How to add ink to HP printers, how to add ink to HP printers

To refill an HP printer, simply place a new ink cartridge directly into the printer, and the specific operation steps are as follows:

System: EMUI

Computer: Huawei MateBook

System: Windows 10

Software: HP DJ 2330 Printer.

1. Tear off the plastic seal.

Prepare the ink cartridges of two HP printers directly, and gently tear off the plastic seal of the outermost layer of the ink cartridge.

2. Put in the new ink cartridge.

Then open the lid of the ink cartridge of the HP printer, face the chip of the ink cartridge prepared by the master, and then place the ink cartridge inside the printer.

3. Close the lid.

Put the lid on the printer so that your HP printer is ready to use.

HP Printer Ink Method:Preparation materials: two ink cartridges, HP DJ 2330 printer.

1. Tear open the plastic seal: Directly prepare the ink cartridges of two HP printers, and gently tear the plastic seal of the outermost layer of the ink cartridge.

2. Put in the ink cartridge: Open the lid of the ink cartridge of the HP printer, face the prepared ink cartridge chip inward, and then place the ink cartridge inside the printer.

3. Close the lid: Put the lid on the printer after putting it away, so that your HP printer can be used normally.

Here's how to add ink to HP printers:1. Pull the lid on the printer open, and then gently take the ink cartridge out of the printer.

2. Put a layer of label on the top of the ink cartridge, gently tear it off by hand and put it aside.

3. Open the lid of the ink tank, and then use a syringe to draw an appropriate amount of ink.

4. Slowly inject the ink in the syringe into the hole of the printer cartridge, the process must be slow, and wipe the cartridge dry with a paper towel after injection.

5. After the injection is completed, paste the cartridge label back to its original place, let it stand for 10 minutes, and then put it back into the printer after standing.

The HP printer refueling tutorial is as follows:Device: HP printer.

Material: HP Specialty Ink.

1. First of all, you need to take out the ink tank of the printer.

2. Press and hold the green button on the left side to detach the operation.

3. Shake the newly bought ink a few times.

4. Then remove the yellow plastic cover.

5. Press it gently until the green card on the left side is ready.

6. After installation, close the front cover for system detection, after the detection is successfully completed, the green light of the printer [ready] will turn on. The installation is complete and ready to use.

1. First of all, the first step is to use the ink sink window to visually check the ink level of the printer.

2. The next step is to open the cartridge lid.

3. Then you need to remove the plug on the cartridge that is being filled. Note that at this time the stopper should be placed upside down on a piece of waste paper.

4. The next step is to press and hold the nozzle on the ink cartridge, gently push down, and then let the ink flow into the ink cartridge. Fill the cartridge to just below the lowest fill line on the cartridge.

5. Finally, after filling the ink cartridge, pull up the ink bottle vertically. Hold the cartridge upright, then push the cartridge plug into the slot on the cartridge and close the cartridge lid.

HP printer cartridge refill method:

1. First add the printer points. Then open the lid cartridge and automatically move to a position that is easy to remove. Then press down to remove the cartridge. (The specific way to take it out may be related to the printer, so you can refer to the printer manual).

2. In this example, there are two demonstration ink cartridges, one is a black original ink cartridge (without ink filling holes) and the other is a 3-color color ink cartridge (with 3 ink filling holes). If the black ink is insufficient, the black ink is taken, and the corresponding color ink is not enough to take the color ink cartridge. (Places cannot be exchanged) here are explained by taking them off.

3. When taking the ink cartridge, prepare a clean piece of paper and put the ink cartridge on it.

4. There is a piece of adhesive tape attached to the top of each ink cartridge, and there will be a hole for injecting ink under the general adhesive tape. Just tear it lightly and you can see it (don't throw it away when you tear it off, refill it with adhesive tape after refilling it).

5. The purchased ink generally has a more convenient pointed mouth for adding ink, and be careful to add ink once squeezed into too much. Because bubbles will be generated. In this way, you can add it gradually.

After adding ink, it is recommended to seal the hole with tape. This prevents ink from spilling and dust from drifting in. (Generally, when adding the amount of ink, it is recommended that the ink bottle look like two or three grids, depending on the size of the ink bottle, it will be explained).

6. The original cartridge does not have an ink hole. But you can see a concave dot, which can be used to open the ink hole by itself. You need to carefully make an opening with a knife yourself. Do not let the plastic fall into the process of opening, and add ink according to the above after opening.

7. If the printing ink is light after adding ink, the effect of cleaning the print head in the settings (not washing it yourself, but in the settings of the printer driver) will be improved.

Here's how to add ink to HP printer cartridges:

Tools Raw materials: Shenzhou God of War K670D-G4D1, windows10, HP printer, ink.

1. Turn off the power of the printer, we open the side cover, take out the ink cartridge below, and lay it flat on the desktop to prevent the rest from spilling.

2. Take out the ink, open the rubber stopper on the ink cartridge, inject the ink into the ink cartridge through the pointed nozzle on the ink bottle, and do not use too much force when adding ink to prevent the ink from overflowing.

3. When the ink is almost full, stop adding ink, put the ink bottle aside, wipe off the spilled ink around the ink cartridge, and put the ink cartridge back in its original position.

4. Put A4 paper on the printer, turn on the power switch, and you can directly use the printer to print.

The HP printer refueling tutorial is as follows:Device: HP Printer SO550.

Material: HP Specialty Ink.

1. First of all, you need to take out the ink tank of the printer.

2. Press and hold the green button on the left side to detach the operation.

3. Shake the newly bought ink a few times.

4. Then take off the yellow plastic lid and take off the tasseled shirt.

5. Press it gently until the green card on the left side is good.

6. After installation, close the front cover and carry out system testing, after the detection is successfully completed, the green light of the printer [Ready Spring Chain] will light up. The installation is complete and ready to use.