Renovate the house with laminate flooring on top of the tiles, what about the bathroom and kitchen?

The house is renovated, the tiles are covered with laminate flooring, the bathroom and kitchen cannot be re-tiled, and all the tiles must be removed and re-tiled.

Bathrooms and kitchens are best tiled, can not be paved floor, if you want to renovate, or to remove the original tiles, re-tiling, if there is no problem with the floor tiles, do not change it.

Renovate the house with laminate flooring on top of the tiles, the kitchen of the bathroom is a room with water, the floor should be lower than the living room and bedroom, and it cannot be thickened on the original floor, it is better to do it again.

What about renovating the house, laying laminate flooring on top of wall tiles to the bathroom and kitchen? If you have a room or a house, you can also redecorate it on the third day and the kitchen, and you can also re-lay it on the floor in Chongqing, I think it will be re-laid.

In general, I think it's like this one for the bathroom and kitchen. It can be directly from the three general cases, I think that the bathroom and kitchen like this one, you can directly choose from three aspects, and if this kind of problem occurs, you can directly go to the background to replace it.

It is best to use porcelain tiles in the bathroom. Because the bathroom is often exposed to water, laminate flooring is not suitable.

Bathrooms and kitchens should be tiled, not wooden.

Renovate the house, what about the bathroom and kitchen over there with laminate flooring on top of the tiles? Bathrooms and kitchens can also be refurbished.

Whether to change the tile to wood floor to play porcelain tiles, whether to change the tile to change the floor to play tiles, this is not a hard requirement, to be decided according to the actual situation. The solidification of ceramic tiles and cement is different, and the effect after striking is also different. The tiles of the old house, first of all, look at the abundance of the paste is not firm, if you can knock it full, you can knock off the tiles, because the construction is relatively simple, and the ground leveling is easier.

If the cement quality of the porcelain tile is very good, it is difficult to knock off the porcelain piece, and the ground after knocking off the porcelain piece has the undulation of cement, it is best not to knock off the porcelain piece, otherwise the amount of construction work is large.

Depending on the wood material to be laid, different wooden floors require different surfaces to be laid. If you want to lay a solid wood floor, you must knock off the tiles, because the solid wood floor is to hit the keel, and the keel cannot be hit on the tile, so it is very fragile. If you want to lay laminate flooring, you don't need to hit tiles, you can directly lay laminate flooring on the tiles, and the moisture-proof and insulated soil can be directly laid.

Because it is difficult for the original cement and the cement used for the later bricks to be peeled off intact, they will generally be beaten together when knocked off, and there should be 4-5 cm of cement under the porcelain tiles that are generally paved (too thin porcelain tiles will be uneven later.)

See if there are pipelines underground, many homes now have pipes underground, so we have to consider this issue when considering whether to knock off the tiles. If the pipes of an existing house are laid underground, then demolition is likely to damage those pipes. In this case, do not knock off the tiles.

Whether to knock off the tile, before construction, to ensure that there is no dust on the ground, and the tile can not have unevenness, if there is such a situation, but also to repair the tile until level. To lay ceramic tiles like this to save the cost of decoration, but if the old ceramic tiles are actually uneven and not clean, processing ceramic tiles can increase the decoration funds, so it is not cost-effective.

It is necessary to smash the original one, and carefully smash the pipes buried underneath; It is easy to resurface laminate flooring, clean the original floor, and directly lay the laminate floor. It's just that I don't know what your condition is, and if necessary, the baseboard will have to be smashed and pasted with a baseboard that matches the wooden floor.

You can shovel off the tiles, or you can lay laminate flooring directly on top of the tiles, either way, as long as the ground is flat, there will be no problems.

There's no need to shovel off, you just need to re-layer the floor with a new layer of laminate flooring.

1. You can directly remove the composite floor and lay tiles. If you are concerned about the floor elevation, you can chisel off the cement mortar screed before laying the tiles.

2. Precautions for tile laying:

Before laying the floor tiles, they should be soaked to avoid the absorption rate of the floor tiles leading to the absorption of water in the cement and the appearance of tightening and cracking. The volume ratio of cement sand for laying floor tiles is best about 1:5, sprinkle and stir evenly, and the thickness should be about 3cm; The joint layer and the floor tiles should be paved at the same time in sections, and cement slurry or dry mud should be used for bonding when paving.

The surface of the floor tile surface layer is clean, smooth and solid after half an hour after being pasted with a water rag; The width of the joint between the porcelain plates should meet the design requirements, and the width of the joint should not be greater than 2 mm. Unless there is a design requirement. Antique bricks are considered separately.

3. Laminate flooring is one of the types of flooring. However, laminate flooring is artificially altered in the natural structure of the flooring material to achieve a certain physical performance that meets the expected requirements. Laminate flooring often refers to laminate flooring and solid wood flooring in the market.

Summary. The laminate floor in the living room is very difficult to take care of, how to replace the laminate floor with tiles, in fact, it is very easy, but there is a premise to consider, the thickness of the wooden floor with floor tiles. To add 3, 4 cm.

It depends on the jamb of several of your doors. Is it suitable? If you don't meet these conditions, then you have to see if the floor in the living room is needed, or if you can drop the cement on the surface to about three centimeters, if you can, you can make up iron.

The laminate floor in the living room is very difficult to take care of, how to replace the laminate floor with tiles, in fact, it is very easy, but there is a premise to consider, the thickness of the wooden floor with floor tiles. To add 3, 4 cm. It depends on the jamb of several of your doors.

Is it suitable? If you don't meet these conditions, then you have to see if the floor in the living room is needed, or if you can drop the cement on the surface to about three centimeters, if you can, you can make up iron.

Replaced with tiles will not be higher than the floor of the room.

It's going to be a little bit higher.

1. Paste new tiles directly on the old tiles. First of all, it is necessary to remove the dust and dirt on the surface of the old tile, and then use the tile adhesive to do the base layer on the old tile, and the new tile can be directly pasted after the batch is completed. The adhesive should also be applied thin on the back of the new tile, and the thickness should be subject to the back pattern of the covered tile, so that the new tile will be more firmly glued.

When paving new tiles, use a rubber hammer to tap the new tile edge to adjust the edge, you need to pay attention to the reserved expansion joint, 24 hours later, wait for the tile adhesive to dry thoroughly, and use the grout to hook the joint. With the right tools, consumers can DIY on their own.

2. Clean the old tiles to make the tiles as bright as new. The tools for this trick are simple, clean brushes, toothpaste, ordinary candles. Start by squeezing an appropriate amount of toothpaste on the brush and then brush directly the joints of the tiles.

The amount of toothpaste can be decided according to the actual situation of the oil stain at the tile joints. Because the direction of the tile joints is longitudinal, it should also be brushed longitudinally when brushing, so that the oil can be brushed clean. In addition, the main raw materials at the junction of the tile are putty and white cement, so it is difficult to scrub the oil stain after sticking to it, and toothpaste has a strong cleaning effect, so choose it as a cleaning tool.

But the tile behind the stove and the tile joints are easily stained with oil, and it is really troublesome to clean it like this every time, what should I do? Thankfully, Kai has a trick, and the key tool is this ordinary candle. Apply the candle lightly to the joints of the tiles, first vertically, so that the joints can be evenly coated with the candles; Then apply it horizontally, so that the thickness of the candle and the thickness of the tile are equal.

Why do you want to smear candles? Because the surface of the candle is smooth, even if there is oil staining it, it can be cleaned with just a light wipe. Later, clean the grease stains on this tile and tile joints behind the stovetop, just scrub it with detergent.

The key to this trick is to scrub away the grease from the tile joints behind your kitchen stove with toothpaste, and apply candles to the joints to keep the tile joints free of oil.

3. Tile film. The ** wall film is a volume, the wall is very suitable for busy and the pursuit of exquisite life, fast-paced life is fast and easy, a beautiful pattern that has been carved only needs to be pasted in the position that needs to be decorated, compared to the decoration team to design and produce a higher cost of decorative wall, it is really convenient and practical.

The above is the old renovation method I shared with you in the kitchen and bathroom, I hope it can help you.

How to renovate old tiles in the kitchen and bathroom? Tile renovation is an economical and affordable way to give your kitchen and bathroom a new look. Before the first salute, you can consider re-painting.

With a special tile paint, it is possible to paint the old tile with a new color, giving it a new look. This method is not only simple, but also less costly. Also, you can consider changing the color and style of the tiles.

There are a wide variety of tiles on the market for you to choose from, and you can choose the right one according to your preferences and budget. According to the range of the local market, the cost of repainting is about 10-30 yuan per square meter, while the cost of replacing tiles is between 30-100 yuan per square meter. Finally, I recommend that you carefully consider your budget and needs before renovating your tiles, and choose the right renovation method.

If you're on a budget, you can opt for the repaint method; If you want a more radical change, consider replacing the tiles. Whichever method you choose, make sure to find a professional tile renovation company to carry out the construction to ensure the results and quality of the renovation.

The specific decoration of the house can be calculated here, just enter the area + city, calculate the decoration in 3 seconds, know the real ** in advance, and easily grasp the decoration company: [Click here, free decoration**].

It is possible to directly remove the laminate floor and lay the white tiles after it. Basically, the cement is paved before the floor tiles are paved, and the cement is the main work.

Zhi is to consolidate.

DAO, moisture-proof, tile laying after screeding. If you don't lay cement on the floor, the floor will be susceptible to water and will rot quickly. Before the floor tiles are laid, they should be soaked to avoid the absorption rate of the floor tiles leading to the absorption of water in the cement and the appearance of tightness and cracking.

If the original base is cement mortar leveling, if you don't mind the floor elevation a little, you can directly remove the composite floor and lay tiles, if you mind the floor elevation, you need to chisel the cement mortar leveling layer and then lay the tiles.

If you don't mind raising the floor a little higher, don't remove the laminate floor and lay the tiles. It's better and flatter that way.