How do I remove the excess antifreeze?

Hello, if you add too much antifreeze, you can take out a little from the kettle or disassemble the water pipe to release the point, the coolant is located at the highest scale line, and the replacement cycle is every three years or 60,000 kilometers.

If you add too much antifreeze in the auxiliary kettle, you don't need to pump it in the future. When the car is hot, the excess antifreeze will flow out. This one doesn't need to be smoked, and this one can be completely assured.

You just need to pump out the water in the sub-tank. In fact, if you add 1 more point, there will be no problem. If you want to add 1 more point of antifreeze, but don't lack it, it's a very important place.

If you add a lot of antifreeze to this car, this can be pumped out of the spare kettle.

Hello, there is a lot of antifreeze, you can go to the repair shop to release a little antifreeze, and the repair shop is free to put antifreeze.

Hello, according to the situation you described, this thing basically does not need to be operated by yourself, or you go to the four S store and ask the staff to help you put it down.

All you need to do is open the engine cover and remove the excess antifreeze, so it's recommended to go to a repair shop.

Hello, this is relatively simple, open the auxiliary kettle of antifreeze and directly use the needle to pull out the point.

Hello, this is still relatively simple, open the sub tank cover, and then use the tube to pull it out.

Hello, this operation is very simple, and it can be processed directly at the sub-kettle of the antifreeze.

If there is too much antifreeze in the car, this will not be affected, you don't have to smoke it, just refer to it.

This can be done by going to a repair shop and pumping out the antifreeze with a special pumping machine.

Spraying out must be the high water temperature The reason for the high water temperature: poor heat dissipation and poor circulation.

1. Poor heat dissipation: the fan does not rotate and the water tank is too dirty.

2. Circulation fault: the thermostat is damaged, the waterway is blocked, the antifreeze of the water pump will have a certain pressure when working in the water tank under the action of the water pump, and after the temperature comes up, there is a certain amount of water vapor, if the pressure can not be discharged, the coolant will increase with the pressure of the water pump, so that it is easy to spray out from the water tank filling port, generally the vent on the water tank cover is blocked or damaged, and the water tank cover can be replaced.

The release of antifreeze from the car needs to be realized by disconnecting the return pipe connected between the water tank and the engine, because this position is the lowest, and because the antifreeze of the water tank and the engine can be discharged at the same time, the specific operation steps are as follows:

1. Open the driver's door.

2. Pull the hood switch.

3. Lift the hood of the engine.

4. Slowly unscrew the lid of the small kettle of the water tank and drain the internal high-pressure gas.

5. Disconnect the water pipe between the car water tank and the engine to release the antifreeze.

Boiling the water tank is harmful to the engine:After the water tank is boiled, the engine heat dissipation grinding pants are poor, the temperature is too high, the expansion of the parts will reduce the matching gap of the parts, on the other hand, the temperature is too high and the viscosity of the oil is reduced, in this case, the wear of the parts is aggravated. If not treated immediately, the engine is likely to burn out and cause serious damage.

Introduction to Antifreeze:The full name of antifreeze should be called antifreeze coolant, which means coolant with antifreeze function. Antifreeze prevents coolant from freezing and cracking radiators and freezing engine blocks or covers when the coolant freezes when parking in the cold winter.

Blind demolition. Many people think that antifreeze is only used in winter, but in fact, antifreeze is used all year round. Antifreeze is a kind of coolant containing special additives, mainly used in liquid-cooled engine cooling system, antifreeze has excellent properties such as antifreeze in winter, boiling in summer, waterproof scale and anti-corrosion throughout the year.

Antifreeze generally does not eject out. Too much antifreeze is added, and too much antifreeze is sprayed from the outlet of the auxiliary water tank when the engine is running to normal temperature, and it will not cause any effect. There are a few or two reasons why antifreeze is squirting out of the mouth of the tank.

One: the water tank cover is not covered or the pad is damaged, the antifreeze will be sprayed out from the water tank mouth to make the antifreeze missing, the engine temperature is too high will make the engine seriously worn or damaged, re-cover the water tank cover to replace the damaged water tank cover to supplement the antifreeze has no effect on the engine. Two:

The thermostat is damaged, the water pump is damaged or the fan is damaged, or the water pump belt is loose or falls off, so that the engine temperature is too high, and the dust circle produces an open pot, so that the antifreeze is sprayed out from the water tank mouth and the sub-tank mask, which will make the engine antifreeze seriously missing, and if it is not stopped in time to discharge the fault, it will cause serious wear or damage to the engine. It has a serious impact on the motivation of the hair brother.

Hello Sorry for your problem this easy to cause high temperature of the engine, can not be opened, it is recommended to check the cooling system.

Questions. The instrument display in the car is normal, what is the cause, and whether the coolant can be added directly or something is broken.

What's going on with the car? Suddenly it squirted out.

Questions. Originally normal driving, to the parking lot after parking only to see, the first two days of the battery power loss, put too long, I don't know if it has anything to do with this.

Do you usually maintain the water tank?

Questions. No, I haven't changed it, I want to change the antifreeze or what, the problem inside is quite high by touching it with your hands.

Do not touch and be careful of burns. I think it's a leak in the water tank. Don't say it's squirting. Heng Jing has been for a long time, and the rock has aged. There is also the corrosion caused by not maintaining the water tank.

Questions. Then change the tank? What exactly does it do?

I changed the tank and refilled the antifreeze.

Drive to the repair shop and let the professionals have it overhauled. Or you can see tomorrow if there is any leakage under the car.

Do you have any questions?

I wish you a happy life.

The antifreeze spray of the car is due to the high water temperature, the reasons for the high water temperature: poor heat dissipation, poor circulation; 1. The reason for poor heat dissipation is that the fan does not rotate and the water tank is too dirty; 2. The cause of circulation failure is that the thermostat is damaged and the waterway is blocked; 3. The antifreeze will have a certain pressure in the water tank under the action of the water pump, plus the temperature increases, there is a certain amount of water vapor, if the pressure socks can not be discharged, the coolant will be more and more with the pressure of the water pump, and it is easy to spray out from the water tank filling port.

How is the car antifreeze sprayed out to resist hidden things The car antifreeze spray is due to the high water temperature, the reason for the high water temperature: poor heat dissipation, poor circulation; 1. The reason for poor heat dissipation is that the fan does not rotate and the water tank is too dirty; 2. The cause of circulation failure is that the thermostat is damaged and the waterway is blocked; 3. The antifreeze will have a certain pressure in the water tank under the action of the water pump, and the temperature will increase and there will be a certain amount of water vapor, if the pressure cannot be discharged, the coolant will increase with the pressure of the water pump, and it is easy to spray out from the water tank filling port, and the general situation is that the vent on the water tank cover is damaged, and the water tank cover needs to be replaced.

After the antifreeze sprayed out, Zheng Naxiang came, it became a fog and a finger-shaped, just like the boiling water. At this time, it is generally necessary to consider why the antifreeze is screaming out? Is it a leak of antifreeze or something that needs to be checked?

The release of antifreeze from the car needs to be realized by disconnecting the return pipe connected between the water tank and the engine, because this position is the lowest, and because the antifreeze of the water tank and the engine can be discharged at the same time, the specific operation steps are as follows:

1. Open the driver's door.

2. Pull the hood switch.

3. Lift the hood of the engine.

4. Slowly unscrew the lid of the small kettle of the water tank and drain the internal high-pressure gas.

5. Disconnect the water pipe between the car water tank and the engine to release the antifreeze.

Hello. On the left and right sides of the lowest part of the water tank (the lower rear side), you may have to play it yourself, unscrew the water drain screw before opening the water tank cover, and be especially careful if you replace the final filling, because some vehicles are not easy to operate. Hello dear!

There is a drain screw under the water tank, just open it! 1. Do not add water to the antifreeze. When some riders see a lack of antifreeze in the water tank, they add tap water or "purified water".

There are two hazards in this way: one is to reduce the freezing point of antifreeze, which will freeze the body in severe cold weather; Second, it is easy to cause the water tank to scale and rust, blocking the cold cycle. 2. Pay attention to whether the replaced antifreeze is a fake or shoddy product.

Antifreeze generally has a color, the darker the color, the stronger the antifreeze ability, some black-hearted stores in order to make profits, on the inferior antifreeze to add some pigments, it seems to be concentrated, but after adding to the water tank, due to its cold resistance is not enough, resulting in the large circulation of the cooling system and the thermostat will freeze. This inferior antifreeze must be thoroughly drained from the tank and replaced with a high-quality antifreeze. 3. Don't prepare your own antifreeze.

In order to save money, some riders prepare antifreeze without special measuring cups, thermometers, hydrometers and other measuring tools. If the concentration (specific gravity) of the preparation is too low, its cold resistance is not enough, and it is easy to freeze the water tank and engine; If the concentration (specific gravity) is too high, it will cause the heat dissipation effect of the water tank to be poor, and the engine will overheat. 4. Do not mix two different brands of antifreeze at the same time.

Because the technical standards of antifreeze prepared by different manufacturers are different, if they are mixed together, they will produce chemical reactions in the tank and lose their antifreeze effect. 5. Do not change the antifreeze frequently. In general, the antifreeze should be replaced every two years, and frequent replacement will cause unnecessary waste.

6. If it is not replaced for a long time, the antifreeze ability of the antifreeze will be lost, and it should be replaced on schedule. Before replacement, it is recommended that you go to the franchise stores of Beijing Chinap Auto Care and Beauty Service Headquarters in all parts of the country, use a no-dismantling cleaning machine to thoroughly clean the cooling system, and then add high-quality antifreeze, and if necessary, add a bottle of cooling lubricant, so that the maintenance effect will be better. The drain screw is next to the drain pipe, but when draining the water, it is recommended that you remove the drain pipe so that it is more thoroughly drained, and after the release, it will be cleaner when you start the car Hello, there is a drain hole, but it is not recommended to put it yourself, it is not easy to put it clean.

Hello, the water tank has a drain hole. @2019

Today, the car will give you a brief introduction, how to release the coolant, how to replace the car coolant, do you have a good understanding of the car coolant? I think of automotive coolant as coolant, which is a chemical synthetic agent. The sole purpose is to prevent the engine's cooling system from freezing at low temperatures and then dissipate heat.

Today, I will briefly introduce how to add car refrigerant to my friends, hoping to solve the problem for my friends.

How to add car refrigerant: how to add?

The first step is to do a full inspection of your car to see if there are any cracks and signs of leaks in the pipes. It is best to focus on the bottom bracket, that is, there are five connections connecting various places, which needs to be carefully observed, because the coolant must flow through the bottom pipe and then distribute to different parts of the car in order to function.

The second step, the focus is cleaning, release the previous coolant, clean the liquid channel with clean water, add clean water to the coolant flushing tank, and then inject clean water into the tank, so that the clean water continues to flow through the engine cooling system, and then idle for 3-5 minutes, let the water circulate, the water flowing out of the tank is a little pink, continue to inject clean water until the water flowing out is clean. Don't forget to remove the heating hose and drain the water from the heating tank.

The third step is to replace the coolant with a new one so that the coolant can enter the tank quickly. After about an hour of draining, new coolant can be added from the water pipe of the tank (radiator) and another bucket of coolant can be added to the coolant tank until the coolant tank is almost full, and then the car will be set on fire for 10 minutes. At this point, the liquid level of the cooling system is lowered as some air mass is removed and coolant can then be added.

The liquid level only needs to be within range.

How to add car coolant: How to replace car coolant.

1.Tighten the tank cover, open the tank drain valve, and drain the coolant.

2.Insert a rubber hose connected to the water pipe into the water tank inlet and turn on the tap water so that the tap water continues to flow through the engine cooling system. During the flushing operation, it is necessary to idle the engine and maintain the above operation until the tank drains clean water.

3.Turn off the tap water, and after the water chain in the cooling system is exhausted, the stove closes the drain valve of the water tank.

4.Add coolant from the inlet of the tank to inject the coolant into the tank. Unscrew the reservoir cap, add the coolant, it's time to &ldquomax&rdquo scale mark, be careful not to exceed the &ldquomax&rdquo scale mark.

5.Close the tank lid and reservoir lid and tighten tightly.

6.Start the engine, idle for 2 3 minutes, unscrew the water tank cover. At this point, the coolant level will drop as part of the air body is excluded from the cooling system. At this point, the coolant should be replenished to &ldquomax&rdquo up to the scale mark.

7.Close the water tank lid.

The above is a brief introduction to Bian Xiao Automobile to friends, how to release the coolant, and how to replace the coolant of the car. After reading the profile of Bian Xiao Automobile, friends have the necessary understanding of how to add car coolant! So, do you know a car that your friends don't know?

Millions of car purchase subsidies.