How to use cloth stickers? How to stick a cloth sticker on clothes

Patches can be used to patch holes and stains on clothes, or they can be ironed or sewn on your favorite fabrics according to your creativity.

1.Keep the back clean before ironing, and adjust the temperature to a suitable temperature for the garment according to the method of using the iron.

2.Put the cloth sticker in the appropriate position you need (don't tear off the glue), and blanch it back and forth a few times, generally about 15 seconds.

3.To prevent burns, you can put a thin layer of cotton cloth on the cloth (not a faded cloth). After scalding, check the edges to see if they are hot, and blanch the edges a few more times.

4.It is also necessary to determine the temperature according to the thickness of the cloth, and the thicker one must be higher and the hot time longer. For particularly thick cloth stickers, you can burn it a few more times on the back.

5.For cloth stickers embroidered with sequins or metal thread, iron them from the back side first, and then trim the corners from the front after the cloth stickers are firmly fixed to avoid damaging the sequins or other accessories on the front.

6.The best way is to use a needle and thread to sew a few stitches on the edge of the cloth sticker after ironing, which is stronger and more conformable.

7.If you don't have an iron at home, you can also sew the cloth directly on the clothes with threads of the same color.

You can buy the one sewn with a sewing machine, it's very convenient, it's three-dimensional, and it's beautiful! As for this cloth sticker, it is ironed with a steam iron!

1. Put the cloth sticker where you need it and spread a layer of cloth.

2. Turn the iron to the steam setting and heat the cloth.

3. After ironing, the cloth sticker has been glued to the clothes.

4. If you are worried that the cloth sticker will fall off, you can use the car thread to sew it again.

Also known as patching flowers, the original meaning is the patch used for repairing clothing, and now it refers to woolen embroidery, denim embroidery, embroidery cloth stickers, lace armbands, gold thread embroidery badges, etc., which are a kind of clothing decoration accessories.

Cloth paste process, also known as silk silk pile embroidery, originated in the Tang Dynasty, through the Tang, Song, Yuan, Ming, Yu socks Qing Dynasty development, until the last generation of the 90s, gradually formed a fusion of a variety of techniques, gorgeous colors, fine workmanship, and has the artistic characteristics of bas-relief effect. Carefully pasting various fabrics into various works such as plums, orchids, bamboos, and chrysanthemums requires the exquisite skills of the artist.

Place the cloth sticker where it needs to be and spread a layer of cloth. Turn the iron on the steam setting and heat the cloth. After ironing, the cloth stickers are already glued to the clothes. If you are worried that the cloth sticker will fall off, you can use the car thread to sew it again. <

1. Put the cloth sticker where you need it and spread a layer of cloth.

2. Turn the iron to the steam setting and heat the cloth.

3. After ironing, the cloth sticker has been glued to the clothes.

4. If you are worried that the cloth sticker will fall off, you can use the car thread to sew it again.

Cloth stickers were first sewn on damaged clothes, and later skillfully hand-made patterns were patched on clothes. Nowadays, many people use cloth stickers to decorate their clothes, so today I will teach you how to stick cloth stickers on clothes.

Tools: cloth stickers, clothes, irons, cotton cloths.

First of all, we lay the clothes flat on the table, and lay the cloth with the hot melt glue on the side of the clothes.

Finally, if you gently remove the cotton cloth, you will find that the cloth sticker has been perfectly attached to the clothes.

First, first tidy up the walls, measure the walls now, and then buy wall coverings.

Second, after the wallcovering is ready, there should be proprietary tools, which can also be purchased together when buying the wallcovering. Cloth knives, base films and wall adhesives.

Third, apply the base film first, on the wall, this should be applied according to the actual situation of the wall, brush twice, with an interval of 24 hours.

Fourth, adjust the glue and prepare to paste the wallpaper. Adjust the thickness of the glue according to the display on the package.

Fifth, start from a certain corner of the wall, apply wall glue evenly, and roll it up and down evenly.

Sixth, the last wall cloth, the two people work faster together, especially in the shade corner, the two ends are straightened from top to bottom, and it is better to scrape and paste from the inside to the edge. During the pasting process, wipe off the excess glue with a clean, damp towel. After sticking the whole house, conduct a comprehensive inspection, and find that there are bubbles and bubbling can be solved by scalding it with a household steam iron.

Here's how to make a cloth sticker:

1. First of all, before making cloth stickers, we must first prepare some basic materials, including cloth, white latex, artwork paper, pencils, cardboard, scissors, carbon paper, and fluffy cotton.

2. Secondly, the first is to draw, the pattern design can use their usual collection, the appropriate to stay, they don't like to remove, common patterns are animals, landscapes, flowers and fruits, people, etc., this step is a complete test of the author's ability to innovate and appreciate.

3. The third step is to topography the pattern, put the carbon paper in the middle of the base map and the cardboard, and cut the pattern after drawing the pattern is the pattern of the cloth sticker.

4. The fourth step is to paste the filler in the pattern, apply a layer of glue around the pattern, paste the work on the fluffy cotton (if there is no requirement for three-dimensionality, you can also do not use fluffy cotton), and cut off the other excess parts after sticking.

5. The fifth step is to cut the fabric according to the shape of the cardboard, and then paste the fabric. There are many ways to paste the fabric, this step is a simple explanation, if you want to carry out edging, you should pay attention to leaving 1-2 mm for edging when cutting; If you want to make it simpler, just cut and paste the shape of the part with scissors, and paste it directly.

6. The sixth step is to put the fabric just pasted on the base map of the work in order and then paste and combine, and the main parts can be spliced first, and finally the secondary parts can be spliced.

7. The seventh step is to make the bottom lining board, the thickness of the cardboard is millimeters, and the size of the work is cut. Glue the cloth firmly with the cardboard.