How to knot the rope of the pendant How to knot the rope of the pendant

After burning the end of the rope with a rope, the rope is finely pinched, and then the rope is pierced through the pendant and left the appropriate length of binding according to personal preference. After that, open the top of the rope and wrap the rope around the other side to tie the knot.

1. It is preferred to burn the thread with a lighter.

2.After burning the thread, thread the thread through the hole in the pendant.

3.After passing through the small hole, leave a little distance from the roots, about 1cm, and wait for backup.

4.Pull the thread back and hold it with your fingers.

5.Then wrap the thread around the thread at the other end, and make each circle parallel when winding, not overlapping, it will not look good if it overlaps.

6.The length of the circle is about 4-5 turns, and the length of the reference line can determine the number of turns. After wrapping it, thread another thread through the small hole in it.

7.Then tighten the other line underneath.

8.Once tightened, the knot shape of the threading comes out.

1. Prepare the pendant, braided rope and other materials, pass the rope through the pendant, and then knot the rope.

2. Hold the rope of the pendant in one circle in your hand, and then wrap the other end of the rope around your fingers twice.

3. After that, take off the rope on your fingers, thread the rope into the two loops and tighten it, and then tie a knot to fix it, and then the knot will be tied.

4. The method of another knot is the same, tie the rope in a circle, wrap the rope head in the loop twice, and then tighten it and tie a knot.

5. At this time, the rope of the pendant is knotted, and the length of the rope can be adjusted freely.

1. First prepare two red threads, pendants, lighters, scissors, etc., align the two red threads, then fold them in half, find the center point, put your thumb in the center, and then start to weave the diamond knot, after braiding the five diamond knots, wear the prepared pendant with one thread, and then weave the five diamond knots on the other side equally.

2. Leave a little distance, start to weave four diamond knots on each side, the distance from the first cavity and become larger at a time, and then weave three, pay attention to the symmetry on both sides.

3. After completing the above steps, prepare a thread of eight centimeters of seven traces, put the four threads on both sides of the braided necklace rope together, and put the thread below to weave a flat knot.

4. Braided 5 to 6 flat knots, use scissors to subtract the excess thread, but leave a little thread, and then burn the thread with a lighter. Finally, glue the beads and you're done.

5. Roast the rope over fire and pinch it while it is hot so that it can pass through the hole. The ends of the rope are passed through the pendant hole together, depending on the individual leaving the appropriate length of the tie such as 1cm.

6. Then open the end of the rope, tie a knot around the other side, tie a knot around the other side, and tie the knot in reverse again, so that the knot is tied in front and backward until the length of the rope head is left, and the end is treated with a lighter.

About the rope knotting method Daquan ** pendant is as follows:

Use a lighter prepared in advance to ignite the ends of the threads used for piercing the pendant rope, and quickly twist it into a thin wire by hand (see the figure, pay attention here to prevent burning your hands), and then use scissors to cut off the excess and irregular part of the rope end.

Pierce the pendant rope through the front of the pendant, and then pay attention to keep a distance of about 1 cm between the pendant hole and the top of the rope (you can reserve the length according to your actual needs).

Face up the pendant, separate the pendant rope, tie the No. 1 rope and the No. 2 rope to each other, and gently pull the two ends of the rope tightly, as shown in the small picture in the lower left corner of the picture. Turn the pendant over, back side up, tie the knot according to the way in step 3, and gently pull the rope tight, as shown in the small picture in the lower right corner of the picture.

Pendant face up, repeat knotting as in steps 3-4. After repeating the steps more than three times, you can get the appearance of the pendant knotting method in Figure 6. At this time, you can choose not to continue tying the knot.

After the pendant knotting is completed, the excess rope end is quickly cut off with scissors to ensure that it is neat after cutting, mainly do not cut too much or too little (reserve about 1-2 mm).

Then use a lighter to light the rope port and press the flat rope port. At this point, this pendant rope weaving method is completed, how about it, it's very simple, you can try it too! First of all, you need to untie the slipknot at the end of the jade bead chain.

The knotting method of the pendant rope is as follows:

Tools Raw materials: pendants, ropes, crochet hooks.

1. Prepare 1 pendant and rope in advance.

2. Thread the small hole of the pendant rope pendant, if it is not easy to wear, you can use crochet to assist.

3. Thread the other end of the rope through the loop.

4. After passing through, twist the upper ring and turn it around.

5. Thread the other end of the rope through the new loop.

6. Tighten the hanging rope hard, and the pendant will complete the knotting.

The pendant is generally a special shape of the main body, but after the collapse is connected with a rope or metal chain, the rope is not easy to hurt the neck, but it is easy to break after a long time.

Metal rope is better made of stainless steel or silver, both of which are not very good, especially for Europeans and Americans! However, the metal is hard, if the process is not good, it is easy to hurt the neck, so friends should pay special attention when purchasing!

A common knot method for braiding pendant lanyards is to prepare a separate key and a rope, thread the rope through the key, and then align the ends of the rope and place the key in the middle of the rope.

In addition to this, there are:

Step 1: After the rope is stretched, first turn the left rope backwards to form a circle, and the right side does the same to form a circle, and the left and right rope loops should be made the same size. Bring the two circles together, and press the right one against the left.

Step 2: Cross the two ropes, wrap the rope head around the rope in reverse twice, and then tighten the rope head through the two rope loops, the right side is done, and the left side is also done in the same way. The knot is a fisherman's knot, also known as a telescopic knot.

The common knotting method used in the second braided pendant lanyard is as follows:

Step 1: First burn the two threads, rub them into a sharp shape with your hands, and pass the two ropes through the jade.

Step 2: Then put the jade stone at the bottom, separate the two ropes, and loop the rope on the right into a circle.

Step 3, then the left rope through the circle, tighten and tie into a knot, and repeat the operation left and right in turn.

Step 4: Finally, remove the excess rope, leave 1-2 cm of thread, and finally burn the thread with a lighter.

The third method is as follows:

1. Roast the rope and pinch it while it is hot, so that it can pass through the hole, and the rope end will pass through the pendant pendant hole together.

2. Depending on personal preference, leave an appropriate length of lashing length, such as 1cm.

3. Open the end of the rope, tie a knot around the other side, tie a knot around the other side, and tie the knot in reverse again.

4. Tie the knot until the length of the rope head is left, and the end is treated with a lighter.