Do you need to hang a sinker for the binding of the fake bait, and do you need to hang a sinker for

ActuallyLuaFake baits do not need to be plumblower.

The plumb sinker is generally added to the main line at a distance of 50 cm from the lure. Different fish are fished with different baits, but if you want to fish for carp with lures, it is recommended to use lure bait.

Since carp is an omnivorous fish, it usually likes to eat earthworms.

The use of this bait can play a good effect, because the carp is a little cunning, the courage is also a little small, the use of lure carp fishing process to master a certain skill, choose lure crucian carp fishing can choose bloodworm or earthworm and so on.

Notes:

Fishing in the shallows or with a fishing rod.

When the bait is hard, there is no need to add a lead sinker, and the fake bait can be thrown to the right position by hand, but the fake bait is light in weight and the throwing distance is relatively far, and it is recommended to add a lead sinker to assist.

The floating lure plus plumb sinker can attack fish on the bottom and reduce the number of times they hang on the bottom.

Just in the fishing tackle shop in the fishing tackle capital Expo City, after the Chinese New Year, go to the lure! I asked the owner of the fishing tackle shop for you! He said the use of the plumb sinker:

Lure lure fishing method soft bait reverse fishing rig is a necessary item, which plays an important role in increasing the throwing distance with counterweight, descending quickly, and affecting the action of soft bait.

Lure is generally used on lure rods, lure is named ** for the transliteration of lure, that is, lure fishing, is a way to imitate weak creatures to trigger big fish attacks, lure bait is a very environmentally friendly fishing method, because whether it is insect bait or commercial bait, are faced with the problem of polluting water quality, and lure bait has greatly reduced this pollution.

Theoretically, lure can catch all aggressive fish, such as blackfish, catfish, catfish, mandarin fish, Mongolian redfish, horsemouth, tilapia, etc., sometimes in the right weather, some of the more wild and docile fish will also attack the lure, such as carp, herring, grass carp, silver carp, carp, etc.

<> lure does not need to be hung with a sinker, which is generally only used to increase the distance of the cast, and can also deal with fish in deep water. To cast the rod, you need to lift it above your head, slightly behind your shoulders, shake it back and forth to judge its inertia and elasticity, and then throw it forward, brake and release the line at 10 o'clock, so that Lua can fly out in parallel, and finally start to reel in the line. Lua should not only understand the use of rods, but also know the habits of various fish, so that he can better attract fish.

Generally, the plumb sinker is installed above the hook, but there are also those that are attached under the hook. The method is to tie the hook, do not cut the excess line, and keep the length of the line 10 15 cm. Then pat the lead sinker and clip it to the extra line.

Fishing is an outdoor sport in which the goal is to catch fish out of the water with fishing gear, and there are no restrictions on gender and age, so adults and children alike enjoy fishing. Fishing is close to nature and cultivates sentiments. There was a long roar near the water, and I thought about the beginning of the decade.

Three Dengjia and B, one into Chengminglu. There are many changes in life, and there are profits and voids in foreign affairs. Today, with Jiangsuo, the sand head sits and fishes.

Before tying the sinker, the line should be passed through the wire hole in the float, and then the float should be pulled to the line to connect it, and the space beans should be installed in a similar way. After that, tie the hook on, and then use your hands to knead the excess part of the line after the hook is loaded into two strands, and tie the lead sinker to these two strands. After tying the lead sinker, you have to wrap the thread around the ** board.

When fishing, the role of the sinker is relatively large. Specifically, a plumb sinker can serve several of the following functions.

1. Adjust the bait: Use the lead sinker to adjust the bait. Using the weight of the sinker itself, the hook can sink to the bottom, so that the bait can stay in the fishing spot all the time, making it easier to attract fish and make it easier for fish to take the bait.

2. Stabilize the hook and bait: In places where the flow speed of the water is relatively fast, the effect of the lead sinker is very obvious. Using the weight of the sinker, the hook and bait can be fixed so that they are not easily washed away by the water.

3. Cast the rod farther: If you want to catch fish in farther waters, you need to use a lead sinker. Only with the help of the weight of the sinker can the rod be thrown further.

In the process of using the plumb sinker, you need to pay attention to the binding method, which can be operated according to the following steps:

1. Connect the fish drift and the fishing line and install the space beans: Before tying the lead sinker, you need to make some preparation tools. The first thing is to connect the float to the line, generally speaking, the line is threaded through the hole in the float, and then the float is pulled to the line.

Then you need to install the space bean, also by passing the space bean through the hole, and then pulling the space bean onto the line, similar to the way you connect the fish float.

2. Hook loading: After the above two steps are completed, the hook should be tied to the fishing line.

3. Tie the plumb: The process of tying the plumb is only after the preparation is completed. First of all, use a suitable size plumb sinker, which cannot be Taichung or too light, and needs to be adjusted according to the specific water conditions.

Some extra lines may appear after the hook is installed, roll these lines in two and secure them with a sinker so that the sinker is tied. After tying, you also need to wrap the thread around the top of the ** plate.

Assemble fishing gear: Good rods, main lines and hooks, and thread a space bean into the main line. Hang the first hook:

Thread the main line through the hole at the end of the hook and hang the hook at the front end of the main line. Hang the plumb pendant: Use the main line to pass through the hole at the end of the plumb sinker and hang the plumb pendant at the front end of the main line.

Hang the second hook: Hang the main line through the hole at the end of the other hook and hang it on the main line to which the sinker is attached. <

1. Assemble fishing gear: First of all, you need to prepare the sea rod, main line and hook. Thread a space bean into the main line and make a coil.

2. Hang the first hook: Then hang the first hook, pass the main line through the hole at the end of the hook, and hang the hook at the front end of the main line.

3. Hang the lead pendant: Then hang the lead pendant, the method is similar, it is also to use the main line to pass through the hole at the end of the lead sinker, and hang the lead pendant at the front end of the main line. After hanging a hook and sinker, you need to be careful not to let them knot together, otherwise they may become knotted.

4. Hang the second hook: Pass the main line through the hole at the end of the other hook and hang it on the main line connected to the lead sinker. It should be noted that the distance between the second hook and the lead sinker is generally about 30 cm, and it is necessary to avoid them getting twisted together.

As mentioned above, when using a sea rod, it is necessary to pay attention to connecting the sea rod to the matching hook and sinker. Then there is the bait, which also needs to be hung on the hook to which the rod is attached. Since it is a double hook, it is necessary to hang the bait on the double hook at the same time.

Generally speaking, the hanging bait is carried out after the drifting is basically completed. If it is an earthworm, bloodworm and other live bait, you can directly take a few and wear it on the hook. If it is pellet bait or self-made grain bait, then it is more convenient to hang the clumpy bait on the hook.

Fishing is inseparable from fishing tackle, fishing tackle can be said to be the core of fishing, the more common fishing line, float, plumb, etc., are basically around the fishing situation to prepare, combined with the object of fish, water conditions, fish conditions and other comprehensive considerations. However, some beginners will find it very difficult to tie the line with the fishing rig, so this article will tell you about the connection methods of these fishing tackles, let's take a look.

Fishing line set to prepare materials.

Start by placing the fishing rod.

Lead skin, lead base, main line, strand line, space beans, fish hook, drift seat, scissors, etc., are all complete, and then placed on the board.

The method of connecting the fishing line group.

1. Tie the rod tip rope: first pull out the rod tip, knot it at the distance of the red rope from the rod tip, and then cut off the excess red rope.

2. Roll lead: the lead skin and lead seat are selected according to the amount of personal use, under normal circumstances, if the float is larger, the greater the amount of lead to eat.

3. The rod tip and the main line are connected: when the rod tip is connected with the main line, in order to prevent it from falling off, you can tie the figure-eight buckle, and after the first figure-of-eight buckle is tied, you can leave a 2cm line distance to play the second figure-eight buckle.

4. Discharge the rod and pay off.

5. After the above-mentioned tied accessories are rolled into a section, they are inserted into the 5th space bean, and then the 6th space bean is inserted into the rolled lead seat, and then the main line is knotted and the figure 8 ring is threaded in. In order to ensure that the length of the line and rod are the same, the excess main line needs to be cut off.

6. The next step is to tie the hook, according to personal needs, take out a section of the strand, tie the second hook at the other end of the strand, and then connect the hook with the figure 8 ring.

The above is a summary of the connection method of lead sinker, float and fishing line, and the length of the main line before the group is tied is best controlled at 10-15cm greater than the length of the entire fishing rod, so as to avoid the phenomenon that the line needs to be cut during production. If the water area is fishing and the fish condition is relatively stable, the line can be relatively shorter.