What is the quality of Delta s power supply and where is Delta power supply made in China?

Updated on technology 2024-08-04
5 answers
  1. Anonymous users2024-02-15

    1.Delta's power supply is of good quality, both in terms of service life and materials. The quality of industrial power supply or DC power supply is very high;

    2.Delta started as a power supply; You can look at the power adapters on the laptop, most of them are made by Delta.

  2. Anonymous users2024-02-14

    Delta mainly started as a power supply, relatively speaking, the quality is good, if it is a quality problem within a year, it is a new machine, Delta tablet switching power supply 24V 100W PMT-24V100W1AA inventory 267 60 pcs.

    Delta Tablet Switching Power Supply 24V 150W PMT-24V150W2BA 70pcs 359pcs in stock.

    Delta Tablet Switching Power Supply 12V 150W PMT-12V150W1AA 1pcs 76pcs in stock.

    Delta Tablet Switching Power Supply 24V 100W PMT-24V100W2BA 6pcs 58pcs in stock.

    Delta Tablet Switching Power Supply 24V 200W PMT-24V200W1AM 2pcs 107pcs in stock.

    Delta Tablet Switching Power Supply 24V 350W PMT-24V350W1AG 442pcs 123pcs in stock.

    Delta Tablet Switching Power Supply 24V 100W PMT-D1V100W1AA 2pcs 89pcs in stock.

    Contact: 1 5 8 1 4 1 0 7 6 6 3

  3. Anonymous users2024-02-13

    The brand is Taiwanese, and the manufacturing place looks at the box.

  4. Anonymous users2024-02-12

    Delta's Wujiang plant also produces power supplies.

  5. Anonymous users2024-02-11

    The rated power is good to be sufficient, if it is small, it is not enough, and if it is too large, it is a waste.

    1. Use Master Lu to calculate the amount of power required by the host. On the computer with "Master Lu", open Master Lu, click "Power Consumption Estimate" on the left side of the main interface, open the "Power Calculator", and fill in all the hardware of your computer host in the power consumption table, that is, to display the wattage of each hardware and the power consumption of the whole machine, such as 100W.

    2. The sum of the power consumption of each hardware of the computer is 100W, and the insurance coefficient should be increased by 10-20%, plus 10%, 100W+100W 10%=110W.

    3. The power supply is the power of the power supply, and the load power is best controlled at 60-80% of the rated power of the power supply. The control rate is calculated as 70%, 110w 70%.

    4. The power supply used by this computer is good. If you consider the need to upgrade the computer hardware in the future, you can choose a power supply with a higher rated power.

    How much power you use in your hand, refer to what I said above.

Related questions
5 answers2024-08-04

Working at Delta Electronics Factory, I recently learned about the real life of the workers at Delta Electronics Factory. Their lives can be described in one word - miserable. The factory completely disregarded the lives and deaths of the workers. >>>More

7 answers2024-08-04

For switching ripple, it must exist both theoretically and practically. There are five practices that usually suppress or reduce it: >>>More

17 answers2024-08-04

Kingdom ATX-350&P4 Standard Edition uses a dedicated power supply for P4 with a rated power of 350W. >>>More

2 answers2024-08-04

The lines of "Avatar 2" are as follows:

1. Your soul will be with Eva, and your body will remain here and become a part of us. >>>More

30 answers2024-08-04

This has a small point of complexity, after turning on the 220 volt power supply, use the multimeter DC gear to detect the small 24 feet, find the 3 volt or so line should have several all marked out, and then use Feng Ming to find the iron foot from the 24 small feet, turn on the table will call, and then use the 3 volt foot line detected before to connect the iron foot, any that tie can be, the 3 volt line one by one check, know that the fan rotates, this line is the start line, At this time, the line on the high-current foot is not any voltage, in the remaining 3-volt wire to contact the lap iron leg one by one test, know that the voltage on the high-current foot, the 3-volt line can touch any lap foot, but can not touch the 12-volt foot after the fan rotates, otherwise the power supply is broken, remember to remember.