached for a while, so the external unit is shut down, and the air conditioner is left with the internal unit blowing, so it doesn't feel cold.

The temperature in the room rises, and the air conditioner starts so it is cold, so it is recommended to turn the temperature lower. 2.It may be that the external unit is too dirty and the heat dissipation is not good, so the compressor is overheated after working for a period of time, and then work after it is cold.

It is recommended to see if the external unit is too dirty, and if it is dirty, it can be flushed with clean water.

Summary. The gearbox shows that P6 is the position protection of the DC inverter compressor, and the fixed-speed hang-up shows that P6 is the zero-crossing detection faultIn case of P6 failure**, it is recommended to shut down and wait for 5-10 minutes before restarting, if the problem is still not solved, you can contact professional maintenance personnel for on-site maintenance. The details are as follows:

1. Midea's air conditioner display P6 fault** is generally due to the instantaneous impact of the high current on the inverter module, resulting in the inverter module display failure;

2. In this case, it is recommended to completely disconnect the power supply and remove the plug from the socket, and then power it on and it will generally return to normal. If the power is turned off multiple times and the fault is still displayed, the module may be damaged.

3. If it cannot be ruled out, it is recommended to find a professional maintenance master for on-site maintenance.

Midea cabinet air conditioner shows what P6 means.

The gearbox shows that P6 is the position of the DC inverter compressor, and the fixed-speed hang-up shows that P6 is a zero-crossing detection fault; In case of P6 failure**, it is recommended to shut down and wait for 5-10 minutes before quietly restarting, if the problem is still not solved, you can contact professional maintenance personnel for on-site maintenance. The introduction of the inverter body is as follows: 1. Midea's air conditioner display P6 fault ** is generally due to the instantaneous impact of the high current on the inverter module, resulting in the inverter module display failure; 2. In this case, it is recommended to completely disconnect the power supply and remove the plug from the socket, and then power it on and it will generally return to normal.

If the power is turned off multiple times and the fault is still displayed, the module may be damaged. 3. If it cannot be ruled out, it is recommended to find a professional maintenance master for on-site maintenance.

The air conditioner of the United States shows P6 fault** is generally due to the instantaneous impact of the high current on the inverter module, resulting in the inverter module display failure; In this case, it is recommended to completely disconnect the power supply and remove the plug from the socket, and then power it back on, and it will generally return to normal. If the power is turned on again after multiple power failures, and the fault is still displayed, it is stupid to fail to tell that the module is damaged; If it cannot be ruled out, it is recommended to find a professional maintenance master to come to the door for maintenance.

Hello, I'm your consultant Zhou Zhou! Sorting out the answers! Please wait a minute!

A blessing, a warmth, with a grateful heart life has been moved everywhere, I hope mine can solve your problem, if my help to you, I hope you move your hands to give me a thumbs up, if you don't solve your problem, please don't worry, ask me directly I will be conscientious to re-answer, and finally wish you a happy life!

Questions. P6 is displayed when it is not turned on

Please wait a moment to ask questions.

It is a fixed frequency 5P ceiling machine air conditioner of Midea.

Hello dear, thank you for your patience, there will be no display in the case of no boot, here to provide you with the beauty of the service**400-889-9315. You can use voice prompts to select the business you are handling, or you can use voice prompts to transfer to manual services.

If there is a problem with the air conditioner itself, you can ask the official to provide door-to-door repair services