What should I do if the water glass and plastic fake flowers are not sticky?

Updated on home 2024-08-15
10 answers
  1. Anonymous users2024-02-16

    What should I do if the water glass and plastic fake flowers are not sticky? PBT can not be bonded with epoxy resin, it is an inert surface like PP, the correct resin for grafting should be PA or CPP (polyamide, chlorinated polypropylene), PBT should be primed with silane coupling agent, then adhesion promotion layer, and finally glued to other workpieces you want to bond. Epoxy resins can only bond non-olefin plastics.

    Before bonding, do a good job of surface grease removal, it is recommended to use generally not directly added to the epoxy resin component, adding to the epoxy resin component will shorten the storage period, the most common phenomenon is to add E51 epoxy resin to cause E51 epoxy resin to slowly become opaque, crystallized, agglomerate.

  2. Anonymous users2024-02-15

    The landlord's title is also weird and funny, what should I do if it doesn't stick or not? Non-sticky of course not sticky, hehe. Solution within:

    1. Roast it over a holding fire.

    2. Brush the bottle with alcohol and stick it again, but quickly.

    3. Soak it in banana water before sticking.

  3. Anonymous users2024-02-14

    Too much humidity or heat can affect viscosity.

  4. Anonymous users2024-02-13

    If you have plastic products, you can just put them in the microwave and heat them in other ways! For other metal products, use 502 glue!

  5. Anonymous users2024-02-12

    First of all, the glass bottle should be cleaned, the oil and dust should be removed, and then the moisture should be removed (fire), and the self-adhesive should be heated and pressed after sticking.

  6. Anonymous users2024-02-11

    502 will be corrosive Water glass is a liquid state of sodium silicate, which is mostly called water glass in the south and bubble alkali in the north. Sodium silicate is commonly known as water glass, and liquid sodium silicate is a colorless, slightly colored transparent or translucent viscous liquid. Solid sodium silicate is a colorless, slightly colored transparent or translucent glass block.

    There are three forms: liquid, solid, and water quenching. Theoretically, such substances are called "colloids".

  7. Anonymous users2024-02-10

    There are several kinds of materials that need to be sprayed primer, such as ABS can be sprayed directly, such as PP to spray special primer, I don't know what kind of plastic you use?

  8. Anonymous users2024-02-09

    Depending on the reaction in your basin, generally if it is not very violent, the plastic basin should not be burned.

    Caustic soda can only corrode aluminum basins, not plastic basins, for fear that the temperature inside is too high and the plastic basins will be burned.

    It's not poisoning, it's a small amount of lime getting into the nose, and you'll be fine with a mask.

  9. Anonymous users2024-02-08

    Good afternoon, PBT can not be bonded with epoxy resin, it is the same inert surface as PP, the correct resin for grafting should be PA or CPP (polyamide, chlorinated polypropylene), and the upper Hu sedan PBT should be primed with silane coupling agent, and then the adhesion promotion layer, and finally the other workpieces you want to bond. Epoxy resins can only bond non-olefin plastics. Do a good job of surface degreasing before bonding, and it is recommended to use CPP.

    Let's try it first.

  10. Anonymous users2024-02-07

    The same size, the one that is dense, the one that cools down quickly.

    The glass bottle is dense, the heat transfer is fast, and of course the water in the glass bottle cools quickly. Plastic ones should be slow.

    For example, if it is foam, it is slower because the foam density is too small.

Related questions
5 answers2024-08-15

Heating the basin over low heat (about 40 to 50 degrees), adding a small amount of water several times, or kneading the dough more often can prevent the dough from sticking.

34 answers2024-08-15

Don't worry about this, the baby also likes new things, just like me and my daughter, there are other acquaintances who will not look for me, the baby and the mother are together every day, it will be very boring for a long time, and there will be a good impression when you meet people who like to tease themselves, however, the baby is still the closest to the mother in the bottom of my heart, such as sleeping will be obvious when you sleep, take the baby out to play, see different people and things, the baby will grow super fast. . . Hope it helps... May the baby grow up healthy and happy...

6 answers2024-08-15

The solid glue has been left for a long time to dry out and the specific steps to restore the stickiness: >>>More

17 answers2024-08-15

1. Press a piece of glass on top of the plastic tablecloth. >>>More

9 answers2024-08-15

Put more water, add more oil, it has nothing to do with the iron plate, I don't have a good grasp of the proportion of water and oil, I must add too much water, sauce, chili, cumin, are the root of sticking to the pan, and the ingredients needed to master the proportion are good. >>>More