How to deal with the seams between the hollow core slabs of the new house?

Updated on home 2024-08-01
5 answers
  1. Anonymous users2024-02-15

    First, the original filling between the gaps of the hollow slab is cleaned up, and then the installed middle seam is re-cut with a special sewing machine to minimize the gap width difference between the plates, and then fill it with marble glue close to the color of the plate. It is required to be close enough to the color of the original panel.

    Fill the adjusted marble glue again, because there will be a certain degree of shrinkage after the marble glue is completely solidified, so the marble glue should be slightly higher than the level of the plate, so that it will not be filled many times.

    The grinding and polishing sheet and grinding filler are used to make it a horizontal plane with the hollow core plate, which increases the overall feeling, solves the problem of high and low position between the gaps, and prevents the gaps from returning to black again.

    With the special cutting grinding disc, the cutting position is carefully polished, so that it becomes a flat whole with the plate.

    The hollow plate crystallization powder and crystallizer are used to polish with the crystal surface grinder, and the plate and the crystallization powder are subjected to a physical and chemical comprehensive reaction under the action of high temperature under the heavy pressure of grinding to form a dense and hard crystalline protective layer.

  2. Anonymous users2024-02-14

    It is not possible to lay a brick wall on a prefabricated hollow core slab, there is no beam bracket underneath, you can consider a lightweight board or infill wall, which is lighter in weight. It can be raised 40 cm, and the drainage pipe goes to the outer wall, pay attention to waterproofingwith a water repellent agent.

    First use waterproofing agent mixed with cement mortar to do it at the base of the bathroom, and after it is dry, then use waterproofing agent mixed with cement ash to brush a layer on the surface of the first time. With the coil, first clean the base layer and dry the base layer, then spread the coil on the ground, and heat the coil with a spray gun, which is the gap bonding between the coil and the coil. However, the membrane is relatively fragile, and the surface is easy to be broken by the stones when backfilling, resulting in water leakage.

    Non-woven fabric, which is similar to cloth, after brushing the base layer with cement mortar thinly, it can be directly spread on it.

  3. Anonymous users2024-02-13

    The joints between the hollow slabs, filled with fine stone concrete, are tamped. The wide seam should be reinforced and the template should be hung below. Very fine seams, the stones can't go down, and they are filled with cement mortar.

  4. Anonymous users2024-02-12

    How to deal with the difference in the plate seam when the hollow core slab is laid? Please give specific steps [[can be dealt with or not dealt with depending on the situation]].

    When the slab gap is large, it is necessary to add steel bars to make fine stone concrete [method In fact, at the joint, the concrete should be poured to create a small beam of I-section along the long direction of the hollow slab, and the trabecular also has a role that is to connect the two hollow slabs into a whole Propolis boiled more and then connected into a piece into an overall version of the windy early summer, not only the formwork, you can use the hanging mold process construction This method The construction progress is fast and the follow-up construction is not like cast-in-place concrete to wait for the strength of the concrete Disadvantages The seismic performance is slightly poor].

  5. Anonymous users2024-02-11

    Is it a prefabricated hollow core slab? When the slab joint difference is large, steel bars should be added to make fine stone concrete.

Related questions
7 answers2024-08-01

I think tile grout, just listen to the name, everyone should know what this thing is, right? As a material that fills the gap between tiles and tiles, although it is only a few millimeters wide, it plays an important role in landscaping. So, what is the color choice of tile grout? >>>More

25 answers2024-08-01

Ignore anything other than work, try not to express affection, and talk in a serious tone to reduce misunderstandings.

12 answers2024-08-01

Whatever you want, there will be such a thing happening when you go to ** to do things, and anyone will talk nonsense behind your back, in fact, sometimes you will say that other people's are not behind your back, so you should be retribution! Even if you know who is not, you must pretend that she is a no-nonsense person in front of him, and treat her with a smile on her face, and the relationship will not be so stiff! It's the same with business, no matter how the guest is not, how difficult you have to get along with, at most after you go back, you keep talking about how he and how she is, anyway, she won't know!

14 answers2024-08-01

1. The only way to do it with A and not want to offend B is to do some projects that B's girlfriend doesn't understand, can't do and doesn't want to do, so that B's girlfriend feels that they are not guaranteed and doesn't want to be with you. Remember, when you are alone with B, you should say that it is not your personal idea, but you can't explicitly say that it is A's idea, leaving room for him to guess. Because there is no father and son on the battlefield, there is no need to show mercy, and if you can't be a partner at this stage, you can still be a friend, and it will be difficult to say the opposite in the future. >>>More

26 answers2024-08-01

Husband and wife should understand each other, help each other, accompany him more when the other party is unhappy, and accompany him to find a way when the other party is in trouble. >>>More