Tiffany watches designated after sales service center

Hello, happy to answer this question for you.

What should I do if my Tiffany watch gets into water? This should be the first question many people want to ask after accidentally getting water in their watches. The emergency self-rescue method after the watch enters the water, and it will be used when it is collected.

The waterproof of the watch depends on the waterproof rubber ring on the glass, back cover, handle, etc. to meet the corresponding standards. All waterproof watches are stamped with the words "waterresistant" or "waterproof" on the case back. Watches without waterproof markings are only protected from dust and should be protected from water.

A simple way to deal with water after the watch has entered the water:

Method 1: If an ordinary mechanical watch is damp, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at a distance of about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the moisture in the watch can be dissipated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method 2: Put the mask facing inwards and the chassis facing outward, and wear it on the wrist, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to send it to the watch shop immediately to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method 3: Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Note: When not wearing it, try not to let the watch get wet, so as not to deform the leather; Placing it near magnetic objects can also affect the accuracy of the watch. In addition, even water-resistant watches should not be immersed in water, and it is best to check them frequently whenever the watch has been blistered (unless it is a diver's watch) to avoid serious damage to the internal movement parts due to time delays.

In fact, the degree of waterproofness of the waterproof watch will change as the waterproof ring hardens, so it is necessary to replace it in a timely manner. In hot and humid weather, it is easy to condense the oil inside the watch, resulting in the phenomenon of stopping, slow or completely stopping, and will cause the hardening of the waterproof ring and reduce the waterproof function. It is particularly important to note that seawater contains salts and is corrosive to metal components, so the watch case should also be rinsed with fresh water after outdoor activities to avoid corrosion.

You must know that a man's watch is often thousands or even tens of thousands, and if it accidentally gets into the water, then the watch may be ruined. If you are also a watch lover, take good care of your watch from life, try not to let your watch come into contact with water, in case of water, but also pay attention to timely maintenance!

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

Water ingress into the watch is most likely caused by prolonged exposure to water during use. Water ingress into a mechanical watch is very serious. In mild cases, the oil of the watch may melt away, and in severe cases, the watch parts will be corroded.

Once the user finds that the watch is flooded, he should send the watch to [8th Floor, 8th Floor, Block E1, East 1st Office Building, No. 1 East Chang'an Street, Wangfujing] for maintenance.

Water ingress into the watch is a common fault of the watch, and it is also a very harmful failure.

Water ingress of the watch may cause rust on the internal movement parts of the watch, although the watch parts are now treated with anti-rust, but some tiny parts are still easy to rust, so it is better to repair the watch as soon as possible once the watch is flooded.

If other liquids are introduced, such as seawater, which are more corrosive, then the corrosion will also be faster.

Generally, the light bulb on the Internet, the sun is scorching, the watch is dried by body temperature, hair dryer, desiccant and other methods are not advisable and unsafe, if the value of the watch is higher, it is better not to take risks.

If you have any questions, please call**, please feel free to answer.

Tianjin Tiffany after-sales maintenance center address is in Tianjin Heping District Chifeng Road No. 136 Tianjin International Financial Center 30th Floor Room 3003, the service center accepts national mailing service, if there is mail, please contact the center in the mail. You can call 022-27122725 for more information.

Method 1: Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear. This method does not damage the timekeeping and components of the watch;

Method 2: Lamp baking method: Wrap the watch in water with a paper towel, put it at about 15 cm near a 40-watt light bulb, and bake for about 30 minutes. Never roast over fire;

Method 3: Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the moisture can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Generally speaking, there are only three places where water can enter the watch movement: the handle (handle), the Bipure watch and the back cover. The waterproof device is also installed in these three places: add a rubber ring to the shank, add a rubber ring on the threaded edge of the back cover of the sealing ring, shank and other parts, and make the surface tight.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If it is not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, resulting in inaccurate timekeeping and watch failure.

If the watch is seriously flooded, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage.

1. If the water ingress of the watch is serious, it is best to send it to the watch store to wipe the oil and eliminate the water in the watch to avoid rust in the watch parts.

2. In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot steam, and pay more attention not to be exposed to rain on rainy days.

3. Bake with an incandescent lamp, wrap the watch with several layers of paper towels, and then sell it in bulk and put it at 15 cm of a 40-watt incandescent lamp, bake for 5 minutes, and the water vapor in the watch can be evaporated. It is important to remember that the lead sedan should not be baked for too long, and the strap should be removed first for watches with leather straps.

4. When the watch is flooded, it is best to go to a regular watch repair center or after-sales service as soon as possible. The faster it is processed, the smaller the loss. Because although most of the watch movement substrates and bridges are nickel-plated and rhodium-plated, the surface of some steel parts is still not treated with anti-rust, once rusted, a loose rust layer is formed on the surface to continue to absorb water and accelerate rust.

The strap is the most important part of the watch, and a broken buckle spring means that the watch cannot be disclosed. At this time, you have to go to a professional shop to repair it or take a look at the tutorial below and do it yourself.

Where the strap is in the form of a butterfly clasp, there are also two types:

1. When opened, it looks like a "stiff pull".

2. There is a snap button, which needs to be opened by pinching it without fingers in the hand cavity.

Butterfly buckle straps with snap buckles can be easily opened for two reasons:

1. The snap buckle is too long and too protruding.

2. The other is that the spring inside it is too soft.

The maintenance service center is located at: [Room 05, 24th Floor, SAC Sichuan Aviation Plaza, No. 6 Renmin East Road, Jinjiang District, Chengdu, Tel: 028-62780618].

If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a height of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

If the water ingress is severe, it is best to immediately send the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the hand parts of the Zero Spring.

On the 11th floor of Block D, Central World Trade Center, No. 6 Jianwai Street, Chaoyang District, Beijing, there is a place for Tiffany watch after-sales maintenance.

Tiffany watch magnetization solution:

1.The demagnetization of a watch theoretically places the watch in a strong alternating magnetic field, and the intensity also decays gradually. Usually, a large hollow coil is used, an alternating current is applied, the watch is placed in the hollow coil, and then slowly withdrawn, which is equivalent to gradually reducing the strength of the magnetic field.

This action has to be repeated many times, and each time the watch must be changed by 90 degrees, because the demagnetization effect is best when the magnetic field lines of the demagnetized magnetic field and the magnetic field lines of the demagnetized watch are in the same direction, and when they are at an angle of 90 degrees, they are invalid. Therefore, it is necessary to demagnetize the watch in all directions before it can be cleaned.

2.The professional demagnetization equipment uses a C-type silicon steel core with two sets of coils to discharge with a large capacitor to produce an alternating magnetic field with attenuation. The watch is placed in the groove of the demagnetizer, press the button, the neon lamp flashes to complete the demagnetization instantly, of course, the watch also needs to change several directions and repeat the demagnetization process.

3.To demagnetize the watch in a simple way, it is to find a transformer (the power should be sufficient) or something, and it is also to gradually move the watch closer to their core, and then gradually leave; Change the angle or the direction of the watch and repeat this action constantly, but this method does not guarantee that the watch will be demagnetized. Demagnetization should also be a necessary procedure for watch maintenance, and the accuracy of the watch should be corrected after it is completely demagnetized.

First, when the watch enters water and fog, the easiest way is to wear the watch on the wrist, that is, let the watch reflect inwards and the bottom case of the watch outward. After a few hours, you will notice that there is less and less moisture inside the watch.

Second, prepare some paper towels or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. After that, you will notice that the moisture in the movement slowly disappears.

Thirdly, fog vapor can also be removed by basking in the sun. First open the back cover of the watch, then wrap the watch completely with a paper towel or moisture-absorbing flannel cloth, and take it to the sun for most of the day to remove the moisture in the movement.

Fourth, after the watch is flooded, you can first open the back cover of the watch, remove the battery, and use the hair dryer to aim at the watch on low gear. After blowing until it is completely dry, reattach the back cover. When installing, you can also check whether the sealing ring is aging and broken, and remember that the back cover must be fastened if it is in good condition.

Fifth, dry the granules with silica gel. Put the silicone granular substance in a closed container with the watch that has accumulated water, and after a few hours, remove the watch and the water will disappear.

Neve after-sales service center is located on the 11th floor of Block D, Central World Trade Center, No. 6, Jianguomenwai Street, Chaoyang District, Beijing

What are the factors of dust in watches? Under normal conditions, the sealing of the watch is very high, what are the factors that cause the watch to be dusted? In addition to artificially disassembling the back cover of the watch at will, there are two main factors for the watch to enter the dust.

First, you should mainly check whether your watch is tight, whether it is cracked due to aging or loose with the case (ring). Due to the poor closure of the watch, it is generally water when the ash enters. The second factor is due to internal wear and tear, since the ash on the dial does not come from the outside.

How do I clean my watch after it gets dust? After finding that the watch is dusty, do not easily disassemble the back cover for cleaning, and send it to the after-sales service and other professional places for cleaning in time, and do the waterproof test and the accuracy test on time to ensure its normal operation. At the same time, we should also pay attention to the fact that our watches do not come into contact with chemicals in our daily lives.

The waterproof watch is not cold water, so don't wear it to take a bath, to prevent water vapor, to ensure its waterproof effect, and then after adjusting the watch, remember to restore the watch handle, press it tightly, to avoid dust in.