What should I do if there are fog like spots on the Apple 8p screen?

It may be dusty and needs to be disassembled and cleaned, it is recommended to go to a professional maintenance store.

The fog of the screen belongs to the blurred screen, and the reasons and solutions for the blurry screen are as follows:

1.If the cable is broken, the cable connecting the screen and the motherboard is burned or loosened, so it's good to change the cable.

2.The screen is broken, and the LCD screen is broken, this kind of no way, the most troublesome, to replace the entire screen assembly, the cost is very high.

3.If the motherboard is broken, it is also to replace the entire motherboard, but this probability is relatively small, but it is not ruled out, the way is to replace the motherboard, and the motherboard is generally cheaper than the screen.

Users can get Apple after-sales service to repair, do not find a non-Apple repairer.

Problems with screen appearance.

The phone got into the water.

Is it too cold.? Can I wipe it off?

Put the phone in a broken plastic bag, put a few packets of desiccant, seal it well, and the water mist will be eliminated in a few hours.

Hello, you prepare a pack of cheap dried tea leaves, put your phone in it, and then squeeze out the excess air and tie the mouth of the bag tightly. In general, it takes about two days for the water vapor to disappear. Hope it helps.

If it's summer, just wait two days.

1.Do not try to turn on the device immediately if there is water ingress. Because the iPhone has a built-in battery that cannot be removed, the motherboard will be short-circuited if it gets into the water, and if it is turned on, the motherboard will be burned, causing irreparable consequences.

2.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

3.Wipe the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

4.Send it to a repair center for repair as soon as possible. If the motherboard is severely corroded over time, it will cause irreparable consequences.

What to do if the iPhone gets into the water:

Do not try to turn on the machine immediately after water ingress. Once you try to boot it, it will increase the area burned out by the motherboard by short circuit.

2.Don't shake your iPhone. If you shake your iPhone, water will flow and water may expand inside your iPhone.

3.Clean the water inlet location in order. Quickly remove the SIM card and wipe the water in the iPhone case, dock port, and SIM card slot.

4.Do not turn on the machine immediately after absorbing or wiping off the water.

5.Water ingress can't be turned on, most of them are short-circuited motherboard power supplies, CPUs, hard disks and other chips. The motherboard needs to be repaired.

Turn off the mobile phone and put it in a bag of dried rice or a container full of silica gel desiccant, because it has an adsorption effect, it can adsorb water molecules.

Do not turn it on and bask in the sun for a few hours. Let it cool and see if there is any water mist. If it can't be eliminated, it means that there is a lot of water ingress, it is best to turn on it and use a hair dryer to dry it, and wipe the water traces dry, otherwise it will corrode the internal devices due to the action of current and water vapor.

If there is such a situation in the Apple mobile phone, it may be that the screen assembly is broken and needs to be repaired.

Whether your phone is flooded, if it is flooded, the hardware of the screen is eroded, this will happen, or your screen is not the original screen.

There is a problem with the screen display.

It could be that the screen is broken.

Go to the official after-sales inspection and repair.

It is recommended to go to the after-sales service to do a test to see if you need to return to the factory for processing!

How long does this take to produce a lot of noise?

It should be a problem with the display, and if you mind this, take it for repair.

It may be that there is a problem with your screen, take it to the mobile phone store to test it.

In the application, it is two-finger magnification, if it is to enlarge the screen, you can go to Settings - General - Accessibility - Zoom to turn on only Chunran, press twice with three fingers to shrink the forest, move the screen with three fingers to drag, you look at it, but the resolution will be lower after zooming.

Answer: The main is engaged in mobile phone repair, because the screen has a lot of layering is more complicated, generally there is no way to deal with it by yourself without a machine, the water is generally backlight and water, you can go to a nearby mobile phone store to repair the machine There are generally machines that can be heated and dried, and it is also possible that the maintenance master wants you to change the backlight.

1. Do not move or shake the phone frequently after entering the water, so as to avoid the spread of moisture inside the phone.

2. Do not bake with a hair dryer or stove after entering the water, so as to avoid the liquid being blown into the inside of the mobile phone and damaging the mobile phone at high temperature.

3. Some mobile phones can be turned on and used normally after simple processing, but the mobile phone is composed of precision electronic components, and there is a hidden risk after water ingress, so it is recommended not to try to turn it on.

4. It is recommended to bring your mobile phone to the regular Apple customer service center for inspection and maintenance.

The water ingress of the iPhone is not very serious, but the screen has a water mist The method of suction is as follows:1I cover iphone with rice in a sealed, dry environment for around 2-3 days 2

If the hot air dryer is still within the warranty period, it is recommended to make an appointment for maintenance through Apple's official website: 1After logging in to Apple's official website, click on "Technical Support"2

Click "Provide Serial Number", enter the correct machine serial number, and inquire about the warranty period to make an appointment3After the appointment is successful, bring the machine and ID card to the Apple store for repair within the specified date.

Determine whether it is a bright spot or a bad spot.

The dead pixel is a screen problem, and you can't get it. Bright spots refer to the brightness difference of local small spots on the white background, and Nashan is basically invisible in other backgrounds, which is generally a problem with the backlight plate and has nothing to do with the screen.

You can try to wrap it in paper and stuff it into a desiccant bag and seal it for 24 hours after shutting it down. If it doesn't work, you can only send it for repair.